iwconfig was showing incorrect status messages when disassociated.
Patch fixes this by always checking for association status in
ioctl calls for getting ap address.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00lib_beacondone() is called from interrupt context,
this means we cannot use the mac80211 interface iterator
that uses the rtnl lock (since that uses a mutex which can sleep).
Instead we should use the atomic mac80211 interface iterator.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the antenna configuration has changed we should reset
the antenna RSSI value. Otherwise the value will be influenced
by the previous configuration quality which in turn will affect
the antenna diversity.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Link quality estimation became quite low for all rt2x00 drivers
because the number of retries it took to send the frame were
counted as failure.
This does not correspond to the legacy driver link quality calculation,
by not counting it we will send somewhat more optimistic values to
mac80211.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the tx() handler runs while the device has disapeared,
we did return NETDEV_TX_OK but didn't free the skb.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch switch order of channel and freq (SIOCGIWFREQ) reports
in scan results in order to overcome wpa_supplicant inability
to handle channel numbers in 5.2Ghz band.
Wext reporting channel number is ambiguous as channels 7-12 (802.11j)
exist on both bands.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes iee80211_rx_bss_put/get imbalance
introduced by 'mac80211: enable IBSS merging' patch.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Correct always true conditionals.

Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This updates the beacon template code to upload both templates,
if we never uploaded one before.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The grf5101 RF code needs to invoke grf5101_write_phy_antenna every time the
channel is being switch.

This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.

This patch fixes it.

Thanks to Alessandro Di Marco who found this issue!

Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The max2820 RF code needs to invoke max2820_write_phy_antenna every time the
channel is being switch.

This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.

This patch fixes it.

Thanks to Alessandro Di Marco who found this issue!

Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The sa2400 RF code needs to invoke sa2400_write_phy_antenna every time the
channel is being switch.

This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.

This patch fixes it.

Thanks to Alessandro Di Marco who found this issue!

Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The static function max2820_rf_set_channel is called with conf == NULL
within its compilation unit.  Originally this defaulted to b/g channel
1, but "cfg80211 API for channels/bitrates, mac80211 and driver
conversion" (commit 8318d78a

) mistakenly
dropped this check.  This patch minimally restores the expected
behavior.

Reported-by: Colin Lai <colin_sh@163.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Herbert Xu points out that the use of seperate feature bits for features
to be propagated to VLAN devices is going to get messy real soon.
Replace the VLAN feature bits by a bitmask of feature flags to be
propagated and restore the old GSO_SHIFT/MASK values.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

fmvj18x_cs: The manfid of "NextCom NC5310 rev B" is MANF_ID_FUJITSU.
            but this card is MBH10302 based card.
            use ConfigBase to detect the cardtype for this card.

Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

            keep bit7,8 of XIRCREG42_SWC1 in set_multicast_list.

Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

If alloc_skb failed, the recieved packet will be dropped. Do not increase
rx_bytes for dropped packet.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Use standard routine for queue purging.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Use standard routine for queue purging.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Commit cac1f3c8

 factored out the code for get_phy_id so that it
could be reused in multiple places.  Turns out that some of the
users can be modular, so we need to export this symbol as well.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The purpose of nla_parse_nested_compat() is to parse attributes which
contain a struct followed by a stream of nested attributes.  So far,
it called nla_parse_nested() to parse the stream of nested attributes
which was wrong, as nla_parse_nested() expects a container attribute
as data which holds the attribute stream.  It needs to call
nla_parse() directly while pointing at the next possible alignment
point after the struct in the beginning of the attribute.

With this patch, I can no longer reproduce the reported leftover
warnings.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

WAN: protect protocol list in hdlc.c with RTNL.

Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The following code appears in the function fs_init_instance in the file drivers/net/fs_enet/fs_enet-main.c.

	if (fep->ops == NULL) {
		printk(KERN_ERR DRV_MODULE_NAME
		       ": %s No matching ops found (%d).\n",
		       ndev->name, fpi->fs_no);
		err = -EINVAL;
		goto err;
	}

This code implies that at the point of err, fep->ops can be NULL, so an
extra test is needed before dereferencing this value.

This problem was found using the following semantic match
(http://www.emn.fr/x-info/coccinelle/

)

// <smpl>
@@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@

* if (E == NULL)
{
  ... when != if (E == NULL) S1 else S2
      when != E = E1
* E->f
  ... when any
  return ...;
}
else S3
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

- Updated version number

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

- Added napi support when MSIX is enabled.
- Moved test_msi function from s2io_open to probe function.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

- Move all the transmit completions to a single msi-x (alarm) vector.
- Enable the continuous timer interrupt for only one transmit fifo.

Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The lifespan of the device covers the request_irq .. free_irq interval.

The cast of a void * pointer is not needed either.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* Resolve some locking issues using atomic_inc/atomic_dec
* move status code in cpmac_check_status
* unmark the BROKEN flag in Kconfig
* move code which should have been in platform code in
  arch/mips/ar7/platform.c
* fixed an IRQ storm which lets the kernel hang
* fixed a double call to netif_start_queue which causes a kernel panic
* don't fail to register the PHY, works on many devices now

Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The use of unsigned long causes the driver to fail on 32-bit systems
which support 64-bit resources.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add support for Apple USB Ethernet Adapter.

http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?nplm=MB442Z/A



Signed-off-by: Aurelien Nephtali <aurelien@sitadelle.com>
Acked-by: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch adds netpoll support for the uli526x ethernet driver --
simply call the interrupt handler for polling.

To do this without disable_irq()/enable_irq() pair we should fully
protect the handler. Luckily, it's already using irqsave spinlock,
the only unprotected place is interrupts re-enabling write. It was
safe to re-enable interrupts without holding the spinlock, but with
netpoll possibility now it doesn't seem so.

Patch was tested using netconsole and KGDBoE.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

We were passing NULL as the device.  When we actually start supporting
more interesting memory configurations, this will break things, so
we proactively are fixing the bug.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

 PHYLIB was first marked as BROKEN on S390, then the enclosing menu marked
as non-S390, then the two dependencies merged with the conversion to
menuconfig.  Reduce to non-S390.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

IPv4 would work with this driver only with static arp table entries,
the patch  reverts a padto introduced in

 commit 26a17b7b


 sc92031: start transmit return value bugfix

The padto does not work because the driver code evaluates `len' later on and
there are cases where skb->len is not updated accordingly.

This was observed with ARP frames (skb->len = 42 bytes, !skb_cloned(),
skb_tailroom = 84 bytes). Then in skb_pad(), the first condition is true, where
skb->len is not updated. As a consequence, the driver uses 42 bytes instead of
the 60 bytes, and the ARP frame never makes it onto the wire.

Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

 Use netdev_alloc_skb.  This sets skb->dev and allows arch specific
allocation.  Also simplify and cleanup the alignment code.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

nv_open() resets multicast settings, call nv_set_multicast(dev)
to restore them.  (Maybe this should rather be moved into nv_open())

Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>