- Jan 01, 2014
-
-
Emmanuel Grumbach authored
This channel inhibition for channel 14 was wrong. Fix it. Signed-off-by:Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
Emmanuel Grumbach authored
Don't check if mvm->fw->cs is NULL since it can't be. cs is an array member of iwl_fw, it can't be NULL. Use memset(ptr, 0, sizeof(*ptr)); instead of memset(ptr, 0, sizeof(struct ptr_type)); Signed-off-by: -
Emmanuel Grumbach authored
The firmware needs to be stopped quickly (100ms) after the RFKILL interrupt fired. Failing to do so would allow the firmware to access the radio registers which would lead to a hardware error. Before this change, we would kill the firmware only when mac80211 stops the device which can take a fair amount of time. Take a shortcut by stopping the device right away in the interrupt. This is not relevant if the current firmware is INIT firmware since that firmware can run while in RFKILL. Signed-off-by: -
Emmanuel Grumbach authored
Calling stop_device when start_fw wasn't called would issue: Stopping tx queues that aren't allocated... Also allow the op_mode to call stop_device and then to disable the Tx queues - in that case just silently ignore the disabling on the Tx queues, since the PRPH registers aren't reachable any more. Signed-off-by: -
Emmanuel Grumbach authored
This is useless and introduces a dependency between rfkill and stop_device - the op_mode can't call stop_device from the rfkill notification since it would lead to an endless recursion. Next patches will need to do so. Signed-off-by: -
Emmanuel Grumbach authored
Under very specific circumstances, the firmware might ignore a host command. This was debugged and we ended up seeing that the power management hardware was faulty. In order to workaround this issue, we keep the NIC awake as long as we have host commands in flight. This will avoid to put the hardware into buggy condition. Signed-off-by: -
Eytan Lifshitz authored
In case of invalid section_id, the function returns after it aleready allocated memory. Fixed by change the order of actions. Signed-off-by:
Eytan Lifshitz <eytan.lifshitz@intel.com> Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
The AC / fifo mapping was wrong - BE packets landed in VO FIFO. The iwl_mvm_tx_fifo enumeration isn't in the same order as ieee80211_ac_numbers enumeration. Since the firmware relies on fifo / ac mapping - this led to wrong behavior. E.g. the firmware sends beacon with the same QoS parameters as VO, and it actually took the parameters of BK. There are probably more severe issues. Reviewed-by:
-
- Dec 22, 2013
-
-
Emmanuel Grumbach authored
This lock was never acquired in the primary interrupt handler, but since it was acquired along with irq_lock which had to disable interrupts, rxq->lock had to disable interrupts too. Now that trans_pcie->irq_lock isn't acquired in the primary interrupt handler, rxq->lock can let interrupt enabled. Reviewed-by:
-
Emmanuel Grumbach authored
Since we don't take this lock in the primary interrupt handler, there is no pointin disabling the interrupt in the critical section protected by trans_pcie->irq_lock. Reviewed-by:
-
Emmanuel Grumbach authored
Handling interrupt with no cause and printing logs doesn't need to be ICT / non-ICT specific move this to the common code. Reviewed-by:
-
Emmanuel Grumbach authored
This was useful when the handling was not in the same context as the interrupt cause retrieval: we could have several hard interrupts until the handler gets called. Since we retrieve the interrupt cause in the handler itself, there is no need to OR the interrupt causes. Reviewed-by:
-
Emmanuel Grumbach authored
These functions are meant to return an interrupt cause and not an irqreturn_t. We still return IRQ_HANDLED if we had an error and IRQ_NONE if our device hasn't fired any interrupt. Reviewed-by:
-
- Dec 18, 2013
-
-
Emmanuel Grumbach authored
Instead of having: iwl_pcie_irq_handler iwl_pcie_isr_ict iwl_pcie_isr_non_ict we now have: iwl_pcie_irq_handler: if (use_ict)) iwl_pcie_int_cause_ict; else iwl_pcie_int_cause_non_ict; This is much clearer. Signed-off-by: -
Emmanuel Grumbach authored
We now disable the interrupts in the hardware from the upper half and all the rest (including reading the interrupt cause) is done in the handler. Reviewed-by:
-
Emmanuel Grumbach authored
The purpose of this is to be able to call these functions from the interrupt handler and not from the primary interrupt handler. Reviewed-by:
-
Emmanuel Grumbach authored
Separate the code that simply disables interrupt in the hardware and the code that checks what interrupt fired. This will be useful to move the second part in the threaded handler which will be done in a future patch. Reviewed-by:
-
Emmanuel Grumbach authored
Track the interrupt mask in software, making it exactly what is configured in the interrupt mask register in the hardware. This allows not to access the register from the interrupt handler. This was the case for ICT interrupt already, but not for non-ICT interrupt. Reviewed-by:
-
Emmanuel Grumbach authored
Since iwl_trans_pcie_alloc_ict is called in the PCIe allocation code, we always set CSR_INT_BIT_RX_PERIODIC. Move that bit to the default list of interrupts we enable and simplify the code. Also use dma_zalloc_ and avoid to memset the memory afterwards. trans_pcie->ict_index is 0 since trans_pcie has just been kzalloced, remove the redundant assignment. Reviewed-by:
-
Johannes Berg authored
Signed-off-by:
EyalX Shapira <eyal@wizery.com> Signed-off-by:
-
Eyal Shapira authored
RTS protection was turned on once aggregation was enabled but it was never turned off. Remove turning on RTS protection in the LQ command completely as TX_CMD_FLG_PROT_REQUIRE gets set in iwl_mvm_set_tx_cmd for every Tx which is part of an aggregation. This would already cause RTS protection to be used during aggregations. Signed-off-by:
-
Eyal Shapira authored
Set the Tx/Rx highest long GI rates in the VHT Supported MCS Set field according to the chip capabilties. Signed-off-by:
-
Eyal Shapira authored
MCS9 introduces some corner cases in the current rs algorithm which may lead to non optimal throughput and instability in the throughput. Until all the corner cases are resolved disable MCS9 for Tx as a workaround which yields better throughput results as MCS8 is much more stable. Signed-off-by:
-
Ilan Peer authored
Fix a regression introduced in "iwlwifi: mvm: fix ht protection flags" where an AP/IBSS MAC context could have been updated even before the context was added to the FW. This fix avoids the following warning: WARNING: ... at .../drivers/net/wireless/iwlwifi/mvm/mac-ctxt.c:1132 iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]() Changing inactive MAC 0c:8b:fd:01:1a:30/3 Modules linked in: [...] Call Trace: [<c16041fd>] dump_stack+0x41/0x52 [<c1041074>] warn_slowpath_common+0x84/0xa0 [<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<c1041133>] warn_slowpath_fmt+0x33/0x40 [<f80d8f45>] iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<f80d517a>] iwl_mvm_bss_info_changed+0x22a/0x4b0 [iwlmvm] [<c160831d>] ? mutex_unlock+0xd/0x10 [<f80d4678>] ? iwl_mvm_configure_filter+0x58/0x70 [iwlmvm] [<f80d4f50>] ? iwl_mvm_mac_tx+0xc0/0xc0 [iwlmvm] [<f8132d83>] ieee80211_bss_info_change_notify+0xa3/0x1d0 [mac80211] [<f8149247>] ? ieee80211_del_virtual_monitor+0x127/0x1f0 [mac80211] [<f8149cac>] ieee80211_do_open+0x12c/0xeb0 [mac80211] [<c106c6de>] ? __raw_notifier_call_chain+0x1e/0x30 [<c106c70f>] ? raw_notifier_call_chain+0x1f/0x30 [<f814aa8d>] ieee80211_open+0x5d/0x60 [mac80211] [<c1500c7b>] __dev_open+0xab/0x140 [<c160b39a>] ? _raw_spin_unlock_bh+0x2a/0x30 [<c1500f41>] __dev_change_flags+0x81/0x160 [<c10ab6fc>] ? __lock_is_held+0x3c/0x60 [<c15010d1>] dev_change_flags+0x21/0x60 Signed-off-by:Ilan Peer <ilan.peer@intel.com> Reported-by:
-
Emmanuel Grumbach authored
debufs.o appeared twice in the Makefile. Fix that. Signed-off-by: -
Eyal Shapira authored
Extract the scale action decision to a different function in preparation of modifying it. While at it also convert the scale action values from hardcoded values to a clear enum. Signed-off-by:
-
Eyal Shapira authored
The logs are emitted in a flow in which there were retries and the rates in the rate table entry didn't match the active or search table. This doesn't indicate a problem and is expected in most cases where there will be retries for some reason. Remove the logs. Signed-off-by:
-
Eyal Shapira authored
The new logic will attempt more rates with less retries per rate. Also when starting off with MIMO it will fallback to SISO with the same MCS and only then to Legacy. Previously we fell back directly to Legacy. Signed-off-by:
-
Eyal Shapira authored
The supported legacy rate mask is initialized when rs is initialized based on the remote peer supported rates. There's no need to re mask it repeatedly with the supported remote peer rates. Signed-off-by:
-
Eyal Shapira authored
Simplify the code a bit more by extracting the rates table building logic into a separate function and handle setting a fixed rate for debug in a separate flow. Also avoid using and saving ucode rate format in different places. Instead use rs_rate struct and convert to ucode format only when filling the rates table in the LQ command. Signed-off-by:
-
Alexander Bondar authored
Current firmware doesn't handle well uAPSD in P2P Client. When it will be fixed, the firmware will set a TLV flag to notify the driver that uAPSD is supported in P2P client mode. Check this flag when sending power command for P2P client. Signed-off-by:
Alexander Bondar <alexander.bondar@intel.com> Signed-off-by:
-
Arik Nemtsov authored
It is not currently implemented for SDIO, and not required for other slave buses as well. Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
-
Arik Nemtsov authored
Clear the FW_ERROR status before the common start_fw transport code. Remove the transport specific clears. After these patches the FW_ERROR flag is only set and cleared by common transport code. Signed-off-by:
-
Arik Nemtsov authored
In case a sync command timeouts or Tx is stuck while a FW error interrupt arrives, we might call iwl_op_mode_nic_error twice before a restart has been initiated. This will cause a reprobe. Unify calls to this function at the transport level and only call it on the first FW error in a given by checking the transport FW error flag. While at it, remove the privately defined iwl_nic_error from PCIE code and use the common callback instead. Signed-off-by:
-
Eliad Peller authored
iwl_nvm_init() return value wasn't checked in some path, which resulted in the following panic (if there was some issue with the nvm): Unable to handle kernel NULL pointer dereference at virtual address 00000004 pgd = d0460000 [00000004] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP Modules linked in: iwlmvm(+) iwlwifi mac80211 cfg80211 compat [last unloaded: compat] PC is at iwl_mvm_mac_setup_register+0x12c/0x460 [iwlmvm] LR is at 0x2710 pc : [<bf50dd4c>] lr : [<00002710>] psr: 20800013 sp : d00cfe18 ip : 0000081e fp : d006b908 r10: d0711408 r9 : bf532e64 r8 : d006b5bc r7 : d01af000 r6 : bf39cefc r5 : d006ab00 r4 : d006b5a4 r3 : 00000001 r2 : 00000000 r1 : d006a120 r0 : d006b860 Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Emmanuel Grumbach authored
This pointer was not used anywhere. Signed-off-by: -
Eyal Shapira authored
Move rs_program_fix_rate right before it's caller where we're already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so we can get rid of the extra ifdefs surrounding the original location. Signed-off-by:
-
Arik Nemtsov authored
Stop Tx and commands from arriving to the transport layer when a FW error has occurred. A HW recovery should take place before. Remove transport specific checks of the same nature (note that not all transports were protected). Signed-off-by:
-
Arik Nemtsov authored
The same bits are employed in all transport layers. Put the status field in the common transport layer. This allows us to employ them in common transport code. Signed-off-by:
-
Arik Nemtsov authored
The stop_hw trans callback is not well defined. It is missing in many cleanup flows and the division of labor between stop_device/stop_hw is cumbersome. Remove stop_hw and use stop_device to perform both. Implement this for all current transports. PCIE needs some extra configuration the op-mode is leaving to configure RF kill. Expose this explicitly as a new op_mode_leave trans callback. Take the call to stop_device outside iwl_run_mvm_init_ucode, this makes more sense and WARN when we want to run the INIT firmware while it has run already. Signed-off-by:
-
