Ls1028a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Ls1012a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Ls1088a platform, the i2c input clock is actually platform pll CLK / 8
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update the nodes to include little-endian
property to be consistent with the hardware.

Signed-off-by: Song Hui <hui.song_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Thermal Monitoring Unit (TMU) monitors and reports the
temperature from 2 remote temperature measurement sites
located on ls1028a chip.
Add TMU dts node to enable this feature.

Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Making audio_pll1 parent of audio_pll1_bypass, will allow
setting rates multiple of 8000 for children.

After unbypass clk hierarchy looks like this:
 * osc_25m
   * audio_pll1
     * audio_pll1_bypass
       * audio_pll1_out
         * sai2
           * sai2_root_clk

Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add opp-suspend property to each OPP, the of opp core will
select the OPP HW supported and with highest rate to be
suspend opp, it will speed up the suspend/resume process.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since fsl-ls1088a Soc GPIO registers are used as little endian,
the patch adds the little-endian attribute to each gpio node.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the console device tree node for the following
DPAA2 based platforms: LS1088A, LS2080A, LS2088A and LX2160A.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

TechNexion PICO-PI-IMX8M-DEV evaluation and development kit based on
NXP i.MX8M Quad applications processor. Datasheet can be found at:

https://s3.us-east-2.amazonaws.com/technexion/datasheets/picopiimx8m.pdf



The current level of support yields a working console and is able to boot
userspace from NFS or init ramdisk.

Additional subsystems that are active :
	- Ethernet
	- USB

Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Andra Danciu <andradanciu1997@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8QXP serial alias for lpuart ports.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add imx8qxp lpuart baud clock.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch use the optional property node "arm,malidp-arqos-value" to
can be dynamic configure QoS signaling.

Signed-off-by: Wen He <wen.he_1@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for i.MX8QXP AI_ML board from Einfochips. This board is one
of the Consumer Edition boards of the 96Boards family based on i.MX8QXP
SoC from NXP/Freescale.

The initial support includes following peripherals which are tested and
known to be working:

1. Debug serial via UART2
2. uSD
3. WiFi
4. Ethernet

More information about this board can be found in Arrow website:
https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools



Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All these at803x properties are not documented anywhere, so
just remove them.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ls1046afrwy board is based on nxp ls1046a SoC.
Board support's 4GB ddr memory, i2c, microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.

Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the charge controller node. With the controller driver loaded
the VBUS of the user USB socket is controlled exclusively via i2c
with the GPIO controls ignored, so vbus-supply for the user USB
port must be linked to the charge controller.

Hog the previously used GPIO control to unconditionally enable
VBUS until the driver is loaded.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The correct clock for "bus_early", "ref", "suspend" should be:
IMX8MQ_CLK_USB1_CTRL_ROOT, IMX8MQ_CLK_USB_CORE_REF, IMX8MQ_CLK_32K,
especially we may need the right suspend clock rate to set register
in controller driver.

Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MQ has clock gate for TMU module, add clock info to TMU
node for clock management.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.

That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.

https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdf
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf

Fixes: 12629c5c

 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to latest datasheet (Rev.0.2, 04/2019) from below links,
1.8GHz is ONLY available for consumer part, so the market segment
bits for 1.8GHz opp should ONLY available for consumer part accordingly.

https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdf
https://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf

Fixes: f403a26c

 (arm64: dts: imx8mm: Add cpu speed grading and all OPPs)
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MM can reuse i.MX8MQ's src driver, add "fsl,imx8mq-src" as
src's fallback compatible to enable it.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The same ddr perfomance counter IP from 8qxp is also available on imx8m
series so add it to dts.

Tested with `perf stat` and `memtester` on imx8mm-evk and obtained
plausible results.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

USB1 port has typec connector with power delivery support:
- Dual data role: host and device.
- Dual power role: source and sink, prefer power sink.

Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since IMX8MM_CLK_USB_CORE_REF is not used at all, so remove the setting
for it.

Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MM pinctrl driver.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MQ pinctrl driver.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the initial configuration for clocks that need default parent and rate
setting. This is based on the vendor tree clock provider parents and rates
configuration except this is doing the setup in dts rather than using clock
consumer API in a clock provider driver.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This enables the Mixel MIPI D-PHY on the Librem 5 devkit

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Acked-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a node for the Mixel MIPI D-PHY, "disabled" by default.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Acked-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull Devicetree fixes from Rob Herring:
 "Fix several warnings/errors in validation of binding schemas"

* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
  dt-bindings: iio: ad7124: Fix dtc warnings in example
  dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
  dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
  dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
  dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
  dt-bindings: Ensure child nodes are of type 'object'

Pull vfs documentation typo fix from Al Viro.

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  typo fix: it's d_make_root, not d_make_inode...

Pull cifs fixes from Steve French:
 "Two fixes for stable, one that had dependency on earlier patch in this
  merge window and can now go in, and a perf improvement in SMB3 open"

* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module number
  cifs: flush before set-info if we have writeable handles
  smb3: optimize open to not send query file internal info
  cifs: copy_file_range needs to strip setuid bits and update timestamps
  CIFS: fix deadlock in cached root handling

The commit b3aa14f0 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.

   kernel BUG at drivers/iommu/iova.c:801!
    Workqueue: kblockd blk_mq_run_work_fn
    RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
    Call Trace:
     free_cpu_cached_iovas+0xbd/0x150
     alloc_iova_fast+0x8c/0xba
     dma_ops_alloc_iova.isra.6+0x65/0xa0
     map_sg+0x8c/0x2a0
     scsi_dma_map+0xc6/0x160
     pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
     pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
     scsi_queue_rq+0x79c/0x1200
     blk_mq_dispatch_rq_list+0x4dc/0xb70
     blk_mq_sched_dispatch_requests+0x249/0x310
     __blk_mq_run_hw_queue+0x128/0x200
     blk_mq_run_work_fn+0x27/0x30
     process_one_work+0x522/0xa10
     worker_thread+0x63/0x5b0
     kthread+0x1d2/0x1f0
     ret_from_fork+0x22/0x40

Fixes: b3aa14f0

 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.

Switch hexagon to use generic version of these functions.

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB updates from Jon Mason:
 "New feature to add support for NTB virtual MSI interrupts, the ability
  to test and use this feature in the NTB transport layer.

  Also, bug fixes for the AMD and Switchtec drivers, as well as some
  general patches"

* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
  NTB: Describe the ntb_msi_test client in the documentation.
  NTB: Add MSI interrupt support to ntb_transport
  NTB: Add ntb_msi_test support to ntb_test
  NTB: Introduce NTB MSI Test Client
  NTB: Introduce MSI library
  NTB: Rename ntb.c to support multiple source files in the module
  NTB: Introduce functions to calculate multi-port resource index
  NTB: Introduce helper functions to calculate logical port number
  PCI/switchtec: Add module parameter to request more interrupts
  PCI/MSI: Support allocating virtual MSI interrupts
  ntb_hw_switchtec: Fix setup MW with failure bug
  ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
  ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
  NTB: correct ntb_dev_ops and ntb_dev comment typos
  NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
  ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
  NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
  NTB: ntb_hw_amd: set peer limit register
  NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
  NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
  ...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:

Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@2000: 'clocks' is a required property

Add the missing 'clocks' properties to the examples to fix the errors.

Fixes: 2c9239c1

 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>