- Feb 20, 2010
-
-
Enric Balletbo i Serra authored
Signed-off-by:
Enric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
Signed-off-by:
-
- Feb 18, 2010
-
-
Enric Balletbo i Serra authored
Add timing data for the Numonyx M65KxxxxAM SDRAM chip, used on the IGEP v2 board. Signed-off-by:
-
Enric Balletbo i Serra authored
This patch adds support for flashes on IGEP v2 boards. For now only OneNAND is supported. Signed-off-by:
-
Enric Balletbo i Serra authored
Signed-off-by:
-
Enric Balletbo i Serra authored
Add platform init code for EHCI driver on IGEP v2 Signed-off-by:
-
Enric Balletbo i Serra authored
Fix typo on IGEP v2 board Signed-off-by:
-
Enric Balletbo i Serra authored
Add platform data for the twl4030_codec MFD on IGEP v2 Signed-off-by:
-
Grazvydas Ignotas authored
Enable DSS2 and update defconfig for current kernel. Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Signed-off-by:
-
Grazvydas Ignotas authored
Update pandora's regulator setup: - add new regulators: VAUX2, VAUX4 and VSIM - add new consumers: ads7846, nub controllers, USB PHY, audio DAC - use dev names instead of struct device pointers Signed-off-by:
-
Grazvydas Ignotas authored
This patch adds configuration data for DSS2 and sets up display related regulators. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@nokia.com> Signed-off-by:
-
Sanjeev Premi authored
GPIO175 is used for PEN_IRQ on the EVM. This patch sets the mux settings for the same. Signed-off-by:
Sanjeev Premi <premi@ti.com> Signed-off-by:
-
Sanjeev Premi authored
The keypad was not working properly after migrating to matrix_keypad. Swapped the row, col fields of the KEY() macro in the keymap definition to get it working again. Signed-off-by:
-
Sanjeev Premi authored
This patch sets SYS_NIRQ for keypad input. It also sets the same as a wakeup event from OFF mode. Signed-off-by:
-
vikram pandita authored
Zoom3 board has omap3630 EHCI port2 connected to a ULPI phy. GPIO_64 is connected to the PHY reset pin. Signed-off-by:
Vikram Pandita <vikram.pandita@ti.com> Cc: Anand Gadiyar <gadiyar@ti.com> Signed-off-by:
-
Tony Lindgren authored
-
Ranjith Lohithakshan authored
The check for a valid mux name should be performed regardless of whether DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get: Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = c0004000 [00000000] *pgd=00000000 Internal error: Oops: 5 [#1] last sysfs file: Modules linked in: CPU: 0 Not tainted (2.6.33-rc8 #10) PC is at strcmp+0x18/0x40 LR is at omap_mux_init_signal+0x68/0x14c ... This fixes the issue currently seen with boards not booting up if DEBUG_FS is not enabled in defconfig. Note that the earlier ifndef + ifdef now becomes simpler ifdef else: If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected, we only want the GPIO to mux register mapping. Signed-off-by:
Ranjith Lohithakshan <ranjithl@ti.com> Signed-off-by:
-
- Feb 16, 2010
-
-
Jorge Eduardo Candelaria authored
Add platform device for McPDM interface in OMAP4 and register its memory and irq resources. Signed-off-by:
Jorge Eduardo Candelaria <x0107209@ti.com> Signed-off-by:
-
Jorge Eduardo Candelaria authored
Define McPDM physical and L3 base address for OMAP4 Signed-off-by:
-
Jorge Eduardo Candelaria authored
Support for McPDM IRQs in OMAP4 Signed-off-by:
-
Felipe Balbi authored
sdp4430_uart_config isn't used anywhere, so remove it. Signed-off-by:
Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
-
Vaibhav Hiremath authored
Signed-off-by:
Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by:
-
Vaibhav Hiremath authored
AM3517/05 has few additional control module registers to control the new IP's, like VPFE, USBOTG, CPGMAC. This patch adds the bit defination for INTR_CLR and SW_RST control register. Signed-off-by:
-
Vaibhav Hiremath authored
Add base address definations for new AM35xx IPSS modules, like VPFE, USBOTG, CPGMAC. Please note that the OMAP34xx IVA2 memory space is being used for AM35xx IPSS modules. Signed-off-by:
Sriramakrishnan <srk@ti.com> Signed-off-by:
-
Lesly A M authored
Changes for setting the padconf value for sys_nirq line which is connected to T2 INTR1. This will fix the T2 keypad wakeup. Signed-off-by:
Lesly A M <x0080970@ti.com> Signed-off-by:
Teerth Reddy <teerth@ti.com> Signed-off-by:
-
Tony Lindgren authored
Get rid of the ifdeffery in omap_mux_init by creating omap_mux_init_package and omap_mux_init_signals functions. Signed-off-by: -
Adrian Hunter authored
It is still possible to use the omap_hsmmc module without the regulator framework. Accordingly, ifdef out regulator-specific functions. Signed-off-by:
Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by:
-
Adrian Hunter authored
EMMC can have two voltage supplies, Vcc and VccQ which are implemented in the code as consumer supplies vmmc and vmmc_aux. If the regulator that supplies vmmc_aux is shared with other consumers, then sending it to sleep will disrupt those consumers. However, the TWL4030-family regulators may have OFF remapped to SLEEP, in which case 'regulator_disable()' will put the regulator to sleep only when all consumers are disabled - which is the desired behaviour. This patch adds a platform data field to allow that option. Signed-off-by:
-
Adrian Hunter authored
Stop using 'regulator_is_enabled()' and just pair enables with disables so that the regulator reference counts can work correctly. Signed-off-by:
-
Adrian Hunter authored
Disable timeouts are in msecs not jiffies. Signed-off-by:
-
Adrian Hunter authored
An eMMC may be always powered on, so that the lowest power saving state possible is sleeping. Add a field to the platform data to indicate that. Signed-off-by:
-
Adrian Hunter authored
It has been discovered that, when eMMC is powered off, current will flow from OMAP eMMC data pull-ups to the eMMC voltage supply. Configuring pads for OMAP off-mode does not help because eMMC is powered off independently of OMAP off-mode. Hence the pads are now re-configured when eMMC is powered on or off. Signed-off-by:
-
Adrian Hunter authored
Call the PM context-loss count function, now that there is a prototype for it. Signed-off-by:
-
Adrian Hunter authored
hsmmc.[ch] no longer has any dependency on twl4030 and variable names should be renamed to reflect that. Signed-off-by:
-
Adrian Hunter authored
mmc-twl4030.[ch] no longer has any dependency on twl4030 and should be renamed to reflect that. Signed-off-by:
-
Adrian Hunter authored
This patch moves the setup code for GPIO's and Voltage Regulators from the board file mmc-twl4030.c to the driver omap_hsmmc.c. PBIAS and other system control configuration remains in the board file. Moving GPIO code to the driver makes the board initialisation code independent of when GPIO's are defined. That makes the board initialisation now entirely independent of its original twl4030 roots. Moving Voltage Regulator code to the driver allows for further development of regulator support in the core MMC code. It also permits the MMC core to be compiled as a module, because the board code no longer calls MMC core functions. Signed-off-by:
-
Vimal Singh authored
This patch adds support for flashes on 3430SDP boards. All three NAND, NOR and OneNAND are supported. I have tested it on 3430SDP (ES2 and ES3.1). This patch can be treated as an example to "how to utilize": 'gpmc-nand.c' and 'board-sdp-flash.c'. Similar patches can be created for 2430sdp and 3630sdp or any other similar board. Signed-off-by:
Vimal Singh <vimalsingh@ti.com> Signed-off-by:
-
Vimal Singh authored
This patch adds 'board-sdp-flash.c', which could be utilized by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp). This file does initialization for all three flash devices present in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number dynamically using switch setting information (S8: 1-4). This also expects partition information from core board files (for ex: board-3430sdp.c). Which allows to choose different default partitions for different boards. A new structure is created for this purpose: 'flash_partitions' in 'mach/board-sdp.h'. This has two members: 1. struct mtd_partition *parts 2. int nr_parts A board file is expected to fill this structure and pass it to 'sdp-flsash-init'. Partition information should be passed in structure array of 'flash_partitions'. Partition information should be passed in below sequence in array: NOR OneNAND NAND Signed-off-by:
-
Vimal Singh authored
Introducing 'gpmc-nand.c' for GPMC specific NAND init. For example: GPMC timing parameters and all. This patch also migrates gpmc related calls from 'nand/omap2.c' to 'gpmc-nand.c'. Signed-off-by:
-
vikram pandita authored
No logical code change Fix coding style indentaion as per checkpatch.pl Fix multi-line comment style reported by Nishanth Menon Signed-off-by:
Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by:
-
