Conflicts:
	drivers/net/benet/be_main.c

Commit 1018b5c0

 ("Set rt->rt_iif more
sanely on output routes.")  breaks rt_is_{output,input}_route.

This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0".

To fix it, this does:

1) Add "int rt_route_iif;" to struct rtable

2) For input routes, always set rt_route_iif to same value as rt_iif

3) For output routes, always set rt_route_iif to zero.  Set rt_iif
   as it is done currently.

4) Change rt_is_{output,input}_route() to test rt_route_iif

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit c6e1a0d1

 broken the calc
 (net: Allow no-cache copy from user on transmit)
of checksum, which may cause some tcp packets be dropped because
incorrect checksum. ssh does not work under today's net-next-2.6
tree.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ethtool infrastructure for blinking, which is now does
locking at higher level.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert driver to use new ethtool set_phys_id.
Not completely sure that this is correct for all cases of device
up/down and doing operation. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather simple conversion to hw_features.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

udev fully replaces this special file system that only contains CAPI
NCCI TTY device nodes. User space (pppdcapiplugin) works without
noticing the difference.

Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes error from sparse:
  CHECK   drivers/net/xen-netback/xenbus.c
drivers/net/xen-netback/xenbus.c:29:40: error: dubious one-bit signed bitfield

        int have_hotplug_status_watch:1;

Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

eq_next_idx is not getting reset to zero during suspend.
This causes resume to fail. Added the fix.

Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Renamed msix_vec_idx to eq_idx in be_eq_obj struct.
Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure.
These members are used in INTX mode also.

Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert to new ethtool set physical id model. Remove no longer used
timer, and fix docbook comment.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also cleanup error codes to no lie about things that driver doesn't
support. If device is down report -EAGAIN (same as Broadcom), and
if port doesn't blink then error as well.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In this case, need to add element to device private to hold
original led state.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also fix up incorrect docbook comment

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement new ethtool set_phys_id on Chelsio cxgb3 board.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement control of LED via set_phys_id.
Note: since PHY is powered off if device is down, this board
only allows blinking if device is up.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement set_phys_id led control on SysKonnect board.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ethtool set_phys_id to control LED. Fixes issues with RTNL being
held for extended periods.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

otherwise we loop forever if a PPPoE socket was set
to PPPOX_ZOMBIE state by a PADT message when the
ethernet device is going down afterwards.

Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6085 is identical to the mv88e6095, except that all ports are
10/100 Mb/s, so use the existing setup code except for the cpu/dsa speed
selection in _setup_port().

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

properly record sk_rxhash in ipv6 sockets (v2)

Noticed while working on another project that flows to sockets which I had open
on a test systems weren't getting steered properly when I had RFS enabled.
Looking more closely I found that:

1) The affected sockets were all ipv6
2) They weren't getting steered because sk->sk_rxhash was never set from the
incomming skbs on that socket.

This was occuring because there are several points in the IPv4 tcp and udp code
which save the rxhash value when a new connection is established.  Those calls
to sock_rps_save_rxhash were never added to the corresponding ipv6 code paths.
This patch adds those calls.  Tested by myself to properly enable RFS
functionalty on ipv6.

Change notes:
v2:
	Filtered UDP to only arm RFS on bound sockets (Eric Dumazet)

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bumped up version number to 5.0.16

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o In dev->open LRO was enabled by default, enable it depending
  upon netdev->features , kernel may have disabled it.
o Configure LRO when interface is up.

Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <Anirban.Chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use flash layout table to get flash fw starting address and its size.
If that fails, use legacy method.

Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleaned up unused codes for interrupt coalescence settings

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Made changes to VLAN code comply with new VLAN infrastructure in kernel

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Optimized code resulted in achieving lower CPU utilization on transmit path
and higher throughput for small packet sizes (64 bytes).

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

 1. Changed adapter structure to move away from embedding hardware and
    receive context structs and use pointers to those objects
 2. Packed all the structs that interface with FW
 3. Removed unused code and structs

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a memory leak in error path of pci info.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this fix, PCI info was available only when multiple NIC functions
are present on the same port.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

adapter could remain uninitialized if probe fails for some reason.
A null pointer access could cause a crash if be_shutdown
is called after that.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch contains a fix for gracefully handling firmware heartbeat
failure instead of forcing panic.

Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes spin_locks at CAN socket creation time by using RCU.

Inspired by the discussion with Kurt van Dijck and Eric Dumazet the RCU code
was partly derived from af_phonet.c

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an interrupt occurs, the INT pin is driven low by the
MCP251x controller (falling edge) but in some cases the INT
pin can be connected to the MPU through a transistor or level
translator which inverts this signal. In this case interrupt
should be configured in rising edge.

This patch adds support to pass the IRQ flags via
mcp251x_platform_data.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>