- Feb 05, 2022
-
-
Douglas Anderson authored
The two nodes were mis-sorted. Reorder. This is a no-op change. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220202132301.v3.6.I874c6f2a62b7922a33e10d390a8983219a76250b@changeid
-
Douglas Anderson authored
Specifying "input-enable" on a MSM GPIO is a no-op for the most part. The only thing it really does is to explicitly force the output of a GPIO to be disabled right at the point of a pinctrl transition. We don't need to do this and we don't typically specify "input-enable" unless there's a good reason to. Remove it. Signed-off-by:
-
Douglas Anderson authored
This patch makes a few improvements to the way that sdc1 / sdc2 pinctrl is specified on sc7280: 1. There's no reason to "group" the sdc pins into one overarching node and there's a downside: we have to replicate the hierarchy in the board device tree files. Let's clean this up. 2. There's really not a lot of reason not to list the "pinctrl" for sdc1 (eMMC) in the SoC dtsi file. These aren't GPIO pins and everyone's going to specify the same pins. 3. Even though it's likely that boards will need to override pinctrl for sdc2 (SD card) to add the card detect GPIO, we can be symmetric and add it to the SoC dsti file. 4. Let's get rid of the word "on" from the normal config and add a "sleep" suffix to the sleep config. This looks cleaner to me. This is intended to be a no-op change but it could plausibly change behavior depending on how the pinctrl code parses things. One thing to note is that "SD card detect" is explicitly listed now as keeping its pull enabled in sleep since we still want to detect card insertions even if the controller is suspended (because no card is inserted). The pinctrl framework likely did this anyway, but it's nice to see it explicit. Signed-off-by:
-
Douglas Anderson authored
The sdc1 / sdc2 pinctrl lines were randomly stuffed in the middle of the qup pinctrl lines. Sort them properly. This is a no-op change. Just code movement. Signed-off-by:
-
Douglas Anderson authored
Some of the fixed regulators were missing the "-regulator" suffix. Add it to be consistent within the file and consistent with the fixed regulators in sc7180-trogdor. Signed-off-by:
-
Douglas Anderson authored
All of the other fixed regulators have the "-regulator" suffix. Add it to pp3300_hub to match. Signed-off-by:
-
Bjorn Andersson authored
Enable the audio, compute, sensor and modem remoteproc and specify firmware path for these on the Qualcomm SM8450 QRD. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220128025513.97188-14-bjorn.andersson@linaro.org
-
Bjorn Andersson authored
The Qualcomm SM8450 carries the familiar set of audio, compute, sensor and modem remoteprocs. Add these and their dependencies. Signed-off-by:
-
- Feb 04, 2022
-
-
Alex Elder authored
At least three platforms require the "qcom,qmp" property to be specified, so the IPA driver can request register retention across power collapse. Update DTS files accordingly. Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
- Feb 01, 2022
-
-
Alexander Martinz authored
Add initial support for the SHIFT SHIFT6mq (axolotl) based on the sdm845-mtp DT. Currently supported features: * Buttons (power, volume) * Bluetooth, DSPs and modem * Display and GPU * Touch * UART * USB peripheral mode * WLAN Co-developed-by:
Caleb Connolly <caleb@connolly.tech> Signed-off-by:
Alexander Martinz <amartinz@shiftphones.com> Signed-off-by:
-
Caleb Connolly authored
The OnePlus 6 and 6T feature a BQ27411 fuel gauge for reading the battery stats. Enable it and add a simple battery to document the battery specs of each device. Signed-off-by:
-
Baruch Siach authored
Reference clock period for rate of 24MHz is 41ns (0x29). Link: https://lore.kernel.org/r/1965fc315525b8ab26cf9f71f939c24d@codeaurora.org Link: https://lore.kernel.org/r/a1932eba-564c-fe32-f220-53aa75250105@seco.com Fixes: 20bb9e3d ("arm64: dts: qcom: ipq6018: add usb3 DT description") Reported-by:
Kathiravan T <kathirav@codeaurora.org> Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
-
Petr Vorel authored
to follow the naming convention used by other DTS files. Signed-off-by:
Petr Vorel <petr.vorel@gmail.com> Signed-off-by:
-
Petr Vorel authored
This is needed due changes in commit 0519d1d0 ("clk: qcom: gcc-msm8994: Modernize the driver"), which removed struct clk_fixed_factor. Preparation for next commit for enabling SD/eMMC. Inspired by 2c2f64ae. This is required for both msm8994-huawei-angler (sdhc1 will be enabled in next commit) and msm8992-lg-bullhead (where actually fixes sdhc1 - tested on bullhead rev 1.01). Fixes: 0519d1d0 ("clk: qcom: gcc-msm8994: Modernize the driver") Signed-off-by:
-
Manivannan Sadhasivam authored
Fix the MSI IRQ used for PCIe instances 1 and 2. Cc: stable@vger.kernel.org Fixes: e53bdfc0 ("arm64: dts: qcom: sm8250: Add PCIe support") Reported-by:
Jordan Crouse <jordan@cosmicpenguin.net> Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by:
-
Maulik Shah authored
This change updates/corrects below cpuidle parameters 1. entry-latency, exit-latency and residency for various idle states. 2. arm,psci-suspend-param which is same for CLUSTER_SLEEP_0/1 states. 3. Add CLUSTER_SLEEP_1 in CLUSTER_PD. Cc: devicetree@vger.kernel.org Fixes: 5188049c ("arm64: dts: qcom: Add base SM8450 DTSI") Signed-off-by:
Maulik Shah <quic_mkshah@quicinc.com> Reviewed-by:
Ulf Hansson <ulf.hansson@linaro.org> [bjorn: Split domain-idle-states, per Ulf's request] Signed-off-by:
-
Maulik Shah authored
Correct the TCS config by updating the number of TCSes for each type. Cc: devicetree@vger.kernel.org Fixes: b7e8f433 ("arm64: dts: qcom: Add basic devicetree support for SM8350 SoC") Signed-off-by:
-
Maulik Shah authored
This change adds various idle states and add devices to power domains. Cc: devicetree@vger.kernel.org Signed-off-by:
-
Maulik Shah authored
Correct the TCS config by updating the number of TCSes for each type. Cc: devicetree@vger.kernel.org Fixes: d8cf9372 ("arm64: dts: qcom: sm8150: Add apps shared nodes") Signed-off-by:
-
Kathiravan T authored
On IPQ8074, 4MB of memory is needed for TZ. So mark that region as reserved. Signed-off-by:
Kathiravan T <quic_kathirav@quicinc.com> [bjorn: Squash with existing reserved-memory node] Signed-off-by:
-
Robert Marko authored
IPQ8074 uses SMEM like other modern QCA SoC-s, so since its already supported by the kernel add the required DT nodes. Signed-off-by:
Robert Marko <robimarko@gmail.com> Signed-off-by:
-
Thara Gopinath authored
Add LMh nodes for cpu cluster0 and cpu cluster1 for sm8150 SoC. Signed-off-by:
Thara Gopinath <thara.gopinath@linaro.org> Reviewed-by:
-
Petr Vorel authored
Fixes: bd943653 ("arm64: dts: qcom: Add device tree for Samsung J5 2015 (samsung-j5)") Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
-
Marijn Suijten authored
This reverts commit c23f1b77 . The SM6125_VDDCX constant was replaced with 0 temporarily as the header patch defining this constant resided in a different branch, creating an unwanted dependency of the dts branch on the drivers branch. Now (by the time this patch will be applied) that both branches have been merged upstream, it is safe to revert to the constant again. Signed-off-by:
Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by:
-
David Heidelberg authored
qcom,init-seq registers are in pairs Signed-off-by:
David Heidelberg <david@ixit.cz> Signed-off-by:
-
Luca Weiss authored
WLED is used for controlling the display backlight on this phone, so configure the node and enable it. Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Signed-off-by:
-
Luca Weiss authored
WLED is used for controlling the backlight on some boards, add the node for it. Signed-off-by:
-
David Heidelberg authored
Follow common pattern for this device, first specific and then generic compatible. Signed-off-by:
-
Baruch Siach authored
Add the generic 'max-link-speed' property to describe the IPQ6018 PCIe link generation limit. This allows the generic dwc code to configure the link speed correctly. Signed-off-by:
Baruch Siach <baruch.siach@siklu.com> Signed-off-by:
-
Petr Vorel authored
Signed-off-by:
-
Petr Vorel authored
Signed-off-by:
-
Vladimir Zapolskiy authored
The change adds SM8250 cpufreq-epss controller interrupts for each CPU core cluster. Signed-off-by:
Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Cc: Thara Gopinath <thara.gopinath@linaro.org> Signed-off-by:
-
David Heidelberg authored
dt-schema expect to have fallback compatible, which is now in-place. Fixes warning generated by `make qcom/sdm845-oneplus-fajita.dtb`: arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: power-controller@c300000: compatible: ['qcom,sdm845-aoss-qmp'] is too short From schema: Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.yaml Signed-off-by: -
David Heidelberg authored
QCOM BAM parses property `qcom,controlled-remotely` as a boolean, adjust dts to reflect that. Discovered while converting text documentation into yaml format. Signed-off-by:
-
Rob Herring authored
The msm8998 cache nodes have some issues. First, L1 caches are described within cpu nodes, not as separate nodes. The 'next-level-cache' property is of course in the correct location, otherwise the cache hierarchy walking would not work. Remove all the L1 cache nodes. Second, 'arm,arch-cache' is not a documented compatible string. "cache" is a sufficient compatible string for the Arm architected caches. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Felipe Balbi authored
Since commit d0a6ce59 ("arm64: dts: qcom: sm8150: Add support for SONY Xperia 1 / 5 (Kumano platform)"), we can directly refer to pwrkey and resin by their new labels, respectively pon_pwrkey and pon_resin. Simplify microsof surface duo DTS by utilizing the new labels. Signed-off-by:
Felipe Balbi <felipe.balbi@microsoft.com> Signed-off-by:
-
Felipe Balbi authored
By listing relevant DMA channels for the various QUPv3 instances, we can work on adding support for DMA to the respective drivers. Signed-off-by:
-
David Heidelberg authored
Pure effort to avoid `make dtbs_check` warnings about memory@ nodes, which should have property device_type set to memory. Fixes warnings as: arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: memory@f5b00000: 'device_type' is a required property From schema: dtschema/schemas/memory.yaml Signed-off-by: -
Dmitry Baryshkov authored
Replace (unused) enable-gpio binding with schema-defined wake-gpios. The GPIO line is still unused, but at least we'd follow the defined schema. While we are at it, change perst-gpio property to follow the preferred naming schema (perst-gpios). Fixes: 13e948a3 ("arm64: dts: qcom: sm8250: Commonize PCIe pins") Cc: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by:
-
Stephan Gerhold authored
qcom,apq8016-sbc-sndcard is now covered by the qcom,sm8250.yaml schema which has slightly different recommendations for the naming of properties and nodes. The old naming is still functional but deprecated. Update the &sound node in apq8016-sbc to fix the following dtbs_check warnings: apq8016-sbc.dt.yaml: sound@7702000: 'model' is a required property From schema: sound/qcom,sm8250.yaml apq8016-sbc.dt.yaml: sound@7702000: 'external-dai-link@0', ... do not match any of the regexes: '.*-dai-link$', ... From schema: sound/qcom,sm8250.yaml Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
-
