Callers may stop the SSP core requesting the interrupt so it can't be
freed unconditionally.  Also use NO_IRQ like we should.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.

This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.

CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:

    a. _only_ PXA300/PXA310 support included and no L2 cache wanted
    b. PXA320 support included, but want L2 be disabled

So the enabling of L2 depends on two things:

    - CACHE_XSC3L2 is selected
    - and L2 cache is present

Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).

IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.

Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:

   - OC bits in TTBASE register (table walk outer cache attributes)
   - LLR Outer Cache Attributes (OC) in Auxiliary Control Register

Signed-off-by: Lothar WaÃ&lt;9f&gt;mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

     And also reserve 32 IRQs for the two GPIO expanders.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

A pxa3xx_set_nand_info() is also introduced to set the PXA3xx NAND
driver specific platform_data structure pointer.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

So processor specific clock sources can be defined in pxa300.c
and pxa320.c.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some boards want to change low power state of pins on-the-fly, this
function helps to facilitate that operation instead of switching
back-n-forth between two configurations with pxa2xx_mfp_config().

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

pxa320_init_mfp() is simple enough to be embedded into pxa320_init()
to simplify the code a bit.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some boards use UART other than FFUART for the console, E.g. Marvell
PXA3xx Form Factor Platform (aka Littleton) uses STUART. This patch
modifies the uncompress.h so that display of the uncompress message
is routed to the STUART.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Setting PKWR bits on those pins will make the resuming from
low power state to fail.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The correct macro name when a driver is built as a module is
CONFIG_*_MODULE instead of CONFIG_*_MODULES. This patch fixes
this in several places.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

	unnecessary menu level

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add a function to dynamically allocate and register pxa2xx-spi platform
devices, to be used by PXA2xx and PXA3xx based systems. Switch pcm027 and
lubbock to use it.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The Zylonite has an AC97 subsystem on it so register the AC97 controller
device.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As well as moving all the device declarations to a single one in devices.c
this causes all platforms to register the I/O and interrupt resources for
the AC97 controller.

Cc: eric miao <eric.miao@marvell.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Jürgen Schindele <linux@schindele.name>
Cc: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The pxa2xx_udc.c driver is renamed to pxa25x_udc.c (the platform
driver name changes from pxa2xx-udc to pxa25x-udc) and the
platform driver name of pxa27x_udc.c is fixed to pxa27x-udc.
pxa_device_udc in devices.c is split into pxa25x and pxa27x flavors
and the pxa27x_device_udc is enabled in pxa27x.c.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Including from Ian Molton:

Fixes for mistakes left over from the PXA2{5,7}X UDC split.

Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

	is handled in board code

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Provide a set of functions to control state of pins dedicated to IrDA.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

pxa_set_cken() is now unused, remove it.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We need to support more than one name+device for a struct clk for a
small number of peripherals.  We do this by re-using struct clk alias
to another struct clk - IOW, if we find that the entry we're using is
an alias, we return the aliased entry not the one we found.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Warn people when using pxa2xx-gpio.h as it is only here for backwards
compatibility. The new mfp-pxa2[57]x.h and the relevant API should be used
instead.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Both i2c-pxa.c and irq.c still include pxa2xx-gpio.h although is is not
needed anymore.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds exit and remove handlers to pxafb so that it can be loaded
and unloaded as a module.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

PCM990 boards can be assembled with either a Sharp STN or a NEC TFT LCD. This
patch adds support for these displays and for the backlight, using the pwm_bl
driver.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

magician has a GPIO that modifies the brightness level additionally to
the PWM duty value. This patch makes use of the pwm_bl notify callback
to present userspace with a single brightness scale.
This gets rid of the pxa_set_cken calls and direct PWM register access.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Make the return of pwm_request() be more informative than just
being NULL on error by using PTR_ERR() to respond with an
approriate error.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This allows platform code to manipulate GPIOs and brightness level as
needed.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch mostly by Eric Miao, minor edits by rmk.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>