- Jun 09, 2014
-
-
James Bottomley authored
-
- Jun 02, 2014
-
-
Fabian Frederick authored
__constant_cpu_to_be16 converted to cpu_to_be16 This patch fixes checkpatch warnings: "WARNING: __constant_cpu_to_be16 should be cpu_to_be16" Signed-off-by:
Fabian Frederick <fabf@skynet.be> Ack-by:
Boaz Harrosh <bharrosh@panasas.com> Signed-off-by:
Christoph Hellwig <hch@lst.de>
-
Ben Hutchings authored
Matt Taggart reported that mvsas didn't bind to the Marvell SAS controller on a Supermicro AOC-SAS2LP-MV8 board. lspci reports it as: 01:00.0 RAID bus controller [0104]: Marvell Technology Group Ltd. Device [1b4b:9485] (rev 03) Subsystem: Marvell Technology Group Ltd. Device [1b4b:9485] [...] Add it to the device table as chip_9485. Signed-off-by:Ben Hutchings <ben@decadent.org.uk> Reported-by:
Matt Taggart <taggart@debian.org> Tested-by:
Jan "Yenya" Kasprzak <kas@fi.muni.cz> Signed-off-by:
-
Christoph Hellwig authored
This reverts commit 11206081. Based on comments from Mike Christie and Sony John-N.
-
- May 29, 2014
-
-
Tomas Henzl authored
Hi, without this patch the istwiRWRequest->MsgContext is always set to zero, this patch saves the MsgContext in a msgcontext variable and then restores the value. Thanks to David Jeffery who found the issue and did the analysis. Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Acked-by:
Desai, Kashyap <Kashyap.Desai@lsi.com> Signed-off-by:
-
Paul Bolle authored
The acornscsi driver was added in v2.1.88. It has always #undef-ed CONFIG_SCSI_ACORNSCSI_LINK near the top of acornscsi.c. And, just to be sure, it has also always triggered a preprocessor error if CONFIG_SCSI_ACORNSCSI_LINK was still defined. But, as far as I can see, it has never even been possible to set SCSI_ACORNSCSI_LINK through kconfig, or its predecessors, in the first place. Let's remove the code involved. Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Acked-by:
Russell King <rmk+kernel@arm.linux.org.uk> Acked-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Finn Thain authored
This is the delta between the two submissions: [PATCH 00/12] scsi/NCR5380: fix debugging macros and #include structure and [PATCH v2 00/12] scsi/NCR5380: fix debugging macros and #include structure The macro definition changes were discussed on the mailing list during review. The idea is to get the compiler to check the parameters of disabled printk() calls so that the debugging code doesn't rot again. Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
-
Matthew Wilcox authored
Removing the host_lock from the I/O submission path gives a huge scalability improvement. Signed-off-by:
Matthew Wilcox <matthew.r.wilcox@intel.com> Reviewed-by:
Nicholas Bellinger <nab@linux-iscsi.org> Reviewed-by:
Praveen Krishnamoorthy <Praveen.krishnamoorthy@lsi.com> Acked-by:
Sreekanth Reddy <Sreekanth.reddy@lsi.com> Signed-off-by:
-
Matthew Wilcox authored
Reusing a msg frame quickly means it's still cache-hot. This yields a small but noticable performance improvement in a well-known database benchmark. This improvement is already present in the mpt3sas driver. Signed-off-by:
-
Matthew Wilcox authored
Reusing a smid quickly means it's still cache-hot. This yields a small but noticable performance improvement in a well-known database benchmark. This improvement is already present in the mpt3sas driver. Signed-off-by:
-
Matthew Wilcox authored
Removing the host_lock from the I/O submission path gives a huge scalability improvement. Signed-off-by:
-
Matthew Wilcox authored
The mpt2sas_scsih_issue_tm() function does not use the 'serial_number' argument passed to it. Removing it removes the last vestiges of the scsi_cmnd's serial_number field from this driver. Signed-off-by:
-
Matthew Wilcox authored
Removing the host_lock from the I/O submission path gives a huge scalability improvement. Signed-off-by:
-
Matthew Wilcox authored
The mpt3sas_scsih_issue_tm() function does not use the 'serial_number' argument passed to it. Removing it removes the last vestiges of the scsi_cmnd's serial_number field from this driver. Signed-off-by:
-
Benoit Taine authored
This issue was reported by coccicheck using the semantic patch at scripts/coccinelle/api/memdup.cocci Signed-off-by:
Benoit Taine <benoit.taine@lip6.fr> Acked-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Benoit Taine authored
This issue was reported by coccicheck using the semantic patch at scripts/coccinelle/api/memdup.cocci Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
-
Dan Carpenter authored
There are missing curly braces here so it prints that the recovery failed even when it succeeded. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Acked-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Jayamohan Kallickal authored
Bumping the driver version. Signed-off-by:
John Soni Jose <sony.john-n@emulex.com> Signed-off-by:
Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by:
-
Jayamohan Kallickal authored
During heavy IO in multipath environment with many active sessions and port-bouncing happening, there is a race condition because of which beiscsi_prcess_cqe() gets called for a connection whose endpoint is freed. Checking endpoint reference for a connection before processing in beiscsi_process_cq(). Signed-off-by:
Minh Tran <minhduc.tran@emulex.com> Signed-off-by:
-
Jayamohan Kallickal authored
EQ teardown should happen only after all CQ are destroyed. In some FW config, adapter goes into a freeze state. This fix moves teardown of MCC-Q before the EQ teardown happens. Signed-off-by:
-
Jayamohan Kallickal authored
From: Dan Carpenter [mailto:dan.carpenter@oracle.com] Sent: Friday, March 28, 2014 1:42 AM Subject: re: [SCSI] be2iscsi: Fix handling timed out MBX completion from FW Hello Jayamohan Kallickal, The patch 1957aa7f : "[SCSI] be2iscsi: Fix handling timed out MBX completion from FW" from Jan 29, 2014, leads to the following static checker warning: drivers/scsi/be2iscsi/be_main.c:5581 beiscsi_dev_probe() error: memset() '&phba->ctrl.ptag_state[i]->tag_mem_state' too small (24 vs 32) drivers/scsi/be2iscsi/be_main.c 5576 for (i = 0; i < MAX_MCC_CMD; i++) { 5577 init_waitqueue_head(&phba->ctrl.mcc_wait[i + 1]); 5578 phba->ctrl.mcc_tag[i] = i + 1; 5579 phba->ctrl.mcc_numtag[i + 1] = 0; 5580 phba->ctrl.mcc_tag_available++; 5581 memset(&phba->ctrl.ptag_state[i].tag_mem_state, 0, 5582 sizeof(struct beiscsi_mcc_tag_state)); ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Probably this this be change to sizeof(struct be_dma_mem struct)? It looks like we are corrupting memory a bit here. 5583 } regards, dan carpenter Reported-by:
-
Jayamohan Kallickal authored
SKH-R adapter, TCP Window Size/Scale parameters are passed in TCP Connection Offload Mbx Command. Signed-off-by:
-
Jayamohan Kallickal authored
Signed-off-by:
-
Jayamohan Kallickal authored
Before probe for function was completed, iSCSI Daemon had initiated login to target while OS was coming up. The targets which had node.startup=automatic, login process was initiated.Since function specific initialization was still in progress this lead to kernel panic. Fixed the issue by moving iscsi_host_add() call after adapter initialization is done. Signed-off-by:
-
Jayamohan Kallickal authored
Getting WRB for MCCQ posting was done before looking if tag is available or not. This lead to increase phba->ctrl.mcc_obj.q.used variable and the WARN_ON message was coming from wrb_from_mccq(). Moved getting wrb from mccq after checking for the tag. In wrb_from_mccq(), memset is done before returning wrb ptr. Removed memset of mccq wrb from all other functions. Signed-off-by:
-
- May 28, 2014
-
-
Sujit Reddy Thumma authored
Error handling in UFS driver is broken and resets the host controller for fatal errors without re-initialization. Correct the fatal error handling sequence according to UFS Host Controller Interface (HCI) v1.1 specification. o Processed requests which are completed w/wo error are reported to SCSI layer and any pending commands that are not started are aborted in the controller and re-queued into scsi mid-layer queue. o Upon determining fatal error condition the host controller may hang forever until a reset is applied. Block SCSI layer for sending new requests and apply reset in a separate error handling work. o SCSI is informed about the expected Unit-Attention exception from the device for the immediate command after a reset so that the SCSI layer take necessary steps to establish communication with the device. Signed-off-by:
Sujit Reddy Thumma <sthumma@codeaurora.org> Reviewed-by:
Yaniv Gardi <ygardi@codeaurora.org> Tested-by:
Dolev Raviv <draviv@codeaurora.org> Acked-by:
Vinayak Holikatti <vinholikatti@gmail.com> Signed-off-by:
-
Sujit Reddy Thumma authored
As of now SCSI initiated error handling is broken because, the reset APIs don't try to bring back the device initialized and ready for further transfers. In case of timeouts, the scsi error handler takes care of handling aborts and resets. Improve the error handling in such scenario by resetting the device and host and re-initializing them in proper manner. Signed-off-by:
-
Sujit Reddy Thumma authored
There is a possible race condition in the hardware when the abort command is issued to terminate the ongoing SCSI command as described below: - A bit in the door-bell register is set in the controller for a new SCSI command. - In some rare situations, before controller get a chance to issue the command to the device, the software issued an abort command. - If the device recieves abort command first then it returns success because the command itself is not present. - Now if the controller commits the command to device it will be processed. - Software thinks that command is aborted and proceed while still the device is processing it. - The software, controller and device may go out of sync because of this race condition. To avoid this, query task presence in the device before sending abort task command so that after the abort operation, the command is guaranteed to be non-existent in both controller and the device. Signed-off-by:
-
Sujit Reddy Thumma authored
Currently, sending Task Management (TM) command to the card might be broken in some scenarios as listed below: Problem: If there are more than 8 TM commands the implementation returns error to the caller. Fix: Wait for one of the slots to be emptied and send the command. Problem: Sometimes it is necessary for the caller to know the TM service response code to determine the task status. Fix: Propogate the service response to the caller. Problem: If the TM command times out no proper error recovery is implemented. Fix: Clear the command in the controller door-bell register, so that further commands for the same slot don't fail. Problem: While preparing the TM command descriptor, the task tag used should be unique across SCSI/NOP/QUERY/TM commands and not the task tag of the command which the TM command is trying to manage. Fix: Use a unique task tag instead of task tag of SCSI command. Problem: Since the TM command involves H/W communication, abruptly ending the request on kill interrupt signal might cause h/w malfunction. Fix: Wait for hardware completion interrupt with TASK_UNINTERRUPTIBLE set. Signed-off-by: -
Sujit Reddy Thumma authored
Make undeclared functions static and declare exported symbols to suppress warnings from sparse tool. Signed-off-by:
-
Sujit Reddy Thumma authored
Fix many warnings with incorrect endian assumptions which makes the code unportable to new architectures. The UFS specification defines the byte order as big-endian for UPIU structure and little-endian for the host controller transfer/task management descriptors. Signed-off-by:
-
Joe Handzik authored
rescan_hba_mode was defined as a u8 so could never be less than zero: rescan_hba_mode = hpsa_hba_mode_enabled(h); if (rescan_hba_mode < 0) goto out; Signed-off-by:Joe Handzik <joseph.t.handzik@hp.com> Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Reported-by:
-
Finn Thain authored
The sun3 drivers suffer from a whole bunch of duplicated code. Fix this by following the g_NCR5380_mmio example. (Notionally, sun3_scsi relates to sun3_scsi_vme in the same way that g_NCR5380 relates to g_NCR5380_mmio.) Dead code is also removed: we now have working debug macros so SUN3_SCSI_DEBUG is undesirable. Dead code within #ifdef OLD_DMA is also dropped, consistent with sun3_scsi_vme.c. Signed-off-by:
Sam Creasey <sammy@sammy.net> Signed-off-by:
-
Finn Thain authored
Move the #include "NCR5380.h" out of the sun3_scsi.h header file and into the driver .c files, like all the other NCR5380 drivers in the tree. This improves uniformity and reduces the depth of nested includes. The sequence of #include's, #define's and #if's no longer does my head in. Signed-off-by:
-
Finn Thain authored
Remove the unused (and divergent) debugging macro definitions from the sun3_NCR5380 and atari_NCR5380 drivers. These drivers have been converted to use the common macros in NCR5380.h. Signed-off-by:
Michael Schmitz <schmitz@debian.org> Signed-off-by:
-
Finn Thain authored
All three NCR5380 core driver implementations share the same NCR5380.h header file so they need to agree on certain macro definitions. The flag bit used by the NDEBUG_MERGING macro in atari_NCR5380 and sun3_NCR5380 collides with the bit used by NDEBUG_LISTS. Moreover, NDEBUG_ABORT appears in NCR5380.c so it should be defined in NCR5380.h rather than in each of the many drivers using that core. An undefined NDEBUG_ABORT macro caused compiler errors and led to dodgy workarounds in the core driver that can now be removed. (See commits f566a576 and 185a7a1c .) Move all of the NDEBUG_ABORT, NDEBUG_TAGS and NDEBUG_MERGING macro definitions into NCR5380.h where all the other NDEBUG macros live. Also, incorrect "#ifdef NDEBUG" becomes "#if NDEBUG" to fix the warning: drivers/scsi/mac_scsi.c: At top level: drivers/scsi/NCR5380.c:418: warning: 'NCR5380_print' defined but not used drivers/scsi/NCR5380.c:459: warning: 'NCR5380_print_phase' defined but not used The debugging code is now enabled when NDEBUG != 0. Signed-off-by:
-
Finn Thain authored
All NCR5380 drivers already include the NCR5380.h header. Better to adopt those macros rather than have three variations on them. Moreover, the macros in NCR5380.h are preferable because the atari_NCR5380 and sun3_NCR5380 versions are inflexible. For example, they can't accomodate dprintk(NDEBUG_MAIN | NDEBUG_QUEUES, ...) Replace the *_PRINTK macros from atari_NCR5380.h and sun3_NCR5380.h with the equivalent macros from NCR5380.h. Signed-off-by:
-
Finn Thain authored
All NCR5380 drivers already include the NCR5380.h header. Better to adopt those macros rather than have three variations on them. Moreover, the macros in NCR5380.h are preferable anyway: the atari_NCR5380 and sun3_NCR5380 versions are inflexible. For example, they can't accomodate NCR5380_dprint(NDEBUG_MAIN | NDEBUG_QUEUES, ...) Replace the NCR_PRINT* macros from atari_NCR5380.h and sun3_NCR5380.h with the equivalent macros from NCR5380.h. Signed-off-by:
-
Finn Thain authored
There are three implementations of the core NCR5380 driver and three sets of debugging macro definitions. And all three implementations use the NCR5380.h header as well. Two of the definitions of the dprintk macro accept a variable argument list whereas the third does not. Standardize on the variable argument list. Signed-off-by:
-
Finn Thain authored
The change from cmd->target to cmd->device->id was apparently the purpose of commit a7f251228390e87d86c5e3846f99a455517fdd8e in kernel/git/tglx/history.git but some instances have been missed. Also fix the "NDEBUG_LAST_WRITE_SENT" and "NDEBUG_ALL" typo's. Also fix some format strings (%ul becomes %lu) that caused compiler warnings. Signed-off-by:
-
