Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The pinctrl properties on the IOMUXC node get overwritten by the
carrier board level device tree, hence the pinctrl_reset_moci
pinctrl does not get applied.

Associate the pinctrl_reset_moci pinctrl with the PCIe node where
we also make use of the pin as a reset GPIO.

Since the pin is muxed as a GPIO by default not muxing it explicitly
worked fine in practise.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is no need to keep the PMU disabled.

Enable it like it is done in the other i.MX dtsi files.

With this change applied we see:

[    1.338866] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add egalax touch screen support on i2c2 bus.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX6QDL SabreAuto board's gpio keys support, there
are 5 gpio keys on base board:

SW3: KEY_HOME;
SW4: KEY_BACK;
SW5: KEY_PROGRAM;
SW6: KEY_VOLUMEUP;
SW7: KEY_VOLUMEDOWN;

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The board typically has 2 populated SFF interfaces. The mv88e6xxx
driver currently supports SFF modules connected to ports 9 and 10 of
the mv88e6390. Add support for sff2, which is connected to port 9.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The switch has an SFF attached to port 5. Add the SFF device, the
pinmux for its GPIOs, and list the port in the switch configuration.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update i.MX6ULL iomux header according to latest reference
manual Rev.1, 11/2017.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable cpuidle for i.MX7S/D using generic ARM cpuidle
driver, below 2 idle states enabled:

1. ARM WFI;
2. SoC WAIT mode.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch enables i.MX6SX SDB board's below GPIO buttons
as wakeup sources:

SW4(FUNC1): KEY_VOLUMEUP
SW5(FUNC2): KEY_VOLUMEDOWN

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch enables i.MX7D SDB board's below GPIO buttons
as wakeup sources:

S1(FUNC1): KEY_VOLUMEUP
S3(FUNC2): KEY_VOLUMEDOWN

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease
license compliance management.

Signed-off-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

NOR and IFC controller connectivity is big-endian.
So add big-endian field in nor device tree node allowing
IFC controller to read/write data from/to the flash correctly.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds missing compatible for i.MX boards.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6ULL is a lite version of i.MX6UL, its full name
is i.MX6 UltraLiteLite, NOT UlltraLite.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6SLL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add weim node for i.MX6UL SOC.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:

imx6ul-imx6ull-board.dtsi:
 ...
 pinctrl_uart5: uart5grp {
	fsl,pins = <
		MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX   0x1b0b1
	 	MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX   0x1b0b1
 	 >;
 };

imx6ul-board.dts:
 #include <imx6ul.dtsi>
 #include <imx6ul-imx6ull-board.dtsi>
 ...

imx6ull-board.dts:
 #include <imx6ull.dtsi>
 #include <imx6ul-imx6ull-board.dtsi>
 ...

Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Setting a stdout-path in the .dtb is convenient because then the user
gets a serial console on the RS-232 connector without any extra effort
of figuring out the relevant 'console=' boot parameter.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The WaRP7 has one mikroBUS socket on the back to plug click boards.
This patch allows to interact with some of these
i2c modules (EEPROM, RTC and so on).

Signed-off-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The "EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation" is based on the 1.5 version
of the i.Core MX6 cpu module. The 1.5 version differs from the original one for
a few details, including the ethernet PHY interface clock provider.

With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver

While before using the 1.5 version, ethernet failed to startup do to un-clocked
PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY

Fixes: 3fe08835

 ("ARM: dts: imx6q: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 1.5 version of Engicam's i.Core MX6 CPU module features a different clock
provider for the ethernet's PHY interface. Adjust the FEC ptp clock to
reference CLK_ENET_REF clock source, and set SION bit of
MX6QDL_PAD_GPIO_16__ENET_REF_CLK to adjust the input path of that pin.

The newly introduced imx6ql-icore-1.5.dtsi allows to collect in a single
place differences between version '1.0' and '1.5' of the module.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Gives substantial performance improvement for transfers larger than 16
bytes (DMA_THRESHOLD).  Smaller transfers are unaffected.

Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use consistent pinctrl node names for Engicam dt files,
sufix 'grp' look consistent than actual node name

- pinctrl_gpmi_nand: gpmi-nand {
+ pinctrl_gpmi_nand: gpminandgrp {

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move usdhc2 and gpmi along with pinctrl nodes on
imx6ul-isiot.dtsi from dts files and mark it as 'disabled'
and the relevant dts will enable the status as 'okay'

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Also added Engicam Copyright on missing files.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

System poweroff is already supported by PSCI on i.MX7D,
remove "snvs_poweroff" node to avoid below debug message
from syscon-poweroff driver:

[    1.831414] syscon-poweroff 30370000.snvs:snvs-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff
[    1.841707] syscon-poweroff: probe of 30370000.snvs:snvs-poweroff failed with error -16

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Define the Messaging Unit (MU) for i.MX7 in the processor's dtsi.
The respective driver is added in the next commit.

Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX7ULP B0 chip has some pin changes for USB and VIU
module, update pinfunc header file accordingly.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The MC13892 Analog-to-Digital input pins (ADIN5-7) are exposed on the
imx51-babbage board.

Pass the "fsl,mc13xxx-uses-adc" property so that the MC13892 ADC
block can work.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX6SLL pinctrl driver, for details, please refer to
Documentation/devicetree/bindings/gpio/gpio.txt of "gpio-ranges"
property.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull devicetree updates from Rob Herring:
 "A couple of new helper functions in preparation for some tree wide
  clean-ups.

  I'm sending these new helpers now for rc2 in order to simplify the
  dependencies on subsequent cleanups across the tree in 4.20"

* tag 'devicetree-fixes-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: Add device_type access helper functions
  of: add node name compare helper functions
  of: add helper to lookup compatible child node

Pull ARM SoC fixes from Olof Johansson:
 "First batch of fixes post-merge window:

   - A handful of devicetree changes for i.MX2{3,8} to change over to
     new panel bindings. The platforms were moved from legacy
     framebuffers to DRM and some development board panels hadn't yet
     been converted.

   - OMAP fixes related to ti-sysc driver conversion fallout, fixing
     some register offsets, no_console_suspend fixes, etc.

   - Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.

   - Fixed 0755->0644 permissions on a newly added file.

   - Defconfig changes to make ARM Versatile more useful with QEMU
     (helps testing).

   - Enable defconfig options for new TI SoC platform that was merged
     this window (AM6)"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: defconfig: Enable TI's AM6 SoC platform
  ARM: defconfig: Update the ARM Versatile defconfig
  ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
  ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
  ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
  ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
  ARM: dts: imx23-evk: Convert to the new display bindings
  ARM: dts: imx23-evk: Move regulators outside simple-bus
  ARM: dts: imx28-evk: Convert to the new display bindings
  ARM: dts: imx28-evk: Move regulators outside simple-bus
  Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
  arm: dts: am4372: setup rtc as system-power-controller
  ARM: dts: omap4-droid4: fix vibrations on Droid 4
  bus: ti-sysc: Fix no_console_suspend handling
  bus: ti-sysc: Fix module register ioremap for larger offsets
  ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
  ARM: OMAP2+: Fix null hwmod for ti-sysc debug

Pull x86 fixes from Thomas Gleixner:
 "Speculation:

   - Make the microcode check more robust

   - Make the L1TF memory limit depend on the internal cache physical
     address space and not on the CPUID advertised physical address
     space, which might be significantly smaller. This avoids disabling
     L1TF on machines which utilize the full physical address space.

   - Fix the GDT mapping for EFI calls on 32bit PTI

   - Fix the MCE nospec implementation to prevent #GP

  Fixes and robustness:

   - Use the proper operand order for LSL in the VDSO

   - Prevent NMI uaccess race against CR3 switching

   - Add a lockdep check to verify that text_mutex is held in
     text_poke() functions

   - Repair the fallout of giving native_restore_fl() a prototype

   - Prevent kernel memory dumps based on usermode RIP

   - Wipe KASAN shadow stack before rewinding the stack to prevent false
     positives

   - Move the AMS GOTO enforcement to the actual build stage to allow
     user API header extraction without a compiler

   - Fix a section mismatch introduced by the on demand VDSO mapping
     change

  Miscellaneous:

   - Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pti: Fix section mismatch warning/error
  x86/vdso: Fix lsl operand order
  x86/mce: Fix set_mce_nospec() to avoid #GP fault
  x86/efi: Load fixmap GDT in efi_call_phys_epilog()
  x86/nmi: Fix NMI uaccess race against CR3 switching
  x86: Allow generating user-space headers without a compiler
  x86/dumpstack: Don't dump kernel memory based on usermode RIP
  x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember()
  x86/alternatives: Lockdep-enforce text_mutex in text_poke*()
  x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
  x86/irqflags: Mark native_restore_fl extern inline
  x86/build: Remove jump label quirk for GCC older than 4.5.2
  x86/Kconfig: Fix trivial typo
  x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
  x86/spectre: Add missing family 6 check to microcode check

Pull CPU hotplug fix from Thomas Gleixner:
 "Remove the stale skip_onerr member from the hotplug states"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Remove skip_onerr field from cpuhp_step structure

Pull core fixes from Thomas Gleixner:
 "A small set of updates for core code:

   - Prevent tracing in functions which are called from trace patching
     via stop_machine() to prevent executing half patched function trace
     entries.

   - Remove old GCC workarounds

   - Remove pointless includes of notifier.h"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Remove workaround for unreachable warnings from old GCC
  notifier: Remove notifier header file wherever not used
  watchdog: Mark watchdog touch functions as notrace

Fix the section mismatch warning in arch/x86/mm/pti.c:

WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte()
The function pti_clone_pgtable() references
the function __init pti_user_pagetable_walk_pte().
This is often because pti_clone_pgtable lacks a __init
annotation or the annotation of pti_user_pagetable_walk_pte is wrong.
FATAL: modpost: Section mismatches detected.

Fixes: 85900ea5

 ("x86/pti: Map the vsyscall page if needed")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/43a6d6a3-d69d-5eda-da09-0b1c88215a2a@infradead.org

Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omap variants against v4.19-rc1

These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.

There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.

And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.

* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap

:
  ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
  ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
  arm: dts: am4372: setup rtc as system-power-controller
  ARM: dts: omap4-droid4: fix vibrations on Droid 4
  bus: ti-sysc: Fix no_console_suspend handling
  bus: ti-sysc: Fix module register ioremap for larger offsets
  ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
  ARM: OMAP2+: Fix null hwmod for ti-sysc debug

Signed-off-by: Olof Johansson <olof@lixom.net>

In the __getcpu function, lsl is using the wrong target and destination
registers. Luckily, the compiler tends to choose %eax for both variables,
so it has been working so far.

Fixes: a582c540

 ("x86/vdso: Use RDPID in preference to LSL when available")
Signed-off-by: Samuel Neves <sneves@dei.uc.pt>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180901201452.27828-1-sneves@dei.uc.pt