- Mar 19, 2022
-
-
Dan Carpenter authored
This code has an uninitialized variable warning: drivers/bluetooth/btmtkuart.c:184 mtk_hci_wmt_sync() error: uninitialized symbol 'wc'. But it also has error paths which have memory leaks. Fixes: 8f550f55b155 ("Bluetooth: btmtkuart: rely on BT_MTK module") Signed-off-by:Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Niels Dossche authored
hci_le_conn_failed function's documentation says that the caller must hold hdev->lock. The only callsite that does not hold that lock is hci_le_conn_failed. The other 3 callsites hold the hdev->lock very locally. The solution is to hold the lock during the call to hci_le_conn_failed. Fixes: 3c857757 ("Bluetooth: Add directed advertising support through connect()") Signed-off-by:
Niels Dossche <dossche.niels@gmail.com> Signed-off-by:
-
Manish Mandlik authored
When an Advertisement Monitor is configured with SamplingPeriod 0xFF, the controller reports only one adv report along with the MSFT Monitor Device event. When an advertiser matches multiple monitors, some controllers send one adv report for each matched monitor; whereas, some controllers send just one adv report for all matched monitors. In such a case, report Adv Monitor Device Found event for each matched monitor. Signed-off-by:
Manish Mandlik <mmandlik@google.com> Reviewed-by:
Miao-chen Chou <mcchou@chromium.org> Signed-off-by:
-
Manish Mandlik authored
Clear already tracked devices on system resume. Once the monitors are reregistered after resume, matched devices in range will be found again. Signed-off-by:
-
Gavin Li authored
Callers pass msg->msg_flags as flags, which contains MSG_DONTWAIT instead of O_NONBLOCK. Signed-off-by:
Gavin Li <gavin@matician.com> Signed-off-by:
-
Christophe JAILLET authored
data.pid is set twice with the same value. Remove one of these redundant calls. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by:
-
Max Chou authored
Add the support for RTL8852B BT controller on USB interface. The necessary firmware file will be submitted to linux-firmware. Signed-off-by:
Max Chou <max.chou@realtek.com> Signed-off-by:
-
Pavel Skripkin authored
Syzbot hit general protection fault in __pm_runtime_resume(). The problem was in missing NULL check. hu->serdev can be NULL and we should not blindly pass &serdev->dev somewhere, since it will cause GPF. Reported-by:
<syzbot+b9bd12fbed3485a3e51f@syzkaller.appspotmail.com> Fixes: d9dd833c ("Bluetooth: hci_h5: Add runtime suspend") Signed-off-by:
Pavel Skripkin <paskripkin@gmail.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
This fixes the following trace caused by receiving HCI_EV_DISCONN_PHY_LINK_COMPLETE which does call hci_conn_del without first checking if conn->type is in fact AMP_LINK and in case it is do properly cleanup upper layers with hci_disconn_cfm: ================================================================== BUG: KASAN: use-after-free in hci_send_acl+0xaba/0xc50 Read of size 8 at addr ffff88800e404818 by task bluetoothd/142 CPU: 0 PID: 142 Comm: bluetoothd Not tainted 5.17.0-rc5-00006-gda4022eeac1a #7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x45/0x59 print_address_description.constprop.0+0x1f/0x150 kasan_report.cold+0x7f/0x11b hci_send_acl+0xaba/0xc50 l2cap_do_send+0x23f/0x3d0 l2cap_chan_send+0xc06/0x2cc0 l2cap_sock_sendmsg+0x201/0x2b0 sock_sendmsg+0xdc/0x110 sock_write_iter+0x20f/0x370 do_iter_readv_writev+0x343/0x690 do_iter_write+0x132/0x640 vfs_writev+0x198/0x570 do_writev+0x202/0x280 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RSP: 002b:00007ffce8a099b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000014 Code: 0f 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 14 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10 RDX: 0000000000000001 RSI: 00007ffce8a099e0 RDI: 0000000000000015 RAX: ffffffffffffffda RBX: 00007ffce8a099e0 RCX: 00007f788fc3cf77 R10: 00007ffce8af7080 R11: 0000000000000246 R12: 000055e4ccf75580 RBP: 0000000000000015 R08: 0000000000000002 R09: 0000000000000001 </TASK> R13: 000055e4ccf754a0 R14: 000055e4ccf75cd0 R15: 000055e4ccf4a6b0 Allocated by task 45: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x81/0xa0 hci_chan_create+0x9a/0x2f0 l2cap_conn_add.part.0+0x1a/0xdc0 l2cap_connect_cfm+0x236/0x1000 le_conn_complete_evt+0x15a7/0x1db0 hci_le_conn_complete_evt+0x226/0x2c0 hci_le_meta_evt+0x247/0x450 hci_event_packet+0x61b/0xe90 hci_rx_work+0x4d5/0xc50 process_one_work+0x8fb/0x15a0 worker_thread+0x576/0x1240 kthread+0x29d/0x340 ret_from_fork+0x1f/0x30 Freed by task 45: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 kasan_set_free_info+0x20/0x30 __kasan_slab_free+0xfb/0x130 kfree+0xac/0x350 hci_conn_cleanup+0x101/0x6a0 hci_conn_del+0x27e/0x6c0 hci_disconn_phylink_complete_evt+0xe0/0x120 hci_event_packet+0x812/0xe90 hci_rx_work+0x4d5/0xc50 process_one_work+0x8fb/0x15a0 worker_thread+0x576/0x1240 kthread+0x29d/0x340 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff88800c0f0500 The buggy address is located 24 bytes inside of which belongs to the cache kmalloc-128 of size 128 The buggy address belongs to the page: 128-byte region [ffff88800c0f0500, ffff88800c0f0580) flags: 0x100000000000200(slab|node=0|zone=1) page:00000000fe45cd86 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xc0f0 raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000 raw: 0100000000000200 ffffea00003a2c80 dead000000000004 ffff8880078418c0 page dumped because: kasan: bad access detected ffff88800c0f0400: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc Memory state around the buggy address: >ffff88800c0f0500: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800c0f0480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800c0f0580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ================================================================== ffff88800c0f0600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Reported-by:Sönke Huster <soenke.huster@eknoes.de> Tested-by:
-
Ismael Ferreras Morezuelas authored
Another subset of the more recent batch of Chinese clones aren't specs-compliant and seem to lock up whenever they receive a HCI_OP_SET_EVENT_FLT with flt_type set to zero/HCI_FLT_CLEAR_ALL, which on Linux (until the recent HCI state-machine refactor) happened right at BR/EDR setup. As there are other less-straightforward ways of reaching those operations, this patch is still relevant. So, while all the previous efforts to wrangle the herd of fake CSRs seem to be paying off (and these also get detected as such) we still need to take care of this quirk; testers seem to agree that these dongles tend to work well enough afterwards. From some cursory USB packet capture on Windows it seems like that driver doesn't appear to use this clear-all functionality at all. This patch was tested on some really popular AliExpress-style dongles, in my case marked as "V5.0". Chip markings: UG8413, the backside of the PCB says "USB Dangel" (sic). Here is the `hciconfig -a` output; for completeness: hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:7X:XX ACL MTU: 679:8 SCO MTU: 48:16 UP RUNNING PSCAN ISCAN Features: 0xbf 0x3e 0x4d 0xfa 0xdb 0x3d 0x7b 0xc7 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: PERIPHERAL ACCEPT Name: 'CSR8510 A10.' Class: 0x7c0104 Service Classes: Rendering, Capturing, Object Transfer, Audio, Telephony Device Class: Computer, Desktop workstation HCI Version: 4.0 (0x6) Revision: 0x3120 LMP Version: 4.0 (0x6) Subversion: 0x22bb Manufacturer: Cambridge Silicon Radio (10) As well as the `lsusb -vv -d 0a12:0001`: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 224 Wireless bDeviceSubClass 1 Radio Frequency bDeviceProtocol 1 Bluetooth bMaxPacketSize0 64 idVendor 0x0a12 Cambridge Silicon Radio, Ltd idProduct 0x0001 Bluetooth Dongle (HCI mode) bcdDevice 88.91 iManufacturer 0 iProduct 2 BT DONGLE10 iSerial 0 bNumConfigurations 1 Also, changed the benign dmesg print that shows up whenever the generic force-suspend fails from bt_dev_err to bt_dev_warn; it's okay and done on a best-effort basis, not a problem if that does not work. Also, swapped the HCI subver and LMP subver numbers for the Barrot in the comment, which I copied wrong the last time around. Fixes: 81cac64b ("Bluetooth: Deal with USB devices that are faking CSR vendor") Fixes: cde1a8a9 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers") Fixes: d74e0ae7 ("Bluetooth: btusb: Fix detection of some fake CSR controllers with a bcdDevice val of 0x0134") Fixes: 0671c066 ("Bluetooth: btusb: Add workaround for remote-wakeup issues with Barrot 8041a02 fake CSR controllers") Fixes: f4292e2f ("Bluetooth: btusb: Make the CSR clone chip force-suspend workaround more generic") Link: https://bugzilla.kernel.org/show_bug.cgi?id=60824 Link: https://gist.github.com/nevack/6b36b82d715dc025163d9e9124840a07 Cc: stable@vger.kernel.org Cc: Hans de Goede <hdegoede@redhat.com> Tested-by:
Gonzalo Tornaría <tornaria@cmat.edu.uy> Tested-by:
Mateus Lemos <lemonsmateus@gmail.com> Tested-by:
Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Ismael Ferreras Morezuelas authored
Some controllers have problems with being sent a command to clear all filtering. While the HCI code does not unconditionally send a clear-all anymore at BR/EDR setup (after the state machine refactor), there might be more ways of hitting these codepaths in the future as the kernel develops. Cc: stable@vger.kernel.org Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Sean Wang authored
There is a conflict between MediaTek wmt event and msft vendor extension logic in the core layer since 145373cb ("Bluetooth: Add framework for Microsoft vendor extension") was introduced because we changed the type of mediatek wmt event to the type of msft vendor event in the driver. But the purpose we reported mediatek event to the core layer is for the diagnostic purpose with that we are able to see the full packet trace via monitoring socket with btmon. Thus, it is harmless we keep the original type of mediatek vendor event here to avoid breaking the msft extension function especially they can be supported by Mediatek future devices. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Sean Wang authored
add .set_bdaddr support Signed-off-by:
-
Sean Wang authored
Rely on btmtk module to reduce duplicated code Signed-off-by:
-
Takashi Iwai authored
Chicony Electronics BT device with 04f2:b49f seems to be a missing entry for Realtek RTL8723BE. T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04f2 ProdID=b49f Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1196779 Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Colin Ian King authored
Variable cur_len is being ininitialized with a value in the start of a for-loop but this is never read, it is being re-assigned a new value on the first statement in the for-loop. The initialization is redundant and can be removed. Cleans up clang scan build warning: net/bluetooth/mgmt.c:7958:14: warning: Although the value stored to 'cur_len' is used in the enclosing expression, the value is never actually read from 'cur_len' [deadcode.DeadStores] Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
-
- Mar 18, 2022
-
-
Krasnov Arseniy Vladimirovich authored
Add test where sender sends two message, each with own data pattern. Reader tries to read first to broken buffer: it has three pages size, but middle page is unmapped. Then, reader tries to read second message to valid buffer. Test checks, that uncopied part of first message was dropped and thus not copied as part of second message. Signed-off-by:
Krasnov Arseniy Vladimirovich <AVKrasnov@sberdevices.ru> Reviewed-by:
Stefano Garzarella <sgarzare@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Krasnov Arseniy Vladimirovich authored
Test for receive timeout check: connection is established, receiver sets timeout, but sender does nothing. Receiver's 'read()' call must return EAGAIN. Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-next-2022-03-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v5.18 Third set of patches for v5.18. Smaller set this time, support for mt7921u and some work on MBSSID support. Also a workaround for rfkill userspace event. Major changes: mac80211 * MBSSID beacon handling in AP mode rfkill * make new event layout opt-in to workaround buggy user space rtlwifi * support On Networks N150 device id mt76 * mt7915: MBSSID and 6 GHz band support * new driver mt7921u ==================== Signed-off-by:
-
David S. Miller authored
Raju Lakkaraju says: ==================== net: lan743x: PCI11010 / PCI11414 devices This patch series continues with the addition of supported features for the Ethernet function of the PCI11010 / PCI11414 devices to the LAN743x driver. ==================== Signed-off-by: -
Raju Lakkaraju authored
Add support for PTP-IO Event Output (Periodic Output - perout) for PCI11010/PCI11414 chips Signed-off-by:
Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Signed-off-by:
-
Raju Lakkaraju authored
PTP-IOs block provides for time stamping PTP-IO input events. PTP-IOs are numbered from 0 to 11. When a PTP-IO is enabled by the corresponding bit in the PTP-IO Capture Configuration Register, a rising or falling edge, respectively, will capture the 1588 Local Time Counter Signed-off-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
Raju Lakkaraju authored
Add new the OTP read and write access functions for PCI11010/PCI11414 chips PCI11010/PCI11414 OTP module register offsets are different from LAN743x OTP module Signed-off-by:
-
Raju Lakkaraju authored
Add new the EEPROM read and write access functions and system lock protection to access by devices for PCI11010/PCI11414 chips Signed-off-by:
-
Raju Lakkaraju authored
Tx 4 queue statistics display through ethtool application Signed-off-by:
-
Johannes Berg authored
Again new complaints surfaced that we had broken the ABI here, although previously all the userspace tools had agreed that it was their mistake and fixed it. Yet now there are cases (e.g. RHEL) that want to run old userspace with newer kernels, and thus are broken. Since this is a bit of a whack-a-mole thing, change the whole extensibility scheme of rfkill to no longer just rely on the message lengths, but instead require userspace to opt in via a new ioctl to a given maximum event size that it is willing to understand. By default, set that to RFKILL_EVENT_SIZE_V1 (8), so that the behaviour for userspace not calling the ioctl will look as if it's just running on an older kernel. Fixes: 14486c82 ("rfkill: add a reason to the HW rfkill state") Cc: stable@vger.kernel.org # 5.11+ Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220316212749.16491491b270.Ifcb1950998330a596f29a2a162e00b7546a1d6d0@changeid
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2022-03-17 1) From Maxim Mikityanskiy, Datapath improvements in preparation for XDP multi buffer This series contains general improvements for the datapath that are useful for the upcoming XDP multi buffer support: a. Non-linear legacy RQ: validate MTU for robustness, build the linear part of SKB over the first hardware fragment (instead of copying the packet headers), adjust headroom calculations to allow enabling headroom in the non-linear mode (useful for XDP multi buffer). b. XDP: do the XDP program test before function call, optimize parameters of mlx5e_xdp_handle. 2) From Rongwei Liu, DR, reduce steering memory usage Currently, mlx5 driver uses mlx5_htbl/chunk/ste to organize steering logic. However there is a little memory waste. This update targets to reduce steering memory footprint by: a. Adjust struct member layout. b. Remove duplicated indicator by using simple functions call. With 500k TX rules(3 ste) plus 500k RX rules(6 stes), these patches can save around 17% memory. 3) Three cleanup commits at the end of this series. =================== Signed-off-by: -
Jakub Kicinski authored
Vladimir Oltean says: ==================== Mirroring for Ocelot switches This series adds support for tc-matchall (port-based) and tc-flower (flow-based) offloading of the tc-mirred action. Support has been added for both the ocelot switchdev driver and felix DSA driver. ==================== Link: https://lore.kernel.org/r/20220316204144.2679277-1-vladimir.oltean@nxp.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Vladimir Oltean authored
Gain support for port mirroring using tc-matchall by forwarding the calls to the ocelot switch library. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
Drivers might have error messages to propagate to user space, most common being that they support a single mirror port. Propagate the netlink extack so that they can inform user space in a verbal way of their limitations. Signed-off-by:
-
Vladimir Oltean authored
Per-flow mirroring with the VCAP IS2 TCAM (in itself handled as an offload for tc-flower) is done by setting the MIRROR_ENA bit from the action vector of the filter. The packet is mirrored to the port mask configured in the ANA:ANA:MIRRORPORTS register (the same port mask as the destinations for port-based mirroring). Functionality was tested with: tc qdisc add dev swp3 clsact tc filter add dev swp3 ingress protocol ip \ flower skip_sw ip_proto icmp \ action mirred egress mirror dev swp1 and pinging through swp3, while seeing that the ICMP replies are mirrored towards swp1. Signed-off-by:
-
Vladimir Oltean authored
Some VCAP filters utilize resources which are global to the switch, like for example VCAP IS2 policers take an index into a global policer pool. In commit c9a7fe12 ("net: mscc: ocelot: add action of police on vcap_is2"), Xiaoliang expressed this by hooking into the low-level ocelot_vcap_filter_add_to_block() and ocelot_vcap_block_remove_filter() functions, and allocating/freeing the policers from there. Evaluating the code, there probably isn't a better place, but we'll need to do something similar for the mirror ports, and the code will start to look even more hacked up than it is right now. Create two ocelot_vcap_filter_{add,del}_aux_resources() functions to contain the madness, and pollute less the body of other functions such as ocelot_vcap_filter_add_to_block(). Signed-off-by:
-
Vladimir Oltean authored
Ocelot switches perform port-based ingress mirroring if ANA:PORT:PORT_CFG field SRC_MIRROR_ENA is set, and egress mirroring if the port is in ANA:ANA:EMIRRORPORTS. Both ingress-mirrored and egress-mirrored frames are copied to the port mask from ANA:ANA:MIRRORPORTS. So the choice of limiting to a single mirror port via ocelot_mirror_get() and ocelot_mirror_put() may seem bizarre, but the hardware model doesn't map very well to the user space model. If the user wants to mirror the ingress of swp1 towards swp2 and the ingress of swp3 towards swp4, we'd have to program ANA:ANA:MIRRORPORTS with BIT(2) | BIT(4), and that would make swp1 be mirrored towards swp4 too, and swp3 towards swp2. But there are no tc-matchall rules to describe those actions. Now, we could offload a matchall rule with multiple mirred actions, one per desired mirror port, and force the user to stick to the multi-action rule format for subsequent matchall filters. But both DSA and ocelot have the flow_offload_has_one_action() check for the matchall offload, plus the fact that it will get cumbersome to cross-check matchall mirrors with flower mirrors (which will be added in the next patch). As a result, we limit the configuration to a single mirror port, with the possibility of lifting the restriction in the future. Frames injected from the CPU don't get egress-mirrored, since they are sent with the BYPASS bit in the injection frame header, and this bypasses the analyzer module (effectively also the mirroring logic). I don't know what to do/say about this. Functionality was tested with: tc qdisc add dev swp3 clsact tc filter add dev swp3 ingress \ matchall skip_sw \ action mirred egress mirror dev swp1 and pinging through swp3, while seeing that the ICMP replies are mirrored towards swp1. Signed-off-by:
-
Vladimir Oltean authored
In preparation for adding port mirroring support to the ocelot driver, the dispatching function ocelot_setup_tc_cls_matchall() must be free of action-specific code. Move port policer creation and deletion to separate functions. Signed-off-by:
-
Jonathan Lemon authored
An earlier patch mistakenly changed these variables from u32 to u16, leading to unintended truncation. Restore the original logic. Fixes: a509a7c6 ("ptp: ocp: Add support for selectable SMA directions.") Reported-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Link: https://lore.kernel.org/r/20220316165347.599154-1-jonathan.lemon@gmail.com Signed-off-by:
-
Oleksij Rempel authored
According to erratum described in DS80000687C[1]: "Module 2: Link drops with some EEE link partners.", we need to "Disable the EEE next page exchange in EEE Global Register 2" 1 - https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ87xx-Errata-DS80000687C.pdf Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20220316125529.1489045-1-o.rempel@pengutronix.de Signed-off-by:
-
Jakub Kicinski authored
Tobias Waldekranz says: ==================== net: bridge: Multiple Spanning Trees The bridge has had per-VLAN STP support for a while now, since: https://lore.kernel.org/netdev/20200124114022.10883-1-nikolay@cumulusnetworks.com/ The current implementation has some problems: - The mapping from VLAN to STP state is fixed as 1:1, i.e. each VLAN is managed independently. This is awkward from an MSTP (802.1Q-2018, Clause 13.5) point of view, where the model is that multiple VLANs are grouped into MST instances. Because of the way that the standard is written, presumably, this is also reflected in hardware implementations. It is not uncommon for a switch to support the full 4k range of VIDs, but that the pool of MST instances is much smaller. Some examples: Marvell LinkStreet (mv88e6xxx): 4k VLANs, but only 64 MSTIs Marvell Prestera: 4k VLANs, but only 128 MSTIs Microchip SparX-5i: 4k VLANs, but only 128 MSTIs - By default, the feature is enabled, and there is no way to disable it. This makes it hard to add offloading in a backwards compatible way, since any underlying switchdevs have no way to refuse the function if the hardware does not support it - The port-global STP state has precedence over per-VLAN states. In MSTP, as far as I understand it, all VLANs will use the common spanning tree (CST) by default - through traffic engineering you can then optimize your network to group subsets of VLANs to use different trees (MSTI). To my understanding, the way this is typically managed in silicon is roughly: Incoming packet: .----.----.--------------.----.------------- | DA | SA | 802.1Q VID=X | ET | Payload ... '----'----'--------------'----'------------- | '->|\ .----------------------------. | +--> | VID | Members | ... | MSTI | PVID -->|/ |-----|---------|-----|------| | 1 | 0001001 | ... | 0 | | 2 | 0001010 | ... | 10 | | 3 | 0001100 | ... | 10 | '----------------------------' | .-----------------------------' | .------------------------. '->| MSTI | Fwding | Lrning | |------|--------|--------| | 0 | 111110 | 111110 | | 10 | 110111 | 110111 | '------------------------' What this is trying to show is that the STP state (whether MSTP is used, or ye olde STP) is always accessed via the VLAN table. If STP is running, all MSTI pointers in that table will reference the same index in the STP stable - if MSTP is running, some VLANs may point to other trees (like in this example). The fact that in the Linux bridge, the global state (think: index 0 in most hardware implementations) is supposed to override the per-VLAN state, is very awkward to offload. In effect, this means that when the global state changes to blocking, drivers will have to iterate over all MSTIs in use, and alter them all to match. This also means that you have to cache whether the hardware state is currently tracking the global state or the per-VLAN state. In the first case, you also have to cache the per-VLAN state so that you can restore it if the global state transitions back to forwarding. This series adds a new mst_enable bridge setting (as suggested by Nik) that can only be changed when no VLANs are configured on the bridge. Enabling this mode has the following effect: - The port-global STP state is used to represent the CST (Common Spanning Tree) (1/15) - Ingress STP filtering is deferred until the frame's VLAN has been resolved (1/15) - The preexisting per-VLAN states can no longer be controlled directly (1/15). They are instead placed under the MST module's control, which is managed using a new netlink interface (described in 3/15) - VLANs can br mapped to MSTIs in an arbitrary M:N fashion, using a new global VLAN option (2/15) Switchdev notifications are added so that a driver can track: - MST enabled state - VID to MSTI mappings - MST port states An offloading implementation is this provided for mv88e6xxx. ==================== Link: https://lore.kernel.org/r/20220316150857.2442916-1-tobias@waldekranz.com Signed-off-by:
-
Tobias Waldekranz authored
Allocate a SID in the STU for each MSTID in use by a bridge and handle the mapping of MSTIDs to VLANs using the SID field of each VTU entry. Signed-off-by:
Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by:
-
Tobias Waldekranz authored
Export the raw STU data in a devlink region so that it can be inspected from userspace and compared to the current bridge configuration. Signed-off-by:
-
Tobias Waldekranz authored
In early LinkStreet silicon (e.g. 6095/6185), the per-VLAN STP states were kept in the VTU - there was no concept of a SID. Later, the information was split into two tables, where the VTU only tracked memberships and deferred the STP state tracking to the STU via a pointer (SID). This meant that a group of VLANs could share the same STU entry. Most likely, this was done to align with MSTP (802.1Q-2018, Clause 13), which is built on this principle. While the VTU is still 4k lines on most devices, the STU is capped at 64 entries. This means that the current stategy, updating STU info whenever a VTU entry is updated, can not easily support MSTP because: - The maximum number of VIDs would also be capped at 64, as we would have to allocate one SID for every VTU entry - even if many VLANs would effectively share the same MST. - MSTP updates would be unnecessarily slow as you would have to iterate over all VLANs that share the same MST. In order to support MSTP offloading in the future, manage the STU as a separate entity from the VTU. Only add support for newer hardware with separate VTU and STU. VTU-only devices can also be supported, but essentially this requires a software implementation of an STU (fanning out state changed to all VLANs tied to the same MST). Signed-off-by:
-
