- Oct 28, 2014
-
-
Felix Fietkau authored
On some devices (especially little-endian ones), the flash EEPROM data has a different endian, which needs to be detected. Add a flag to the platform data to allow overriding that behavior Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
This makes the initial NF calibration less likely to fail. Signed-off-by:
-
Felix Fietkau authored
It can cause inconsistent calibration results or in some cases turn the radio deaf. Signed-off-by:
-
Felix Fietkau authored
When NF calibration fails, the radio often becomes deaf. The usual hardware hang checks do not detect this, so it's better to issue a reset when that happens. Signed-off-by:
-
Felix Fietkau authored
Reduce code duplication Signed-off-by:
-
Felix Fietkau authored
The "goto chip_reset" is a bit misleading, because it does not actually issue a chip reset. Instead it is bypassing processing of other interrupts and assumes that the tasklet will issue a chip reset. In the case of RXORN this does not happen, so bypassing processing of other interrupts will simply allow them to fire again. Even if RXORN was triggering a reset, it is not critical enough to need the bypass here. Signed-off-by:
-
Felix Fietkau authored
UB124 is a USB based reference design not supported by ath9k or ath9k_htc. Signed-off-by:
-
Felix Fietkau authored
The initvals use up quite a bit of space, and PC-OEM support is typically not needed on embedded systems Signed-off-by:
-
Sujith Manoharan authored
* Fix a 11b/EVM issue by adjusting FIR filter coefficients. * Fix a problem with receiving probe request frames sent at 11b rate. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
This fixes RX sensitivity issues with AR9580. Signed-off-by:
-
Sujith Manoharan authored
mac80211 currently has a race which can be hit with this sequence: * Start a scan operation. * TX BA is initiated by ieee80211_start_tx_ba_session(). * Driver sets up internal state and calls ieee80211_start_tx_ba_cb_irqsafe(). * mac80211 adds a packet to sdata->skb_queue with type IEEE80211_SDATA_QUEUE_AGG_START. * ieee80211_iface_work() doesn't process the packet because scan is in progress. * ADDBA response timer expires and the sta/tid is torn down. * Driver receives BA stop notification and calls ieee80211_stop_tx_ba_cb_irqsafe(). * This is also added to the queue by mac80211. * Now, scan finishes. At this point, the queued up packets might be processed if some other operation schedules the sdata work. Since the tids have been cleaned up already, warnings are hit. If this doesn't happen, the packets are left in the queue until the interface is torn down. Since initiating a BA session when scan is in progress leads to flaky connections, especially in MCC mode, we can drop the TX BA request. This improves connectivity with legacy clients in MCC mode. Signed-off-by:
-
Sujith Manoharan authored
The flush timeout in MCC mode is very small, since we are constrained by the time slice for each channel context, but since only the HW queues are flushed when switching contexts, it is acceptable. Since the SW queues are also emptied in the mac80211 flush() callback, a larger duration is needed. Add an override argument to __ath9k_flush() and set it when flush() is called in MCC mode. This allows the driver to drain both the SW and HW queues. Signed-off-by:
-
Sujith Manoharan authored
Instead of using ATH_CHANCTX_EVENT_ASSIGN to abort a HW scan when a new interface becomes active, use the mgd_prepare_tx() callback. This allows us to make sure that the GO's channel becomes operational by using flush_work(). Signed-off-by:
-
Sujith Manoharan authored
This patch makes sure that a GO interface sends out a new NoA schedule with 200ms duration when mgd_prepare_tx() is called. Signed-off-by:
-
Sujith Manoharan authored
mac80211 has to be notified when a RoC period expires in the driver. In MCC mode, since the offchannel/RoC timer is set with the requested duration, ieee80211_remain_on_channel_expired() needs to be called when the timer expires. But, currently it is done after we move back to the operating channel. This is incorrect - fix this by calling ieee80211_remain_on_channel_expired() when the RoC timer expires and in ath_roc_complete() when the RoC request is aborted. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
If a GO interface is active when we receive a mgd_prepare_tx() call, then we need to send out a new NoA before switching to a new context. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Since both the arguments need to satisfy the alignment requirements of ether_addr_copy(), use memcpy() in cases where there will be no big performance benefit and make sure that ether_addr_copy() calls use properly aligned arguments. Signed-off-by:
-
Sujith Manoharan authored
ATH_CHANCTX_EVENT_AUTHORIZED is required to trigger the MCC scheduler when a station interface becomes authorized. But, since the driver gets station state notifications when the current operating mode is AP too, make sure that we send ATH_CHANCTX_EVENT_AUTHORIZED only when the interface is in station mode. Signed-off-by:
-
Sujith Manoharan authored
Pending frames in the driver can be present either in the HW queues or SW. ath9k_has_pending_frames() currently checks for the HW queues first and then checks if any ACs are queued in the driver. In MCC mode, we need to check the HW queues alone, since the SW queues are just marked as 'stopped' - they will be processed in the next context switch. But since we don't differentiate this now, mention whether we want to check if there are frames in the SW queues. * The flush() callback checks both HW and SW queues. * The tx_frames_pending() callback does the same. * The call to __ath9k_flush() in MCC mode checks HW queues alone. Signed-off-by:
-
Sujith Manoharan authored
An offchannel operation also needs to have a flush timeout that doesn't exceed the NoA absence duration of a GO context, so use channel_switch_time. The first offchannel operation is set a flush timeout of 10ms since channel_switch_time will be zero. Signed-off-by:
-
Sujith Manoharan authored
In MCC mode, the duration for a channel context is half the beacon interval and having a large flush timeout will adversely affect GO operation, since the default value of 200ms will overshoot the advertised NoA absence duration. The scheduler initiates a channel context switch only when the slot duration for the current context expires, so there is no possibility of having a fixed timeout for flush. Since the channel_switch_time is added to the absence duration when the GO sets up the NoA attribute, this is the maximum time that we have to flush the TX queues. The duration is very small, but we don't have a choice in MCC mode. Signed-off-by:
-
Sujith Manoharan authored
The timeout value for flushing the TX queues is hardcoded at 200ms right now. Use a channel context-specific value instead to allow adjustments to the timeout in case MCC is enabled. Signed-off-by:
-
Sujith Manoharan authored
When an active context transitions to inactive state, the NoA schedule needs to be removed for the context that has beaconing enabled. Not doing this will affect p2p clients. Signed-off-by:
-
Sujith Manoharan authored
When a chip reset is done, all running timers, tasklets etc. are stopped but the beacon tasklet is left running. Fix this. Signed-off-by:
-
Sujith Manoharan authored
When a HW reset is done, the interrupt tasklet is disabled before ISRs are disabled in the HW. This allows a small window where the HW can still generate interrupts. Since the tasklet is disabled and not killed, it is not scheduled but deferred for execution at a later time. This happens because ATH_OP_HW_RESET is not set when ath_reset() is called. When the hw_reset_work workqueue is used, this problem doesn't arise because ATH_OP_HW_RESET is set and the ISR bails out. Set ATH_OP_HW_RESET properly in ath_reset() to avoid this race - all the ath_reset_internal() callers have been converted to use ath_reset() in the previous patch. Signed-off-by:
-
Sujith Manoharan authored
Instead of having ath_reset_internal() and ath_reset() as two separate calls to perform a HW reset, have one function. This makes sure that the behavior will be the same at all callsites. Signed-off-by:
-
Sujith Manoharan authored
When the current operating channel context has been marked as ATH_CHANCTX_STATE_FORCE_ACTIVE, do not process beacons that might be received, since we have to wait for the station to become authorized. Also, since the cached TSF value will be zero initially do not rearm the timer in this case when a beacon is received, since it results in spurious values. Signed-off-by:
-
Sujith Manoharan authored
In MCC mode, currently the decision to enable the multi-channel state machine is done based on the association status if one of the interfaces assigned to a context is in station mode. This allows the driver to switch to the other context before the current station is able to complete the 4-way handshake in case it is required and this causes problems. Instead, enable multi-channel mode when the station moves to the authorized state. This disallows an early switch to the other channel. Signed-off-by:
-
Sujith Manoharan authored
Instead of using the sta_add()/sta_remove() callbacks, use the sta_state() callback since this gives more fine-grained control. Signed-off-by:
-
Lorenzo Bianconi authored
Do not overwrite AR_PHY_RADAR_1 most significant byte default value Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by:
-
Dan Carpenter authored
The original condition was "(PAGE_SIZE - len)" when "(len < PAGE_SIZE)" is intended. This condition is not really sufficient, but also not really needed... If "len > PAGE_SIZE" then it we will print a warning message in dmesg but there are no other effects. Maybe we should just remove the condition? Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
The ->ibss_dfs pointer is always allocated with a user controlled length. This caused a static checker warning because what if the length was zero? In that case, any dereference of ->ibss_dfs would lead to an Oops. It turns out that this isn't a problem because the ->ibss_dfs pointer is never used. This patch deletes it along with all the related code. In particular the entire libipw_network_reset() function can be removed. Signed-off-by:
-
Stanislaw Gruszka authored
We provide timeout value to rt2x00usb_vendor_request_buff() based on number of registers to process. That value is passed down to rt2x00usb_vendor_req_buff_lock() and ends in usb_control_msg(). But we do not read/write all registers in rt2x00usb_vendor_req_buff_lock() at once. We read/write them in chunks of 64 bytes in the loop, hence passed timeout value to low level is too big. Patch removes timeout argument from rt2x00usb_vendor_request_buff() and use short REGISTER_TIMEOUT in rt2x00usb_vendor_req_buff_lock(). That timeout value should be fine for 64 bytes and smaller requests. For EEPROM read we introduced new timeout value equal to 2 seconds. Patch fixes process uninterruptible sleep stalls for long period, when USB bus has problem to satisfy a request and we wait very long time on usb_start_wait_urb(). Reported-and-tested-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Rafał Miłecki authored
We were setting things like dma_dev, IRQ, etc. during core registration only. We need such info for cores handled internally (e.g. ChipCommon) as well. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Acked-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
git://github.com/kvalo/athJohn W. Linville authored
Conflicts: drivers/net/wireless/ath/wil6210/wil6210.h
-
- Oct 23, 2014
-
-
Michal Kazior authored
Calling init to reinit ce pipe state would also re-set all static structure links and setting (which don't change over driver lifecycle). Make it so alloc links structures and initializes static data and init part to setup state variables and clear stuff. Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com>
-
