Without this the jitter on the touchscreen makes it hard to use for
most GUI toolkits.

Signed-off-by: James <Ketrenos&lt;jketreno@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The Bamboo Touch reports a sub-screen resolution of 480x320.  The
signal-to-noise ratio is only about 100, so filtering is needed in
order to reduce the jitter to a usable level. However, the low
resolution leads to round-off errors in the EWMA filter, resulting in
extremely jerky pointer motion. This patch explicitly sets a higher
resolution for those devices, and tells this to the completion handler
via a low-resolution quirk.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Add support for the Bamboo Touch trackpad, and make it work with
both the Synaptics X Driver and the Multitouch X Driver. The device
uses MT slots internally, so the choice of protocol is a given.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Collect device-specific code into a single function, and use quirks to
flag specific behavior instead.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The Bamboo devices have multiple interfaces which need to be setup
separately. Use the HID parsing mechanism to achieve that.

Signed-off-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The signal-to-noise ratio varies between devices, but currently all
devices are treated the same way. Add fuzz parameters to the feature
struct, allowing for tailored treatment of devices.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Conflicts:
	drivers/input/touchscreen/Makefile

Add the PowerOn (PonKey) button support to detect power on/off events.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Add logic to wm97xx_read_aux_adc() to retry reading the adc if the
sample failed.  This could occur if the previous sample was still in
the return register or the sample timed-out.  Also avoid a pathologic
failure mode by disabling the digitizer and returning -EBUSY after 5
retries.

Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Use platform_device_del() instead of platform_device_unregister() in error
handling path.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

It is forbidden to call input_free_device() after input_unregister_device().

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Once device is registered we should call input_unregister_device()
instead of input_free_device().

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

We call platform_get_drvdata() in tps6507x_ts_remove(),
thus we should call platform_set_drvdata() in tps6507x_ts_probe().

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Use input_free_device() to free devices that have not been registered.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Add support for Art Master III tablet of BeiJing HanwangTechnology Co, Ltd.

Signed-off-by: Xing Wei <weixing@hanwang.com.cn>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The driver is in reasonable shape now so let's move it out of staging.

Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Use 8 bit update commands instead of a 16 bit unaligned read/write
pair which fails after the first few calls; the voodoo in the original
doesn't seem to be required with this mechanism.

Tested-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The touch screen driver tries to find a range of free channels (which
are an array of bytes), by scanning for the "end of used channel" marker.
However it tries to be WAAAAY too smart and does 32 bit logic on 8 bit
quantities, and in the process completely gets it wrong
(repeatedly read the same register instead of incrementing in the loop,
assuming that if any of the 4 bytes in the 32 byte quantity is free,
all four are free, returning the channel number divided by 4 rather than
the actual first free channel number)

On the setting side, the same mistakes are made by and large; changed
this to just use the byte SCU write functions....

With these fixes we go from a completely non detected touchscreen to
something that appears to completely get detected.
(after also fixing the ordering issue that Jacobs patch should solve)

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

AC: Reworked to merge with upstream input device work from Dmitry et al.

Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Changes:

 - switch to use threaded IRQ
 - more __devinit/__devexit annotations
 - rely on input core to remove jitter from events
 - global pointer removed
 - NEC/MAXIM/Freescale handling factored out

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Fix most of the stuff that Dmitry pointed out. This leaves the mutex in IRQ
and misuse of SPI to sort out.

Also fix the build bits so it actually builds in staging - whoops.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

OMAP4 keyboard controller includes:
  - built-in scanning algorithm
  - debouncing feature

Driver implementation is based on matrix_keypad.c

Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch set introduces support for the LPC32xx touchscreen
controller driver. The LPC32xx touchscreen controller supports
automated event detection and X/Y data conversion for resistive
touchscreens.

Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Durgesh Pattamatta <durgesh.pattamatta@nxp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Some serial wacom devices support two-finger touch. Test for this during
init and parse the touch packets accordingly. Touch packets are
processed using Protocol B (MT Slots).

Note: there are several wacom versions that do touch but not two-finger
touch. These are not catered for here, touch events for these are simply
discarded.

Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Tablets that support touch input may report different sized packages,
depending on the touch sensor in the tablet. For now, discard the
packages until we report them as touch input proper.

Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The protocol used by the w8001 supports status fields for tip, side
switch and eraser as well as a RDY field for proximity.

The protocol has a double usage for the f2 bit in the packet. If set,
the data is either pen + side2 button or eraser. Assume eraser if the
device comes into proximity with the f2 bit set, otherwise trigger the
side2 button. If the device comes into proximity with the f2 bit and
that bit disappears afterwards, fake proximity out for the eraser and
proximity in for the pen.

Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

For MT slots, the ABS_MT_TRACKING_ID determines whether a slot is in use,
but currently leaves initialization up to the drivers. This patch sets the
slot state to unused upon creation.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The KIOCSOUND and KDMKTONE ioctls are based on the CLOCK_TICK_RATE,
which is architecture and sometimes configuration specific.

In practice, most user applications assume that it is actually defined
as the i8253 PIT base clock of 1193182 Hz, which is true on some
architectures but not on others.

This patch makes the vt code use the PIT frequency on all
architectures, which is much more well-defined.  It will change the
behavior of user applications sending the beep ioctl on all
architectures that define CLOCK_TICK_RATE different from
PIT_TICK_RATE.

The original breakage was introduced in commit bcc8ca09

 "Adapt
drivers/char/vt_ioctl.c to non-x86".  Hopefully, reverting this change
will make the frequency correct in more cases than it will make it
incorrect.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This fixes a regression introduced in
3b57ca0f

.

The data[6] byte contains either 1 or -1 depending on the whether the
mouse wheel on older wacom tablets is moved down (1) or up (-1).  The
patch introduced in the above commit changed the cast from (signed char)
to (signed).  When cast as a signed integer and negated, the value of -1
(stored in the byte as 0xff) became -255 rather than 1.  This patch
reverts the cast to a (signed char) and also removes an unnecessary
(signed) cast, as all the values operated on are bitmasked.

Signed-off-by: Mike Auty <ikelos@gentoo.org>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Cc; stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

No need to call input_free_device() after input_unregister_device().

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Introduced by 987a6c02

 a swap in max/min
calculation gets fixed by this patch.

Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Recent modprobe and udev versions allow to create device nodes
for modules which are not loaded. Only the first access will cause
the in-kernel module loader to pull-in the module. Systems which
never access the device node will not needlessly load the module,
and no longer need init scripts or other facilities to unconditionally
load it.

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Fix another compile breakage stemming from 987a6c02

 ("Input: switch to
input_abs_*() access functions")

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Since handle_sysrq() does not take tty as argument anymore we can
drop it from usb_serial_handle_sysrq_char() as well.

Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Sysrq operations do not accept tty argument anymore so no need to pass
it to us.

[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
 caused by sysrq using bool but not including linux/types.h]

[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
 driver]

Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Noone is using tty argument so let's get rid of it.

Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>