- May 24, 2009
-
-
git://git.pengutronix.de/git/imx/linux-2.6Russell King authored
Conflicts: arch/arm/Kconfig arch/arm/Makefile
-
- May 18, 2009
-
-
Magnus Lilja authored
The i.MX31 PDK consists of several boards, one of them is a debug board containing a CPLD which controls some debug leds, switch buttons, an interrupt chip and an Ethernet controller. This patch adds support for detecting if the PDK board is present (during boot) and adds the interrupt chip to the kernel. Signed-off-by:
Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
- May 17, 2009
-
-
Sascha Hauer authored
Without this patch we end up with a log message like "mx3_sdc_fb mx3_sdc_fb: mx3fb: fb registered". That's two fb too much for my taste. Signed-off-by:
-
- May 16, 2009
-
-
Magnus Lilja authored
Restructure UART pin setup in preparation for adding other pins in later patches. Signed-off-by:
-
Alberto Panizzo authored
From ff1fd9d7015d9b9ad3e0df2016d0415e2719747c Mon Sep 17 00:00:00 2001 From: Alberto Panizzo <maramaopercheseimorto@gmail.com> Date: Fri, 15 May 2009 17:21:21 +0200 Subject: [PATCH] Make sure ipg_per_clk is generated by ipg_clk and not usb_pll Signed-off-by:
Alberto Panizzo <maramaopercheseimorto@gmail.com> Signed-off-by:
-
Magnus Lilja authored
Signed-off-by:
-
- May 13, 2009
-
-
Guennadi Liakhovetski authored
mx3fb.c calls disable_irq() from a DMA callback, i.e., in an IRQ-handler context, which has always been unsafe, and became deadly after the merge of threaded interrupt handler support. Use disable_irq_nosync() instead. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
- May 07, 2009
-
-
Valentin Longchamp authored
Signed-off-by:
Valentin Longchamp <valentin.longchamp@epfl.ch> Acked-by:
-
Valentin Longchamp authored
This adds the camera device based on Guennadi's soc_camera architecture for the mx31. The proposed init by Guennadi was removed and must be implemented in the board init file as it contains a lot of board specific info (memory size, clock speed). Signed-off-by:
-
Valentin Longchamp authored
This is used on all board of our system, so again this is done in the mx31moboard.c file. changes since v2: call to gpio_request added in platform code, and moved device initialization in baseboard files. changes since v1: pins are claimed in another patch Signed-off-by:
-
Sascha Hauer authored
In order to use the gpiolib, we now have to call gpio_request in the plaform code since it is not done in iomux code anymore. Signed-off-by: -
Valentin Longchamp authored
Since iomux code is not directly related to gpio on mx31, the calls to gpio_request are removed from iomux.c file. These calls have to be done in platform initialization files. The name of the singe pin call for iomux is also changed to mxc_iomux_alloc_pin. Signed-off-by:
-
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
header is part of the kernel now. Signed-off-by: -
Guennadi Liakhovetski authored
Add OTG device definition and resources to i.MX31 and a pure USB device mode support to the pcm037 board. Signed-off-by:
Guennadi Liakhovetski <lg@denx.de> Signed-off-by:
-
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Also, remove usage of set_irq_type after request_irq. Signed-off-by: -
Vladimir Barinov authored
Add SDHC support for MX27ADS board Signed-off-by:
Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by:
-
Vladimir Barinov authored
Add 1-wire support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add Sharp-QVGA panel support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add I2C support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add NAND support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Setup all pins at once in one table Signed-off-by:
-
Magnus Lilja authored
This patch adds the SMSC platform device to the Litekit board. Signed-off-by:
-
Magnus Lilja authored
Several comments in board config files stated "mandatory for CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL. Signed-off-by:
-
Magnus Lilja authored
Signed-off-by:
-
Magnus Lilja authored
Signed-off-by:
-
Valentin Longchamp authored
This support both sdhc1 and sdhc2 with WP and CD for the marxbot and devboard mx31moboard baseboards. sdhc2 is present on both, but is not directly included in the mx31moboard file because a third baseboard (not supported yet) without sdhc2 is planned. Changes since v1: removed pin initialization from init/exit function and taken different comments into account Changes since v2: pin initialiation now is done in another patch for all current mx31moboard pins Signed-off-by:
-
Valentin Longchamp authored
Changes since v1: all the pins needed for the drivers are claimed in another patch Signed-off-by:
-
Valentin Longchamp authored
As suggested by Sascha, here we setup all the pins that we are using in the current (and currently reviewed) drivers for mx31moboard system. changes since v1: changed I2C1 pin names Signed-off-by:
-
Valentin Longchamp authored
As suggested by Sascha, I regroup them in a single patch so that the other patches become more orthogonal. changes since v1: changed I2C1 pin names Signed-off-by:
-
Alan Carvalho de Assis authored
This hw-random driver add support to RNGA hardware found on some i.MX processors. Signed-off-by:
Alan Carvalho de Assis <acassis@gmail.com> Acked-by:
Matt Mackall <mpm@selenic.com> Signed-off-by:
-
Valentin Longchamp authored
Various improvements (includes in alphabetical order, platform devices declaration order change, ...) The pins now are claimed in a single function call from a main table for every board for a better clarity and to adopt the current agreement for mx31 devices. Signed-off-by:
-
Fabio Estevam authored
This patch adds basic support to MX27PDK board http://www.freescale.com/imx27pdk ). Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Ivo Clarysse authored
Adds a defconfig file for the i.MX21 SoC, targeting the Freescale i.MX21ADS (M9328MX21ADSE) Application Development System. Signed-off-by:
Ivo Clarysse <ivo.clarysse@gmail.com> Signed-off-by:
-
Holger Schurig authored
* Kconfig enables now HAVE_PWM (this enables in turn the selection of CONFIG_BACKLIGHT_PWM) * changes CONFIG_ARCH_MXyy to CONFIG_MACH_MXyy * fix some register names to match those of the reference manual * write a stub code so that the PWM can be used to program the LCD backlight * convert from #ifdef CONFIG_ARCH_MXxx to cpu_is_mxXX() * remove unneeded defines and fix 80-column "violations" of checkpatch.pl Signed-off-by:
Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by:
-
