- Sep 23, 2022
-
-
FUKAUMI Naoki authored
fix regulator name. also, add vcc_3v3 and vdd_log. ref: https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi4c_plus_v12_sch_220304.pdf Signed-off-by:
FUKAUMI Naoki <naoki@radxa.com> Link: https://lore.kernel.org/r/20220909195006.127957-2-naoki@radxa.com Signed-off-by:
Heiko Stuebner <heiko@sntech.de>
-
FUKAUMI Naoki authored
GPIO pins for LEDs on ROCK 4C+ are in APIO5 Signed-off-by:
-
Chris Morgan authored
This adds the DSI controller nodes and DSI-DPHY controller nodes to the rk356x device tree. Signed-off-by:
Chris Morgan <macromorgan@hotmail.com> Acked-by:
Michael Riesch <michael.riesch@wolfvision.net> Link: https://lore.kernel.org/r/20220919164616.12492-4-macroalpha82@gmail.com Signed-off-by:
-
Nicolas Frattaroli authored
This enables the GPU and HDMI output (including HDMI audio) on the PINE64 Quartz64 Model B single board computer. Signed-off-by:
Nicolas Frattaroli <frattaroli.nicolas@gmail.com> Link: https://lore.kernel.org/r/20220920143446.633956-1-frattaroli.nicolas@gmail.com Signed-off-by:
-
- Sep 16, 2022
-
-
Tianling Shen authored
The only diffrence against the standrard edition is that the enterprise one has a built-in EEPROM chip which stores a globally unique MAC address. Signed-off-by:
Tianling Shen <cnsztl@gmail.com> Link: https://lore.kernel.org/r/20220915022511.4267-2-cnsztl@gmail.com Signed-off-by:
-
Tianling Shen authored
Add devicetree binding documentation for the FriendlyARM NanoPi R4S Enterprise Edition. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220915022511.4267-1-cnsztl@gmail.com Signed-off-by:
-
Quentin Schulz authored
The Rockchip PX30 SoC has three I2S controllers, i2s1 and i2s2 are 2-channel I2S/PCM controllers handled by the same controller driver, and i2s0 a 8-channel I2S/PCM/TDM controller handled by another controller driver. This adds the device tree node required to enable I2S0 on PX30. This was tested in a 2-channel I2S with TX BCLK/LRCK for both TX and RX (rockchip,trcm-sync-tx-only) setup on a soon-to-be-released board. Signed-off-by:
Quentin Schulz <quentin.schulz@theobroma-systems.com> Link: https://lore.kernel.org/r/20220916091746.35108-1-foss+kernel@0leil.net Signed-off-by:
-
- Sep 15, 2022
-
-
Markus Reichl authored
Add avdd-0v9-supply and avdd-1v8-supply to hdmi node for rk3399-roc-pc to silence dmesg warning and match the name of the 1v8 supply to the circuit sheet. Signed-off-by:
Markus Reichl <m.reichl@fivetechno.de> Link: https://lore.kernel.org/r/20220915111138.1108-1-m.reichl@fivetechno.de Signed-off-by:
-
Brian Norris authored
The Gru-Scarlet family includes a variety of SKU identifiers, using parts of a 3-bit space {0..7}. SKU2 and SKU4 devices (under a few different manufacturer names) also use the Innolux display. Without this, a SKU2 device may non-deterministically (depending on the matching order of DTBs and bootloader behavior) select either one of the INX DTBs (rk3399-gru-scarlet-dumo.dtb or rk3399-gru-scarlet-inx.dtb) or the KingDisplay DTB (rk3399-gru-scarlet-kd.dtb), to ill effect. For reference, the original vendor tree source: CHROMIUM: arm64: dts: rockchip: add sku{0,2,4} compatibility https://chromium.googlesource.com/chromiumos/third_party/kernel/+/f6ed665c9e2eb37fb2680debbb36ec9fb0e8fb97 CHROMIUM: arm64: dts: rockchip: scarlet: add SKU0 device tree https://chromium.googlesource.com/chromiumos/third_party/kernel/+/9987c8776f4b087d135d761e59f7fa6cc83fc7fc Signed-off-by:Brian Norris <briannorris@chromium.org> Link: https://lore.kernel.org/r/20220817123350.2.I5f4fd0808a927b08e267c189712fb4a85931fd3b@changeid Signed-off-by:
-
Brian Norris authored
The Gru-Scarlet family includes a variety of SKU identifiers, using parts of a 3-bit space {0..7}. SKU2 and SKU4 devices (under a few different manufacturer names) also use the Innolux display. For reference, the original vendor tree source: CHROMIUM: arm64: dts: rockchip: add sku{0,2,4} compatibility https://chromium.googlesource.com/chromiumos/third_party/kernel/+/f6ed665c9e2eb37fb2680debbb36ec9fb0e8fb97 CHROMIUM: arm64: dts: rockchip: scarlet: add SKU0 device tree https://chromium.googlesource.com/chromiumos/third_party/kernel/+/9987c8776f4b087d135d761e59f7fa6cc83fc7fc Signed-off-by:
-
- Sep 14, 2022
-
-
Hugh Cole-Baker authored
Define the memory region on RK3399 VOPs containing the gamma LUT at base+0x2000. Signed-off-by:
Hugh Cole-Baker <sigmaris@gmail.com> Tested-by:
Linus Heckemann <git@sphalerite.org> Link: https://lore.kernel.org/r/20211019215843.42718-4-sigmaris@gmail.com Signed-off-by:
-
Furkan Kardame authored
Add the device tree nodes to enable video output on the Station M2. Enable the GPU and HDMI nodes and fix the GPU regulator range. Signed-off-by:
Furkan Kardame <f.kardame@manjaro.org> Link: https://lore.kernel.org/r/20220627202208.45770-1-f.kardame@manjaro.org Signed-off-by:
-
- Sep 10, 2022
-
-
Judy Hsiao authored
We discoverd that the state of BCLK on, LRCLK off and SD_MODE on may cause the speaker melting issue. Removing LRCLK while BCLK is present can cause unexpected output behavior including a large DC output voltage as described in the Max98357a datasheet. In order to: 1. prevent BCLK from turning on by other component. 2. keep BCLK and LRCLK being present at the same time This patch adjusts the device tree to allow BCLK to switch to GPIO func before LRCLK output, and switch back during LRCLK is output. Signed-off-by:
Judy Hsiao <judyhsiao@chromium.org> Reviewed-by:
-
Nicolas Frattaroli authored
The RK3566 and RK3568 come with a dedicated Hantro instance solely for encoding. This patch adds a node for this to the device tree, along with a node for its MMU. Signed-off-by:
-
Piotr Oniszczuk authored
RK356x has Hantro G1 video decoder capable to decode MPEG2/H.264/VP8 video formats. This patch enables RK356x video decoder in RK356x device-tree include. Tested on [1] with FFmpeg v4l2_request code taken from [2] with MPEG2, H.642 and VP8 samples with results [3]. [1] https://github.com/warpme/minimyth2 [2] https://github.com/LibreELEC/LibreELEC.tv/blob/master/packages/multimedia/ffmpeg/patches/v4l2-request/ffmpeg-001-v4l2-request.patch [3] https://github.com/warpme/minimyth2/blob/master/video-test-summary.txt Signed-off-by:
Piotr Oniszczuk <piotr.oniszczuk@gmail.com> Reviewed-by:
Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Link: https://lore.kernel.org/r/20220214212955.1178947-2-piotr.oniszczuk@gmail.com Signed-off-by:
-
Chukun Pan authored
Add the nodes to enable the PCIe controller on the Radxa ROCK3 Model A board. Run test with the MT7921 pcie wireless card. Signed-off-by:
Chukun Pan <amadeus@jmu.edu.cn> Link: https://lore.kernel.org/r/20220726023516.6487-1-amadeus@jmu.edu.cn Signed-off-by:
-
Chukun Pan authored
Add devicetree node for hym8563 rtc to Radxa ROCK3 Model A board. Signed-off-by:
-
Nicolas Frattaroli authored
This adds the regulator node to the quartz64-b device tree, and enables the PCIe 2 controller and combphy for it. Signed-off-by:
-
Chris Morgan authored
Anbernic RG353P and RG503 are both RK3566 based handheld gaming devices from Anbernic. Both devices have: - 2 SDMMC slots. - A Realtek rtl8821cs WiFi/Bluetooth adapter. - A mini HDMI port. - A USB C host port and a USB C otg port (currently only working as device). - Multiple GPIO buttons and a single ADC button. - Dual analog joysticks controlled via a GPIO mux. - A headphone jack with amplified stereo speakers via a SGM4865 amp. - A PWM based vibrator for force feedback. The RG353P has: - 2GB LPDDR4 RAM. - A 32GB eMMC. - A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c controlled touchscreen (touchscreen is a Hynitron CST340). The RG503 has: - 1GB LPDDR4 RAM. - A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung with part number ams495qa04. Data for this panel is provided via the DSI interface, however commands are sent via a 9-bit 3-wire SPI interface. The MISO pin of SPI3 of the SOC is wired to the input of the panel, so it must be bitbanged. This devicetree enables the following hardware: - HDMI (plus audio). - Analog audio, including speakers. - All buttons. - All SDMMC/eMMC/SDIO controllers. - The ADC joysticks (note a pending patch is required to use them). - WiFi/Bluetooth (note out of tree drivers are required). - The PWM based vibrator motor. The following hardware is not enabled: - The display panels (drivers are being written and there are issues with the upstream DSI and VOP2 subsystems). - Battery (driver pending). - Touchscreen on the RG353P (note the i2c2 bus is enabled for it). Signed-off-by:
-
Chris Morgan authored
Add entry for the Anbernic RG353P and RG503 handheld devices. Signed-off-by:
-
Chris Morgan authored
Anbernic designs and manufactures portable gaming systems. https://anbernic.com/ Signed-off-by:
-
Frank Wunderlich authored
Add -regulator suffix to regulator names on Banana Pi R2 Pro board as discussed on Mailinglist Signed-off-by:
Frank Wunderlich <frank-w@public-files.de> Reviewed-by:
-
FUKAUMI Naoki authored
add support for user LEDs on Radxa ROCK 4C+ board. Signed-off-by:
-
FUKAUMI Naoki authored
only user_led2 (blue) is supported. user_led1 (green) is not connected to any gpio so it cannot be controlled. Signed-off-by:
-
Chris Morgan authored
Add the new rk817 charger driver to the Odroid Go Advance. Create a monitored battery node as well for the charger to use. All values from monitored battery are gathered from the BSP kernel for the Odroid Go Advance provided by HardKernel. Signed-off-by:
Maya Matuszczyk <maccraft123mc@gmail.com> Link: https://lore.kernel.org/r/20220827021623.23829-5-macroalpha82@gmail.com Signed-off-by:
-
- Sep 06, 2022
-
-
Ondrej Jirman authored
Voltage constraints on vccio_sd are invalid. They don't match the voltages that LDO9 can generate, and this causes rk808-regulator driver to fail to probe with -EINVAL when it tries to apply the constraints during boot. Fix the constraints to something that LDO9 can be actually configured for. Fixes: 78a21c7d ("arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro") Signed-off-by:
Ondrej Jirman <megi@xff.cz> Reviewed-by:
Caleb Connolly <kc@postmarketos.org> Reviewed-by:
Tom Fitzhenry <tom@tom-fitzhenry.me.uk> Tested-by:
-
- Sep 05, 2022
-
-
Jagan Teki authored
Add support for Radxa ROCK 4C+ SBC. Key differences of 4C+ compared to previous ROCK Pi 4. - Rockchip RK3399-T SoC - DP from 4C replaced with micro HDMI 2K@60fps - 4-lane MIPI DSI with 1920*1080 - RK817 Audio codec Also, an official naming convention from Radxa mention to remove Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not Radxa ROCK Pi 4C+. Signed-off-by:
Stephen Chen <stephen@radxa.com> Signed-off-by:
Manoj Sai <abbaraju.manojsai@amarulasolutions.com> Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Link: https://lore.kernel.org/r/20220902065057.97425-3-jagan@amarulasolutions.com Signed-off-by:
-
Jagan Teki authored
RK3399-T is down-clocked version of RK3399 SoC operated at 1.5GHz. Add CPU operating points table for it. Signed-off-by:
-
Jagan Teki authored
Document the dt-bindings for Radxa ROCK 4C+ SBC. Key differences of 4C+ compared to previous ROCK Pi 4. - Rockchip RK3399-T SoC - DP from 4C replaced with micro HDMI 2K@60fps - 4-lane MIPI DSI with 1920*1080 - RK817 Audio codec Also, an official naming convention from Radxa mention to remove Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not Radxa ROCK Pi 4C+. Acked-by:
-
Martijn Braam authored
This is a basic DT containing regulators and UART, intended to be a base that myself and others can add additional nodes in future patches. Tested to work: booting from eMMC/SD, output over UART. https://wiki.pine64.org/wiki/PinePhone_Pro This is derived from the community pine64-org repo[0] with fixes from https://megous.com/git/linux. 0. https://gitlab.com/pine64-org/linux/-/commit/261d3b5f8ac503f97da810986d1d6422430c8531 Signed-off-by:
Martijn Braam <martijn@brixit.nl> Co-developed-by:
Kamil Trzciński <ayufan@ayufan.eu> [no SoB, but Kamil is happy for this patch to be submitted] Co-developed-by:
Nícolas F. R. A. Prado <n@nfraprado.net> Tested-by:
-
Tom Fitzhenry authored
Document board compatible names for Pine64 PinePhonePro. https://wiki.pine64.org/wiki/PinePhone_Pro Signed-off-by:
-
Andy Yan authored
EAIDK-610 is from OPEN AI LAB and popularly used by university students. Specification: - Rockchip RK3399 - LPDDR3 4GB - TF sd scard slot - eMMC - AP6255 for WiFi + BT - Gigabit ethernet - HDMI out - 40 pin header - USB 2.0 x 2 - USB 3.0 x 1 - USB 3.0 Type-C x 1 - 12V DC Power supply This patch is test on Armbain and Glodroid with HDMI/GPU/USB HOST/Type-C ADB/WIFI/BT. Signed-off-by:
Andy Yan <andyshrk@163.com> Link: https://lore.kernel.org/r/20220709103016.2754044-1-andyshrk@163.com Signed-off-by:
-
Andy Yan authored
EAIDK-610 is a rk3399 based board from OPEN AI LAB and popularly used by university students. Specification: - Rockchip RK3399 - LPDDR3 4GB - TF sd scard slot - eMMC - AP6255 for WiFi + BT - Gigabit ethernet - HDMI out - 40 pin header - USB 2.0 x 2 - USB 3.0 x 1 - USB 3.0 Type-C x 1 - 12V DC Power supply Signed-off-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220709103001.2753992-1-andyshrk@163.com Signed-off-by:
-
Andy Yan authored
Add vendor prefixes for OPEN AI LAB. Signed-off-by:
-
Michael Riesch authored
Add the MIPI CSI DPHY node to the RK356x device tree. Signed-off-by:
-
- Sep 04, 2022
-
-
Frank Wunderlich authored
Add Nodes to Bananapi-R2-Pro board to support PCIe v3 and set PCIe related regulators to always on. Suggested-by:
Peter Geis <pgwipeout@gmail.com> Signed-off-by:
-
Frank Wunderlich authored
Add nodes to rk356x devicetree to support PCIe v3. Signed-off-by:
-
- Aug 29, 2022
-
-
Michael Riesch authored
On the Radxa ROCK3 Model A the I2C adapters related to the MIPI DSI connector and the M.2/NGFF connector use the non-default pins. Specify the correct pinctrl but leave the adapters disabled (as they are supposed to be activated by overlays that describe the external hardware). Signed-off-by:
-
Michael Riesch authored
The Radxa ROCK3 Model A features a voltage regulator that provides a 3V3 supply to the MIPI DSI connector. Add this regulator to the device tree of the board. Signed-off-by:
-
Michael Riesch authored
The Radxa ROCK3 Model A features a voltage regulator that provides a 3V3 supply to the MIPI CSI connector. Add this regulator to the device tree of the board. Signed-off-by:
-
