- Nov 30, 2009
-
-
David Hunter authored
The shift operator used here to convert from bytes to 32-bit words is backwards. Signed-off-by:
David Hunter <hunterd42@gmail.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com>
-
Li Yang authored
Symptom: device_suspend(): mtd_cls_suspend+0x0/0x58 returns -11 PM: Device mtd14 failed to suspend: error -11 PM: Some devices failed to suspend This patch enables other chips to be suspended if the active chip of the controller has been suspended. Signed-off-by:
Jin Qing <b24347@freescale.com> Signed-off-by:
Li Yang <leoli@freescale.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Guillaume LECERF authored
SST 39VF160x/39VF320x and some old SST chips need a special command sequence to enter CFI QueRY mode [1]. This patch adds the relevant sequence to cfi_qry_mode_on(). Tested with 39VF3201. Signed-off-by:
Guillaume LECERF <glecerf@gmail.com> Signed-off-by:
-
Ladislav Michl authored
This one sits in my tree for more than two years... Using device code found on page 12 (http://www.btdesigner.com/pdfs/M29W800D.pdf ) and unlock address from page 15 MTD subsytem happily detects ST M29W800DB in 16-bit mode. I do believe original author used only 8-bit mode and thus didn't hit this bug. Signed-off-by:
Ladislav Michl <ladis@linux-mips.org> Signed-off-by:
-
KOSAKI Motohiro authored
Non MM subsystem must not use PF_MEMALLOC. Memory reclaim need few memory, anyone must not prevent it. Otherwise the system cause mysterious hang-up and/or OOM Killer invokation. Signed-off-by:
KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by:
-
Mark A. Greer authored
The existing NAND infrastructure allows the default main and mirror bad block tables to be overridden in nand_default_bbt(). However, the davinci_nand driver does not support this. Add that support by adding fields to the davinci driver's platform data so platform code can pass in their own bbt's and make the davinci_nand driver honor them. Signed-off-by:
Mark A. Greer <mgreer@mvista.com> Signed-off-by:
Kevin Hilman <khilman@deeprootsystems.com> CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by:
-
Anton Vorontsov authored
CAT25 chips (as manufactured by On Semiconductor, previously Catalyst Semiconductor) are similar to the original M25Px0 chips, except: - Address width can vary (1-2 bytes, in contrast to 3 bytes in M25P chips). So, implement convenient m25p_addr2cmd() and m25p_cmdsz() calls, and place address width information into flash_info struct; - Page size can vary, therefore we shouldn't hardcode it, so get rid of FLASH_PAGESIZE definition, and place the page size information into flash_info struct; - CAT25 EEPROMs don't need to be erased, so add NO_ERASE flag, and propagate it to the mtd subsystem. [dwmw2: Fix up for conflicts with DMA safety patch] Signed-off-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by:
-
Anton Vorontsov authored
Previosly the driver always tried JEDEC probing, assuming that non-JEDEC chips will return '0'. But truly non-JEDEC chips (like CAT25) won't do that, their behaviour on RDID command is undefined, so the driver should not call jedec_probe() for these chips. Also, be less strict on error conditions, don't fail to probe if JEDEC found a chip that is different from what platform code told, instead just print some warnings and use an information obtained via JEDEC. In that case we should not trust partitions any longer, but they might be still useful (i.e. they could protect some parts of the chip). Signed-off-by:
-
Anton Vorontsov authored
This patch converts the m25p80 driver so that now it uses .id_table for device matching, making it properly detect devices on OpenFirmware platforms (prior to this patch the driver misdetected non-JEDEC chips, seeing all chips as "m25p80"). Also, now jedec_probe() only does jedec probing, nothing else. If it is not able to detect a chip, NULL is returned and the driver fall backs to the information specified by the platform (platform_data, or exact ID). Signed-off-by:
-
Artem Bityutskiy authored
The mtd_pagetest test did not initialize the pgsize variable, which basically means it did not work. This problem was reported by Török Edwin <edwintorok@gmail.com> Signed-off-by:
Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by:
-
Uwe Kleine-König authored
The function mxcnd_remove is defined using __devexit, so don't use __exit_p but __devexit_p to wrap it. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Uwe Kleine-König authored
The function excite_nand_remove is used only wrapped by __devexit_p so define it using __devexit. Signed-off-by:
-
Roel Kluin authored
MAX_SUMMARY_SIZE was meant as a limit, not as a minimum Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Joakim Tjernlund authored
Erase-suspend for writing is required to avoid blocking applications that wish to write some data (to a NOR block other than the one being erased). Particularly, it solves some huge delays that an application (which writes to a UBIFS) will experience if UBI attaches to empty NOR flash. In this case the UBI background thread will erase a lot of blocks and the application can be blocked for minutes because of the "MTD/CFI chip lock". This feature has been disabled for years. Maybe this was because the old code turned it on for erase-suspend read-only chips also (cfip->EraseSuspend & 0x1). This is wrong and corrected now. This patch was tweaked by Norbert van Bolhuis. Signed-off-by:
Norbert van Bolhuis <nvbolhuis@aimvalley.nl> Signed-off-by:
-
Scott Wood authored
We want error information even if the kernel hasn't been built for verbose debugging. Signed-off-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
-
Scott Wood authored
Currently, the program and erase sequences do not wait for completion, instead relying on a subsequent waitfunc() callback. However, this causes the chipselect to be deasserted while the NAND chip is still asserting the busy pin, which can corrupt activity on other chipselects. This patch switches to using the sequences recommended by the manual, in which a wait is performed within the initial command sequence. We can now re-use the status byte from the initial command sequence, rather than having to do another status read in the waitfunc. Since we're already touching the command sequences, it also cleans up some cruft in SEQIN that isn't needed since we cannot program partial pages outside of OOB. Signed-off-by:
Suchit Lepcha <suchit.lepcha@freescale.com> Signed-off-by:
-
Scott Wood authored
When a NAND operation is in progress, all other localbus operations (including NOR flash) will have to wait for access to the bus. However, the NAND operation may take longer to complete than the default timeout. Thus, if NOR is accessed while a NAND operation is in progress, the NAND operation will fail. Signed-off-by:
-
Akinobu Mita authored
Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Roel Kluin authored
The returned error should stay negative Signed-off-by:
-
Roel Kluin authored
Return a negative error value instead of a positive Signed-off-by:
-
Hans-Christian Egtvedt authored
This patch moves the MANUFACTURER_ST and MANUFACTURER_INTEL to the include/linux/mtd/cfi.h header file and renames them to CFI_MFR_ST and CFI_MFR_INTEL. CFI_MFR_ST was already present there. All references in drivers/mtd/chips/cfi_cmdset_0001.c are updated to reflect this. Signed-off-by:
Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Acked-by:
Nicolas Pitre <nico@fluxnic.net> Signed-off-by:
-
Hans-Christian Egtvedt authored
This patch sets the MTD_POWERUP_LOCK flag for AT49BV640D and AT49BV640DT devices, since the devices are locked when powered up and needs to be unlocked before interfaced. Quote datasheet; "At power-up and reset, all sectors have their Softlock protection mode enabled.". Tested on AVR32 hardware platform with an AT49BV640D flash device. Signed-off-by:
-
Roel Kluin authored
The index is signed, make sure it is not negative when we read the array element. Signed-off-by:
-
Johannes Stezenbach authored
spi_write() requires the buffer to be DMA-safe, kmalloc() it seperately to ensure this. Signed-off-by:
Johannes Stezenbach <js@sig21.net> Signed-off-by:
-
Ben Dooks authored
Update the nand information passed to the core from the platform data to setup the initial option value, so that flags such as NAND_SCAN_SILENT_NODEV can pass through. Signed-off-by:
Ben Dooks <ben@simtec.co.uk> Signed-off-by:
Simtec Linux Team <linux@simtec.co.uk> Signed-off-by:
-
Ben Dooks authored
Add NAND_SCAN_SILENT_NODEV to chip->options to the user-worrying messages 'No NAND device found!!!'. This message often worries users (was three exclamation marks really necessary?) and especially in systems such as the Simtec Osiris where there may be optional NAND devices which are not known until probe time. Revised version of the original NAND_PROBE_SPECULATIVE patch after comments by Artem Bityutskiy about adding a whole new call. Signed-off-by:
-
Atsushi Nemoto authored
This patch fixes memory leak on chip->bbt and chip->buffers. Signed-off-by:
Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by:
-
Tobias Klauser authored
Use the resource_size inline function instead of manually calculating the resource size. This reduces the chance of introducing off-by-one errors. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Signed-off-by:
-
Simon Kagstrom authored
This is a quick and dirty patch to add panic_write for NAND flashes. The patch seems to work OK on my CRIS board running a 2.6.26 kernel with a ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit), and also on a OpenRD base (Marvell Kirkwood) board with a Toshiba NAND 512MiB 3,3V 8-bit flash with 2.6.32-pre1. Signed-off-by:
Edgar E. Iglesias <edgar@axis.com> Signed-off-by:
Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by:
-
Nicolas Pitre authored
Signed-off-by:
-
Mika Korhonen authored
Signed-off-by:
Mika Korhonen <ext-mika.2.korhonen@nokia.com> Reviewed-by:
Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by:
-
Mika Korhonen authored
Add support for multiblock erase command. OneNANDs (excluding Flex-OneNAND) are capable of simultaneous erase of up to 64 eraseblocks which is much faster. This changes the erase requests for regions covering multiple eraseblocks to be performed using multiblock erase. Signed-off-by:
-
Mika Korhonen authored
Separate the actual execution of erase to a new function: onenand_block_by_block_erase(). This is done in preparation for the multiblock erase support. Signed-off-by:
-
Akinobu Mita authored
This module tests NAND ECC functions. The test is simple. 1. Create a 256 or 512 bytes block of data filled with random bytes (data) 2. Duplicate the data block and inject single bit error (error_data) 3. Try to correct error_data 4. Compare data and error_data Signed-off-by:
Vimal Singh <vimalsingh@ti.com> Signed-off-by:
-
Akinobu Mita authored
Add __nand_calculate_ecc() which does not take struct mtd_info. The built-in 256/512 software ECC calculation and correction tester will use it. Signed-off-by:
-
Amul Kumar Saha authored
What is OTP in OneNAND? The device includes, 1. one block-sized OTP (One Time Programmable) area and 2. user-controlled 1st block OTP(Block 0) that can be used to increase system security or to provide identification capabilities. What is done? In OneNAND, one block of the NAND Array is set aside as an OTP memory area, and 1st Block (Block 0) can be used as OTP area. This area, available to the user, can be configured and locked with secured user information. The OTP block can be read, programmed and locked using the same operations as any other NAND Flash Array memory block. After issuing an OTP-Lock, OTP block cannot be erased. OTP block is fully-guaranteed to be a good block. Why it is done? Locking the 1st Block OTP has the effect of a 'Write-protect' to guard against accidental re-programming of data stored in the 1st block and OTP Block. Which problem it solves? OTP support is provided in the existing implementation of OneNAND/Flex-OneNAND driver, but it is not working with OneNAND devices. Have observed the following in current OTP OneNAND Implmentation, 1. DataSheet specific sequence to lock the OTP Area is not followed. 2. Certain functions are quiet generic to cope with OTP specific activity. This patch re-implements OTP support for OneNAND device. How it is done? For all blocks, 8th word is available to the user. However, in case of OTP Block, 8th word of sector 0, page 0 is reserved as OTP Locking Bit area. Therefore, in case of OTP Block, user usage on this area is prohibited. Condition specific values are entered in the 8th word, sector0, page 0 of the OTP block during the process of issuing an OTP-Lock. The possible conditions are: 1. Only 1st Block Lock 2. Only OTP Block Lock 3. Lock both the 1st Block and the OTP Block What Other feature additions have been done in this patch? This patch adds feature for: 1. Only 1st Block Lock 2. Lock both the 1st Block and the OTP Blocks Re-implemented OTP support for OneNAND Added following features to OneNAND 1. Lock only 1st Block in OneNAND 2. Lock BOTH 1st Block and OTP Block in OneNAND [comments were slightly tweaked by Artem] Signed-off-by:
Amul Kumar Saha <amul.saha@samsung.com> Reviewed-by:
-
- Nov 20, 2009
-
-
Akinobu Mita authored
Use hweight_long instead of Brian Kernighan's/Peter Wegner's method Signed-off-by:
-
- Oct 21, 2009
-
-
H Hartley Sweeten authored
Commit 4b56ffca ("mtd: Fix kernel NULL pointer dereference in physmap.c") introduced a couple of bugs. It neglected to run the loop of map_destroy() calls in physmap_flash_remove(), if !info->cmtd, which would happen if that function was called to clean up errors during probe. It also failed to compile if CONFIG_MTD_PARTITIONS was not defined. Reported-By:
H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by:
-
- Oct 20, 2009
-
-
David Woodhouse authored
This reverts commit 71b7d0d9 . The problem which that commit attempted to fix was a bootloader issue, which had been misunderstood. The 'fix' causes lots of false bad blocks for existing users with sane firmware. Thanks to Mathieu Berland for diagnosing the problem coherently. Signed-off-by:
-
hartleys authored
In register_mtd_blktrans(), the symbol 'ret' is already declared as an int at the start of the function. The inner loop declaration is unnecessary. Quiets the following sparse warning: warning: symbol 'ret' shadows an earlier one Signed-off-by:
-
