Make the driver be able to bit-bang a GPIO for the Chip Select pin of
select peripherals.

The GPIO value is driven by the driver in that case, and none of the
hardware Chip Select bits will be populated in the PUSHR register for
the TX commands constructed for this peripheral.

Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221111211356.545026-1-vladimir.oltean@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The timeout value of the current dma read is unreasonable. For example,
If the spi flash clock is 26Mhz, It will takes about 1.3ms to read a
4KB data in spi mode. But the actual measurement exceeds 50s when a
dma read timeout is encountered.

In order to be more accurately, It is necessary to use usecs_to_jiffies,
After modification, the measured timeout value is about 130ms.

Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221114081327.25750-1-bayi.cheng@mediatek.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Mixing SPI slave/target handlers and SPI slave/target controllers using
legacy and modern naming does not work well: there are now two different
callbacks for aborting a slave/target operation, of which only one is
populated, while spi_{slave,target}_abort() check and use only one,
which may be the unpopulated one.

Fix this by merging the slave/target abort callbacks into a single
callback using a union, like is already done for the slave/target flags.

Fixes: b8d3b056

 ("spi: introduce new helpers with using modern naming")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/809c82d54b85dd87ef7ee69fc93016085be85cec.1667555967.git.geert+renesas@glider.be


Signed-off-by: Mark Brown <broonie@kernel.org>

Simple typo, simple fix.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221103190052.915755-1-j.neuschaefer@gmx.net


Signed-off-by: Mark Brown <broonie@kernel.org>

Don't populate the const array ls1028a_soc_attr on the stack, instead
make it static. Also makes the object code smaller.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20221102152904.143423-1-colin.i.king@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

For using modern names host/target to instead of all the legacy names,
I think it takes 3 steps:
  - step1: introduce new helpers with modern naming.
  - step2: switch to use these new helpers in all drivers.
  - step3: remove all legacy helpers and update all legacy names.

This patch is for step1, it introduces new helpers with host/target
naming for drivers using.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221011092204.950288-1-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

struct spi_master has been renamed to struct spi_controller. Update the
reference in spi.rst to make it clickable again.

Fixes: 8caab75f

 ("spi: Generalize SPI "master" to "controller"")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221101173252.1069294-1-j.neuschaefer@gmx.net


Signed-off-by: Mark Brown <broonie@kernel.org>

The node name for flash memories has been standardized to "flash@...".
Fix the example in nuvoton,npcm-fiu.txt accordingly.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221031222559.199509-1-j.neuschaefer@gmx.net


Signed-off-by: Mark Brown <broonie@kernel.org>

Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221029071720.3041094-1-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221029071529.3019626-1-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.

Convert to the regular interface.

Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221026122951.331638-1-bigeasy@linutronix.de


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:

Currently the SPI PXA2xx devices on Intel platforms can be instantiated
via the following paths:
 1) as ACPI LPSS device on Haswell, Bay Trail and Cherry Trail;
 2) as ACPI LPSS device on the Sky Lake and newer;
 3) as PCI LPSS device on Haswell, Bay Trail and Cherry Trail;
 4) as PCI LPSS device on the Sky Lake and newer;
 5) as PCI device via ID table.

Each of these cases provides some platform related data differently,
i.e.:
 1) via drivers/acpi/acpi_lpss.c and drivers/spi/spi-pxa2xx.c
 2) via drivers/mfd/intel-lpss-acpi.c
 3) via drivers/spi/spi-pxa2xx-pci.c
 4) via drivers/mfd/intel-lpss-pci.c and drivers/spi/spi-pxa2xx.c
 5) via drivers/spi/spi-pxa2xx-pci.c

This approach has two downsides:

a) there is no data propagated in the case #2 because we can't have
   two or more drivers to match the same ACPI ID and hence some cases
   are still not supported (Sky Lake and newer ACPI enabled LPSS);

b) the data is duplicated over two drivers in the cases #1 & #4 and,
   besides to be a bloatware, it is error prone (e.g. Lakefield has
   a wrong data right now due to missed PCI entry in the spi-pxa2xx.c).

This series fixes the downsides, and enables previously unsupported
cases.

There is no code that uses ID tables directly, except the
struct device_driver at the end of the file. Hence, move
tables closer to its user. It's always possible to access
them via pointer to a platform device.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20221021190018.63646-5-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Since the PCI enumerated devices provide a property with SSP type,
there is no more necessity to bear the copy of the ID table here.
Remove it for good.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-4-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Allow to set the Intel SSP type by reading the property.
Only apply this to the known MFD enumerated LPSS devices.

The check is done by the looking for the specifically
named IO memory resource provided by upper layer. This
won't be an issue in the future because we strictly
prioritize the order in which we are looking for the SSP
type in the code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-3-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Currently we blindly apply the SSP type value from any source of the
information. Increase robustness by validating the value before use.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-2-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Use the devm_platform_{get_and_}ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource() separately.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019092635.1176622-1-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Amjad Ouled-Ameur <aouledameur@baylibre.com>:

Between SPI transactions, all SPI pins are in HiZ state. When using the SS
signal from the SPICC controller it's not an issue because when the
transaction resumes all pins come back to the right state at the same time
as SS.

The problem is when we use CS as a GPIO. In fact, between the GPIO CS
state change and SPI pins state change from idle, you can have a missing or
spurious clock transition.

Set a bias on the clock depending on the clock polarity requested before CS
goes active, by passing a special "idle-low" and "idle-high" pinctrl state
and setting the right state at a start of a message.

Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:

This series has a couple of cleanups for the pxa2xx driver.

Between SPI transactions, all SPI pins are in HiZ state. When using the SS
signal from the SPICC controller it's not an issue because when the
transaction resumes all pins come back to the right state at the same time
as SS.

The problem is when we use CS as a GPIO. In fact, between the GPIO CS
state change and SPI pins state change from idle, you can have a missing or
spurious clock transition.

Set a bias on the clock depending on the clock polarity requested before CS
goes active, by passing a special "idle-low" and "idle-high" pinctrl state
and setting the right state at a start of a message

Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Link: https://lore.kernel.org/r/20221004-up-aml-fix-spi-v4-2-0342d8e10c49@baylibre.com


Signed-off-by: Mark Brown <broonie@kernel.org>

SPI pins of the SPICC Controller in Meson-GX needs to be controlled by
pin biais when idle. Therefore define three pinctrl names:
- default: SPI pins are controlled by spi function.
- idle-high: SCLK pin is pulled-up, but MOSI/MISO are still controlled
by spi function.
- idle-low: SCLK pin is pulled-down, but MOSI/MISO are still controlled
by spi function.

Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221004-up-aml-fix-spi-v4-1-0342d8e10c49@baylibre.com


Signed-off-by: Mark Brown <broonie@kernel.org>

In commit 7a908832

 ("spi: imx: add fallback feature") the last
user of the struct spi_imx_devtype_data::disable_dma callback was
removed. However the disable_dma member of struct spi_imx_devtype_data
and the callback itself was not removed.

Remove struct spi_imx_devtype_data::disable_dma and mx51_disable_dma()
as they are unused.

Cc: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20221021131051.1777984-1-mkl@pengutronix.de


Signed-off-by: Mark Brown <broonie@kernel.org>

Cleaning up the driver to use pm_ptr() macro instead of ifdeffery
that makes it simpler and allows the compiler to remove those functions
if built without CONFIG_PM and CONFIG_PM_SLEEP support.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20221020194500.10225-6-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

We have a temporary variable to keep a pointer to a struct device in
the pxa2xx_spi_init_pdata(). Use it consistently there.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020194500.10225-5-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:

A bunch of improvements to the driver:

- Fix kernel-doc warnings in GQSPI driver.
- Avoid setting CPOL, CPHA & baud rate multiple times.
- Add Versal platform support in GQSPI driver.
- Add tap delay support in GQSPI driver.

Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019093318.1183190-1-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add tap delay support for GQSPI controller on Versal platform.

Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-8-amit.kumar-mahapatra@amd.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add new compatible to support QSPI controller on Xilinx Versal SoCs.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221011062040.12116-7-amit.kumar-mahapatra@amd.com


Signed-off-by: Mark Brown <broonie@kernel.org>

GQSPI controller uses the internal clock for loopback mode. The loopback
mode is used with the high-speed Quad SPI timing mode, where the memory
interface clock needs to be greater than 40 MHz. Based on the tap delay
value programmed, the internal clock is delayed and used for capturing
the data.
Based upon the frequency of operation set the recommended tap delay
values in GQSPI driver.

Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-6-amit.kumar-mahapatra@amd.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add support for QSPI ioctl functions and enums.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-5-amit.kumar-mahapatra@amd.com


Signed-off-by: Mark Brown <broonie@kernel.org>

During every transfer the GQSPI driver configures the baud rate value. But
when there is no change in the SPI clock frequency the driver should avoid
rewriting the same baud rate value to the configuration register. Update
GQSPI driver to rewrite the baud rate value if there is any change in SPI
clock frequency.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-4-amit.kumar-mahapatra@amd.com


Signed-off-by: Mark Brown <broonie@kernel.org>

During every transfer GQSPI driver writes the CPOL & CPHA values to the
configuration register. But the CPOL & CPHA values do not change in between
multiple transfers, so moved the CPOL & CPHA initialization to hardware
init so that the values are written only once.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-3-amit.kumar-mahapatra@amd.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Document zynqmp_qspi ctrl and op_lock member description. It also adds
return documentation for 'zynqmp_qspi_setuprxdma' and zynqmp_qspi_read_op.

Fixes below kernel-doc warnings-

spi-zynqmp-gqspi.c:178: warning: Function parameter or member 'ctlr' not
described in 'zynqmp_qspi'
spi-zynqmp-gqspi.c:178: warning: Function parameter or member 'op_lock'
not described in 'zynqmp_qspi'

spi-zynqmp-gqspi.c:737: warning: No description found for return value of
'zynqmp_qspi_setuprxdma'
spi-zynqmp-gqspi.c:822: warning: No description found for return value of
'zynqmp_qspi_read_op'

Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-2-amit.kumar-mahapatra@amd.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Not all zero page implementations use empty_zero_page global pointer so
let's substitute empty_zero_page occurence with helper ZERO_PAGE(0).

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Link: https://lore.kernel.org/r/20221018215755.33566-2-giulio.benetti@benettiengineering.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The function bcm_qspi_remove() returns zero unconditionally. Make it
return void.

This is a preparation for making platform remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221017200143.1426528-1-u.kleine-koenig@pengutronix.de


Signed-off-by: Mark Brown <broonie@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.

No functional changes.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221017171243.57078-1-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Use the devm_platform_{get_and}_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource() separately.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145852.1882221-2-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145852.1882221-1-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Microchip pci1xxxx is a PCIe switch with a multi-function endpoint on one of its
downstream ports. SPI is one of the functions in the multi-function endpoint. This
function has 2 SPI masters, operates at a maximum frequency of 30 MHz and supports
7 client devices per master. This patch adds complete functionality to the SPI
function except for suspend and resume.

Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20221006050514.115564-2-tharunkumar.pasumarthi@microchip.com


Signed-off-by: Mark Brown <broonie@kernel.org>