Some PHYs will report that the link is up even though there is a fault
condition.  Therefore, check the fault flag too.  We must also read
STAT2 to reset this flag.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

falcon_reset_xaui() waits for XGXS reset to complete, but the XAUI
serdes reset may take longer.  It needs to check both reset active
bits.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We must call netif_carrier_off() after the device is registered, not
before, to set the operational state and user-space IFF_RUNNING flag
correctly.

Since we don't want observers to see an intermediate state, open-code
register_netdev() and add efx_update_name() and netif_carrier_off()
into the locked region.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If nothing has been written into the qeth sysfs-attribute layer2,
its value is "-1" meaning "not yet defined". But the value is
displayed as "1" meaning "layer2 selected". The patch changes the
reading of this "-1"-value to "-1" to make clear the layer2-attribute
has not yet been defined.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth displayed an entry in /proc/service_level even when no valid
MCL-string was available (the MCL info is blank). The change is to
create an entry in /proc/service_level only when MCL-string is
non-zero.

Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clear separation of cast-type determination (send path) for layer-2
resp. layer-3. Allowing to have inline functions for qeth layer-
discipline.

Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case the IP address list contains entries (not removed when the device was set
offline) this entries should be registered next time the device is brought online.
In the past this was done implicitly with the device open call but since we wait
in the set IPv4 IPA and the device open common code holds various locks this
does not work any longer.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Qeth HiperSockets support now retries sending of packets when the
IBM System z signals a temporary resource shortage (e.g. target
buffer full). The packet is enqueued into the device queue.
After 3 times of unsuccessful send the packet is dropped.

Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steven Rostedt has suggested that Neil work with the tracing
folks, trying to use TRACE_EVENT as the mechanism for
implementation.  And if that doesn't workout we can investigate
other solutions such as that one which was tried here.

This reverts the following 2 commits:

5a165657
("net: skb ftracer - Add config option to enable new ftracer (v3)")

9ec04da7


("net: skb ftracer - Add actual ftrace code to kernel (v3)")

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.100.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This brings the 57780's phy into IEEE compliance by suppressing the
common mode oscillation.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the AC131 fast ethernet transceiver.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the BCM50610M phy ID.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch converts the code to use the PHY_IS_FET flag rather than the
ASIC revision to decide whether or not to use FET paths.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Broadcom's phys come in two distinctly different register layouts.  For
the lack of an official term to distinguish between the two formats, we
can loosely categorize them by their fast ethernet or gigabit ethernet
transceiver description.  This patch creates the (driver-internal) Fast
Ethernet Transceiver (FET) namespace and converts the 5906 EPHY
definitions over.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch tunes the timeouts the CPMU uses to decide when to switch
from the clocks output by the PHY to internal clock sources.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the 57788 and removes support for the 57720
which was never released.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most older tg3 devices only supported a PCIe maximum payload size of
128 bytes.  More recent devices bump this limit up to 256 bytes
though.  This patch modifies the code so that the MPS limit is only
enforced on those devices that only allow the 128 byte setting.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julia Lawall discovered that the TG3_FLG2_TSO_CAPABLE flag was being
compared against the wrong flags device member.  This patch implements
the fix.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch prevents a tx BD corruption bug by preventing the device from
powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps.

The same bits are also used to prevent a system hang during chip reset
resulting from a complicated set of events that ultimately leads to
PCIe block register corruption.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes some PCIe link receiver errors by decreasing the internal
electrical idle timeout.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove function e1000_mta_set, as it is no longer called

Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were already exporting TSO6 to the vlan, but we weren't exporting the
checksum support for IPV6 which was causing warning messages to be
displayed when doing IPv6 TSO over a vlan.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have some ~40 functions that were being called out with 'make
namespacecheck'.  This patch changes these functions to be static.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix ethtool get_settings logic to report 10G & 1G advertised and
supported link modes in all 8259x 10G backplane connection types
except for 82598EB BX network connection type.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the interface is put in bridged mode, destination mac
addresses are unknown to firmware. So packets take a slow
path (lower priority) in firmware reducing performance.

Firmware can cache limited number of remote unicast mac
addresses for certain interval, if "dynamic mac learning"
mode is enabled.

Driver needs to enable this "mac learning" mode in firmware.
Currently this is done through net device class sysfs entry,
possibly this can also be done upon netlink notifications to
from bridge.

Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consolidate all MAC/PHY access functions into netxen_nic_hw.c

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement common function for locking/unlocking 8 hardware
semaphores used for serializing access to shared resouces
on a NIC board by different PCI functions.

As by definition, callers of these semaphore API can be
put to sleep till the semaphore is locked.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove code for phy access on unreleased NX2031 based quad-gig board.

NX3031 based production quad-gig boards do not require direct phy
access by driver.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of fully initializing an unusable second r6040
device, perform the PHY detection earlier and bail out
in r6040_init_one when we could not read the PHY identifier.

Signed-off-by: Mark Kelly <mark@bifferos.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the unused pioaddr variable.

Signed-off-by: Mark Kelly <mark@bifferos.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that RDS transports are no longer compiled-in to RDS core,
there is now the possibility that they will not be loaded. This
adds a helpful suggestion when rds_bind() fails to find a transport.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that transports can be loaded in arbitrary order,
it is important for rds_trans_get_preferred() to look
for them in a particular order, instead of walking the list
until it finds a transport that works for a given address.
Now, each transport registers for a specific transport slot,
and these are ordered so that preferred transports come first,
and then if they are not loaded, other transports are queried.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable the building of transports as modules.

Also, improve consistency of Kconfig messages in relation to other
protocols, and move build dependency on IB from the RDS core code
to the rds_rdma module.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that rdma and tcp transports will be modularized,
we need to export a number of functions so they can call them.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code allows RDS to be tunneled over a TCP connection.

RDMA operations are disabled when using TCP transport,
but this frees RDS from the IB/RDMA stack dependency, and allows
it to be used with standard Ethernet adapters, or in a VM.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consolidate register definitions in netxen_nic_hdr.h

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.

Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>