The MAX20086-MAX20089 are dual/quad power protectors for cameras. Add
corresponding DT bindings.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220106224350.16957-2-laurent.pinchart+renesas@ideasonboard.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The RPMh regulator driver is much newer and gets more attention, which in
consequence makes it do a few things better. Update qcom_smd-regulator's
probe function to mimic what rpmh-regulator does to address a couple of
issues:

- Probe defer now works correctly, before it used to, well,
  kinda just die.. This fixes reliable probing on (at least) PM8994,
  because Linux apparently cannot deal with supply map dependencies yet..

- Regulator data is now matched more sanely: regulator data is matched
  against each individual regulator node name and throwing an -EINVAL if
  data is missing, instead of just assuming everything is fine and
  iterating over all subsequent array members.

- status = "disabled" will now work for disabling individual regulators in
  DT. Previously it didn't seem to do much if anything at all.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20211230023442.1123424-1-konrad.dybcio@somainline.org


Signed-off-by: Mark Brown <broonie@kernel.org>

Return value from regmap_update_bits() directly instead
of taking this in another redundant variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Link: https://lore.kernel.org/r/20220104104139.601031-1-chi.minghao@zte.com.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

Receiving the Over-Current Protection interrupt while the regulator is
disabled does not count as unhandled/failure (IRQ_NONE, or 0 as it were)
but a "fake event", usually due to inrush as the is regulator about to
be enabled.

Fixes: 390af53e

 ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20211224113450.107958-1-marijn.suijten@somainline.org


Signed-off-by: Mark Brown <broonie@kernel.org>

There's no need for a fixed string like 'BUCK9' to be under
'patternProperties', so move it under 'properties' instead.

Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211221120744.1118518-1-robh@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

The TPS68470 PMIC provides Clocks, GPIOs and Regulators. At present in
the kernel the Regulators and Clocks are controlled by an OpRegion
driver designed to work with power control methods defined in ACPI, but
some platforms lack those methods, meaning drivers need to be able to
consume the resources of these chips through the usual frameworks.

This commit adds a driver for the regulators provided by the tps68470,
and is designed to bind to the platform_device registered by the
intel_skl_int3472 module.

This is based on this out of tree driver written by Intel:
https://github.com/intel/linux-intel-lts/blob/4.14/base/drivers/regulator/tps68470-regulator.c


with various cleanups added.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-6-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'platform-drivers-x86-int3472-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into regulator-5.17

Signed tag for the immutable platform-drivers-x86-int3472 branch

This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches required so that the tps68570 regulator
driver can be applied.

Return value from twlreg_write() directly instead
of taking this in another redundant variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20211213021655.435423-1-chi.minghao@zte.com.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.

To work around this info missing from the ACPI tables on devices where
the int3472 driver is used, the int3472 MFD-cell drivers attach info about
consumers to the clks/regulators when registering these.

This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.

All the sensor ACPI fw-nodes have a _DEP dependency on the INT3472 ACPI
fw-node, so to work around these probe ordering issues the ACPI core /
i2c-code does not instantiate the I2C-clients for any ACPI devices
which have a _DEP dependency on an INT3472 ACPI device until all
_DEP-s are met.

This relies on acpi_dev_clear_dependencies() getting called by the driver
for the _DEP-s when they are ready, add a acpi_dev_clear_dependencies()
call to the discrete.c probe code.

In the tps68470 case calling acpi_dev_clear_dependencies() is already done
by the acpi_gpiochip_add() call done by the driver for the GPIO MFD cell
(The GPIO cell is deliberately the last cell created to make sure the
clk + regulator cells are already instantiated when this happens).

However for proper probe ordering, the clk/regulator cells must not just
be instantiated the must be fully ready (the clks + regulators must be
registered with their subsystems).

Add MODULE_SOFTDEP dependencies for the clk and regulator drivers for
the instantiated MFD-cells so that these are loaded before us and so
that they bind immediately when the platform-devs are instantiated.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-12-hdegoede@redhat.com

Pass tps68470_regulator_platform_data to the tps68470-regulator
MFD-cell, specifying the voltages of the various regulators and
tying the regulators to the sensor supplies so that sensors which use
the TPS68470 can find their regulators.

Since the voltages and supply connections are board-specific, this
introduces a DMI matches int3472_tps68470_board_data struct which
contains the necessary per-board info.

This per-board info also includes GPIO lookup information for the
sensor IO lines which may be connected to the tps68470 GPIOs.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-11-hdegoede@redhat.com

Pass tps68470_clk_platform_data to the tps68470-clk MFD-cell,
so that sensors which use the TPS68470 can find their clock.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-10-hdegoede@redhat.com

The discrete.c code is not the only code which needs to lookup the
acpi_device and device-name for the sensor for which the INT3472
ACPI-device is a GPIO/clk/regulator provider.

The tps68470.c code also needs this functionality, so factor this
out into a new get_sensor_adev_and_name() helper.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-9-hdegoede@redhat.com

The intel_skl_int3472.ko module contains 2 separate drivers,
the int3472_discrete platform driver and the int3472_tps68470
I2C-driver.

These 2 drivers contain very little shared code, only
skl_int3472_get_acpi_buffer() and skl_int3472_fill_cldb() are
shared.

Split the module into 2 drivers, linking the little shared code
directly into both.

This will allow us to add soft-module dependencies for the
tps68470 clk, gpio and regulator drivers to the new
intel_skl_int3472_tps68470.ko to help with probe ordering issues
without causing these modules to get loaded on boards which only
use the int3472_discrete platform driver.

While at it also rename the .c and .h files to remove the
cumbersome intel_skl_int3472_ prefix.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-8-hdegoede@redhat.com

The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.

To work around cases where this info is not present in the firmware tables,
which is often the case on x86/ACPI devices, both frameworks allow the
provider-driver to attach info about consumers to the provider-device
during probe/registration of the provider device.

The TI TPS68470 PMIC is used x86/ACPI devices with the consumer-info
missing from the ACPI tables. Thus the tps68470-clk and tps68470-regulator
drivers must provide the consumer-info at probe time.

Define tps68470_clk_platform_data and tps68470_regulator_platform_data
structs to allow the x86 platform code to pass the necessary consumer info
to these drivers.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-5-hdegoede@redhat.com

Change i2c_acpi_new_device() into i2c_acpi_new_device_by_fwnode() and
add a static inline wrapper providing the old i2c_acpi_new_device()
behavior.

This is necessary because in some cases we may only have access
to the fwnode / acpi_device and not to the matching physical-node
struct device *.

Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-4-hdegoede@redhat.com

The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.

To work around cases where this info is not present in the firmware tables,
which is often the case on x86/ACPI devices, both frameworks allow the
provider-driver to attach info about consumers to the clks/regulators
when registering these.

This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.

To ensure the correct probe-ordering the ACPI core has code to defer the
enumeration of consumers affected by this until the providers are ready.

Call the new acpi_dev_ready_for_enumeration() helper to avoid
enumerating / instantiating i2c-clients too early.

Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-3-hdegoede@redhat.com

The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.

To work around cases where this info is not present in the firmware tables,
which is often the case on x86/ACPI devices, both frameworks allow the
provider-driver to attach info about consumers to the clks/regulators
when registering these.

This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.

One case where we hit this issue is camera sensors such as e.g. the OV8865
sensor found on the Microsoft Surface Go. The sensor uses clks, regulators
and GPIOs provided by a TPS68470 PMIC which is described in an INT3472
ACPI device. There is special platform code handling this and setting
platform_data with the necessary consumer info on the MFD cells
instantiated for the PMIC under: drivers/platform/x86/intel/int3472.

For this to work properly the ov8865 driver must not bind to the I2C-client
for the OV8865 sensor until after the TPS68470 PMIC gpio, regulator and
clk MFD cells have all been fully setup.

The OV8865 on the Microsoft Surface Go is just one example, all X86
devices using the Intel IPU3 camera block found on recent Intel SoCs
have similar issues where there is an INT3472 HID ACPI-device, which
describes the clks and regulators, and the driver for this INT3472 device
must be fully initialized before the sensor driver (any sensor driver)
binds for things to work properly.

On these devices the ACPI nodes describing the sensors all have a _DEP
dependency on the matching INT3472 ACPI device (there is one per sensor).

This allows solving the probe-ordering problem by delaying the enumeration
(instantiation of the I2C-client in the ov8865 example) of ACPI-devices
which have a _DEP dependency on an INT3472 device.

The new acpi_dev_ready_for_enumeration() helper used for this is also
exported because for devices, which have the enumeration_by_parent flag
set, the parent-driver will do its own scan of child ACPI devices and
it will try to enumerate those during its probe(). Code doing this such
as e.g. the i2c-core-acpi.c code must call this new helper to ensure
that it too delays the enumeration until all the _DEP dependencies are
met on devices which have the new honor_deps flag set.

Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-2-hdegoede@redhat.com

Since 89a6a5e5

("regulator: add property parsing and callbacks to set protection limits")
which introduced a warning:

Documentation/driver-api/regulator:166: ./include/linux/regulator/driver.h:96: WARNING: Unexpected indentation.
Documentation/driver-api/regulator:166: ./include/linux/regulator/driver.h:98: WARNING: Block quote ends without a blank line; unexpected unindent.

Let's fix them.

Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20211207123230.2262047-1-siyanteng@loongson.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

According to the description and the various uses of this property it is
meant to be an array of unsigned 32-bit values, so fixup the type to
match that.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211206153726.227464-1-thierry.reding@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

One of the examples in the bindings has an interrupts property and the
Linux kernel driver has support for requesting an interrupt as well. It
looks like the absence from the bindings was just an oversight. Add the
property to make sure the examples can be validated.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211206153432.226963-1-thierry.reding@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add the rpmh regulators found in PM8450 PMIC

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211201072515.3968843-3-vkoul@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

Add compatible string for PM8450 used in SM8450 boards.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211201072515.3968843-2-vkoul@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

Add the configuration for the DA9141 and DA9142 regulators.
Also tidy the table, cleaning away superfluous information.

Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/9293e3ae4ff8776704257085df65516b81209b87.1638223185.git.Adam.Ward.opensource@diasemi.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Clean away information from a test that was included accidentally

Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/530a626cee6bc12ff5b4ab16319ac7a1fac6e306.1638223185.git.Adam.Ward.opensource@diasemi.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add the DA9141 and DA9142 regulators device recognition data and
operational parameters.

Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/5f5b9b02f07578cd36c6bc266349a56efc9b08d1.1638223185.git.Adam.Ward.opensource@diasemi.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Prevent changing current limit when enabled as a precaution against
possibile instability due to tight integration with switching cycle

Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/52ee682476004a1736c1e0293358987319c1c415.1638223185.git.Adam.Ward.opensource@diasemi.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add support for PMG1110 regulators.

Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Link: https://lore.kernel.org/r/1637668167-31325-3-git-send-email-quic_c_skakit@quicinc.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add compatible string for pmg1110 pmic.

Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Link: https://lore.kernel.org/r/1637668167-31325-2-git-send-email-quic_c_skakit@quicinc.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The PM8226 PMIC is very often seen on
MSM8x26 boards.

Suggested-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211123181119.2897-1-dominikkobinski314@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Suggested-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Link: https://lore.kernel.org/r/20211123180816.2835-1-dominikkobinski314@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Function rohm_regulator_set_voltage_sel_restricted() and
rohm_regulator_set_dvs_levels() had inlined dummy implementations for
cases when the real implementation was not configured in.

All of the drivers who issue the call to these functions do SELECT the
real implementation from the Kconfig. There should be no cases where the
real implementation was not selected by the drivers using these
functions - such a situation is likely to be an error which deserves to be
noticed at compile-time.

These dummies could in theory be used for compile-testing the drivers
only (without the generic rohm regulator pieces). However, for such
compile testing we should manually drop the selection from KConfig - and
I guess that if it does not work out-of-the-box, then it is not going to
happen. Especially when there should be no reason to omit
compile-testing the generic rohm_regulator part.

Crash test dummies.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/YZ3UXXrk/Efe7Scj@fedora


Signed-off-by: Mark Brown <broonie@kernel.org>

Provide a generic map_event helper for regulators which have a notification
IRQ with single, well defined purpose. Eg, IRQ always indicates exactly one
event for exactly one regulator device. For such IRQs the mapping is
trivial.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/603b7ed1938013a00371c1e7ccc63dfb16982b87.1637736436.git.matti.vaittinen@fi.rohmeurope.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Help drivers avoid storing both supported notification and supported error
flags by supporting conversion from regulator error to notification.
This may help saving some bytes.

Add helper for finding the regulator notification corresponding to a
regulator error.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/eb1755ac0569ff07ffa466cf8912c6fd50e7c7c6.1637736436.git.matti.vaittinen@fi.rohmeurope.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The irq_flags from the regulator IRQ helper description struct was never
used. The IRQ flags are passed as parameters to helper registration
instead.

Remove the unnecessary struct field.

Fixes: 7111c6d1

 ("regulator: IRQ based event/error notification helpers")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/5f6371e178453fa2b165da50452f7db4e986debb.1637736436.git.matti.vaittinen@fi.rohmeurope.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The function rohm_regulator_set_voltage_sel_restricted() has a stub
implementation. Linux-next testing spot following:

include/linux/mfd/rohm-generic.h:93:12: error:
'rohm_regulator_set_voltage_sel_restricted' defined but not used

Fix this by inlining the stub.

Fixes: 8b6e8855

 ("regulator: rohm-regulator: add helper for restricted voltage setting")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/YZzEP3S7U15bTDAI@fedora


Signed-off-by: Mark Brown <broonie@kernel.org>

The documentation for limits used at protection level setting
did not mention the units. Fix the units in documentation to
match values passed in from device-tree (uV, uA, Kelvin) to
avoid confusion.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/111114aca991e41e49a32f89b74e95285f07c1e3.1637233864.git.matti.vaittinen@fi.rohmeurope.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Use common restricted voltage setting instead of implementing own.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/5a0ee14852802690241568a29ed19ff9550b0b08.1637233864.git.matti.vaittinen@fi.rohmeurope.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Few ROHM PMICs have regulators where voltage setting can be done only
when regulator is disabled. Add helper for those PMICs.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/6f51871e9fea611d133b5dd2560f4a7ee1ede9cd.1637233864.git.matti.vaittinen@fi.rohmeurope.com


Signed-off-by: Mark Brown <broonie@kernel.org>

When an i2c remove callback fails, the i2c core emits a generic error
message and still removes the device. Apart from the message there the
return value isn't further used.

So don't return an error code after having already emitted a driver
specific warning about the problem to prevent two messages about the
same issue.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211116110951.1213566-1-u.kleine-koenig@pengutronix.de


Signed-off-by: Mark Brown <broonie@kernel.org>