- May 15, 2020
-
-
Stephan Gerhold authored
apq8016-sbc.dtsi is the only remaining device which takes up 4 files since it has its pinctrl split into separate files. Actually this does not really make the device tree easier to read (just harder to find nodes). For db820c the files were merged in commit 88264f1f ("arm64: dts: qcom: db820c: Remove pin specific files"). Do the same for apq8016-sbc (db410c) and move the pinctrl definitions into apq8016-sbc.dtsi. Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20200514112754.148919-3-stephan@gerhold.net Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org>
-
Stephan Gerhold authored
In msm8916.dtsi the GPU OPP table is defined under the root node, whereas in msm8996.dtsi/sdm845.dtsi it is a subnode of the gpu device (which makes it easier to find). Move it to the gpu device node to make this consistent. Signed-off-by:
-
Stephan Gerhold authored
Many nodes in the MSM8916 device trees use '_' in node names (especially pinctrl), even though (seemingly) '-' is preferred now. Make this more consistent by replacing '_' with '-' where possible. Similar naming is used for pinctrl in newer device trees (e.g. sdm845.dtsi). Signed-off-by:
-
Bjorn Andersson authored
On some device the reset line for the UFS memory needs to be tickled in order for UFS to initialize properly, add this to the ufs_mem_hc node. Reviewed-by:
Robert Foss <robert.foss@linaro.org> Reviewed-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Bjorn Andersson authored
Specify regulators and enable the &wifi node. The firmware uses the 8 bit version of the host capability message, so specify this quirk. Reviewed-by:
-
Michael Srba authored
This patch wires up display support on Samsung Galaxy A3 2015. Signed-off-by:
Michael Srba <michael.srba@seznam.cz> Link: https://lore.kernel.org/r/20200514170129.10902-1-michael.srba@seznam.cz Signed-off-by:
-
- May 14, 2020
-
-
Bjorn Andersson authored
It's uncertain where the "vreg_s8a_l3a_input" comes from, but the supply for VDD_L3_L11 on PM8994 should be VREG_S3A_1P3, so correct this - and drop the vreg_s8a_l3a_input. Reviewed-by:
-
Bjorn Andersson authored
The PMI8994 provides 3 SPMS regulators and one boost/bypass regulator. Define s1 and the boot/bypass and update pm8994 to appropriately describe the supply from PMI8994. Reviewed-by:
-
Michael Srba authored
On some msm8916 devices, attempts at initializing coresight cause the boot to fail. This was fixed by disabling the coresight-related nodes in the board dts files. However, a cleaner approach was chosen for fixing the same issue on msm8998: disabling coresight by default, and enabling it in board dts files where desired. This patch implements the same solution for msm8916, removes now redundant overwrites in board specific dts files and and enables coresight in db410c's board dts in order to keep the current behavior. Fixes: b1fcc570 ("arm64: dts: qcom: msm8916: Add CTI options") Signed-off-by:
Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Link: https://lore.kernel.org/r/20200513184735.30104-1-michael.srba@seznam.cz Signed-off-by:
-
- May 13, 2020
-
-
Douglas Anderson authored
The example in the bindings and all the current users (except sc7180) have "no-map". I'm pretty sure we need it on sc7180 too. Add it. Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Fixes: e0abc5eb ("arm64: dts: qcom: sc7180: Add cmd_db reserved area") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200424085121.1.I9d1e84d30f488cdb5a957f582abaecd2c0b24d70@changeid Signed-off-by:
-
Stephan Gerhold authored
A5U uses a Melfas MMS345L touchscreen that is connected to blsp_i2c5. Add it to the device tree. Signed-off-by:
-
Stephan Gerhold authored
A3U and A5U both use an extra touchscreen LDO regulator that provides 3.3V for the touch screen controller. Add it as fixed regulator to the common include. Cc: Michael Srba <Michael.Srba@seznam.cz> Signed-off-by:
-
Stephan Gerhold authored
MSM8916 has another I2C QUP controller that can be enabled on GPIO 18 and 19. Add blsp_i2c5 to msm8916.dtsi and disable it by default. Reviewed-by:
-
Stephan Gerhold authored
MSM8916 has another I2C QUP controller that can be enabled on GPIO 2 and 3. Add blsp_i2c1 to msm8916.dtsi and disable it by default. Reviewed-by:
-
Sai Prakash Ranjan authored
Now that deep idle states are properly supported on SC7180, we need to add "coresight-loses-context-with-cpu" property to avoid failure of trace session because of losing context on entering deep idle states. Reviewed-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Link: https://lore.kernel.org/r/20200424111644.27970-1-saiprakash.ranjan@codeaurora.org Signed-off-by:
-
- May 12, 2020
-
-
Douglas Anderson authored
We don't have the HPD line hooked up to the bridge chip. Add it as suggested in the patch ("dt-bindings: drm/bridge: ti-sn65dsi86: Document no-hpd"). NOTE: this patch isn't expected to have any effect but just keeps us cleaner for the future. Currently the driver in Linux just assumes that nobody has HPD hooked up. This change allows us to later implement HPD support in the driver without messing up sdm845-cheza. Signed-off-by: -
Loic Poulain authored
Add CCI controller node, which can be used to communicate with camera sensors (I2C subset). MSM8996 CCI offers two masters, i2c-bus@0 and i2c-bus@1. Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/1587470425-13726-2-git-send-email-loic.poulain@linaro.org Signed-off-by:
-
Loic Poulain authored
Each IRQ_TYPE_NONE interrupt causes a warning at boot. Fix that by defining an appropriate type. Fixes: e0531312 ("arm64: dts: qcom: msm8996: Add CAMSS support") Signed-off-by:
-
Sibi Sankar authored
Add TCSR node and update MSS node to support MSA based Modem boot on SC7180 SoCs. Reviewed-by:
Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200421143228.8981-8-sibis@codeaurora.org Signed-off-by:
-
Sibi Sankar authored
This patch adds Q6V5 MSS PAS remoteproc node for SC7180 SoCs. Reviewed-by:
-
Sibi Sankar authored
Add missing regions and remove unused regions from the reserved memory map, as described in version 5. Tested-by:
Evan Green <evgreen@chromium.org> Signed-off-by:
-
- May 07, 2020
-
-
Sibi Sankar authored
Add missing SoC compatible to SDM845 MTP board file. Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by:
-
- May 05, 2020
-
-
Alex Elder authored
Add an "iommus" property to the IPA node in "sdm845.dtsi". It is required because there are two regions of memory the IPA accesses through an SMMU. The next few patches define and map those regions. Signed-off-by:
Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/20200504181350.22822-1-elder@linaro.org Signed-off-by:
-
- Apr 23, 2020
-
-
Mike Leach authored
Adds system and CPU bound CTI definitions for Qualcom msm8916 platform (Dragonboard DB410C). System CTIs 2-11 are omitted as no information available at present. Signed-off-by:
Mike Leach <mike.leach@linaro.org> Reviewed-by:
Mathieu Poirier <mathieu.poirier@linaro.org> Acked-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20200415201230.15766-1-mike.leach@linaro.org Signed-off-by:
-
Alexey Minnekhanov authored
This adds the initial device tree support for Xiaomi Redmi Note 7 (codename lavender) phone. It is based on SDM660 SoC. Currently it can be booted into initrd with a shell over UART and you can also get kernel boot logs from a pstore-ramoops. Signed-off-by:
Alexey Minnekhanov <alexey.min@gmail.com> Link: https://lore.kernel.org/r/20200417012630.222352-4-alexey.min@gmail.com Signed-off-by:
-
Craig Tatlor authored
Initial device tree support for Qualcomm SDM660 SoC. SDM660 is based off MSM8998 and uses some of its drivers. SDM630/636 are based off SDM660 SoC and they are pin and software compatible. The device tree is based on the CAF 4.4 kernel tree. Features: * CPU nodes * Timer nodes * Interrupt controller * Global Clock Controller * Top Level Mode Multiplexer (pin controller) * UART node This is inspired by and based on the work of Craig Tatlor in https://patchwork.kernel.org/patch/10563667/ Signed-off-by:
Craig Tatlor <ctatlor97@gmail.com> Signed-off-by:
-
Alexey Minnekhanov authored
Add a SoC strings for the Qualcomm SDM630 and SDM660 SoCs. Also document the new xiaomi,lavender compatible used in a device tree binding. Signed-off-by:
-
- Apr 21, 2020
-
-
Bjorn Andersson authored
The pdc node suffers from both too narrow compatible and insufficient cells in the reg, fix these. Fixes: 60378f1a ("arm64: dts: qcom: sm8250: Add sm8250 dts file") Tested-by:
-
Bryan O'Donoghue authored
Add nodes for the UFS controller and PHY, and enable these for the MTP with relevant supplies specified. Tested-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lore.kernel.org/r/20200415061430.740854-3-bjorn.andersson@linaro.org Signed-off-by:
-
Bryan O'Donoghue authored
Add RPMh controlled regulators for the three PMICs and specify voltage ranges and mode for relevant regulators. Tested-by:
-
Bjorn Andersson authored
Tested-by:
-
Sai Prakash Ranjan authored
Add coresight components found on Qualcomm SC7180 SoC. Signed-off-by:
-
Jonathan Marek authored
This was mistakenly copied from the downstream dts, however the upstream driver works differently. I only tested this with the pm8150_gpios node (used with volume button), but the 2 others should be the same. Fixes: e92b61c8 ("arm64: dts: qcom: pm8150l: Add base dts file") Fixes: 229d5bca ("arm64: dts: qcom: pm8150b: Add base dts file") Fixes: 5101f22a ("arm64: dts: qcom: pm8150: Add base dts file") Reviewed-by:
Jonathan Marek <jonathan@marek.ca> Link: https://lore.kernel.org/r/20200420153543.14512-1-jonathan@marek.ca Signed-off-by:
-
- Apr 15, 2020
-
-
Sandeep Maheswaram authored
Overriding the QUSB2 V2 Phy tuning parameters for SC7180 IDP device. Signed-off-by:
Sandeep Maheswaram <sanm@codeaurora.org> Reviewed-by:
-
Sandeep Maheswaram authored
Use generic QUSB2 V2 Phy configuration for SC7180. Signed-off-by:
-
Sandeep Maheswaram authored
Use generic QUSB2 V2 Phy configuration for sdm845. Signed-off-by:
-
- Apr 14, 2020
-
-
Maulik Shah authored
Add device bindings for cpuidle states for cpu devices. Cc: devicetree@vger.kernel.orgi Signed-off-by:
Maulik Shah <mkshah@codeaurora.org> Reviewed-by:
Srinivas Rao L <lsrao@codeaurora.org> Reviewed-by:
-
Sivaprakash Murugesan authored
This patch re-arranges ipq8074 device nodes based on node address followed by node names followed by node labels. Suggested-by:
Sivaprakash Murugesan <sivaprak@codeaurora.org> Link: https://lore.kernel.org/r/1586572830-22727-1-git-send-email-sivaprak@codeaurora.org Signed-off-by:
-
Matthias Kaehlcke authored
Add the interconnect path configuration for the venus video codec of the SC7180. Signed-off-by:
-
Rajeshwari authored
Changed polling-delay and polling-delay-passive to zero to disable polling mode of the framework as interrupts for tsens are already configured. Signed-off-by:
Rajeshwari <rkambl@codeaurora.org> Reviewed-by:
-
