Now that we're hoping to have resolved all of the problems with
video.use_native_backlight=1, make that the default at last.

Link: http://marc.info/?l=linux-acpi&m=139716088401106&w=2


Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Acer Aspire V5-171
References: https://bugzilla.redhat.com/show_bug.cgi?id=983342



Acer Aspire V5-471G
Lenovo Yoga 2 11
Reported-and-tested-by: Vincent Gerris <vgerris@gmail.com>

HP EliteBook 8470p
References: https://bugzilla.redhat.com/show_bug.cgi?id=1093120



Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Like all of the other *30 ThinkPad models, the W530 has a broken acpi-video
backlight control. Note in order for this to actually fix things on the
ThinkPad W530 the commit titled:
"nouveau: Don't check acpi_video_backlight_support() before registering backlight"
is also needed.

References: https://bugzilla.redhat.com/show_bug.cgi?id=1093171


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When video.use_native_backlight=1 and non intel gfx are in use, the raw
backlight device of the gfx driver will show up after acpi-video has done its
acpi_video_verify_backlight_support() check.

This causes video.use_native_backlight=1 to not have the desired result.

This patch fixes this by adding a backlight notifier and when a raw
backlight is registered or unregistered re-doing the
acpi_video_verify_backlight_support() check.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Some firmware drivers, ie acpi-video want to get themselves out of the
way (in some cases) when their also is a raw backlight device available.

Due to module loading ordering being unknown, acpi-video cannot be certain
that the backlight_device_registered(BACKLIGHT_RAW) it does for this is
the final verdict wrt there being a BACKLIGHT_RAW device.

By adding notification acpi-video can listen for backlight devices showing
up after it has loaded, and unregister its backlight device if desired.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

acpi_video_backlight_support() is supposed to be called by other (vendor
specific) firmware backlight controls, not by native / raw backlight controls
like nv_backlight.

Userspace will normally prefer firmware interfaces over raw interfaces, so
if acpi_video backlight support is present it will use that even if
nv_backlight is registered as well.

Except when video.use_native_backlight is present on the kernel cmdline
(or enabled through a dmi based quirk). As the name indicates the goal here
is to make only the raw interface available to userspace so that it will use
that (it only does this when it sees a win8 compliant bios).

This is done by:
1) Not registering any acpi_video# backlight devices; and
2) Making acpi_video_backlight_support() return true so that other firmware
drivers, ie acer_wmi, thinkpad_acpi, dell_laptop, etc. Don't register their
own vender specific interfaces.

Currently nouveau breaks this setup, as when acpi_video_backlight_support()
returns true, it does not register itself, resulting in no backlight control
at all.

This is esp. going to be a problem with 3.16 which will default to
video.use_native_backlight=1, and thus nouveau based laptops with a win8 bios
will get no backlight control at all.

This also likely explains why the previous attempt to make
video.use_native_backlight=1 the default was not a success, as without this
patch having a default of video.use_native_backlight=1 will cause regressions.

Note this effectively reverts commit 5bead799 (drm/nouveau: don't
expose backlight control when available through ACPI).

References: https://bugzilla.redhat.com/show_bug.cgi?id=1093171


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The Aspire 5741 has broken acpi-video backlight control, so add it to the
quirk table.

References: https://bugzilla.redhat.com/show_bug.cgi?id=1012674


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Switch from acpi_video_unregister(), to acpi_video_unregister_backlight(),
so that the hotkeys handler registered by acpi-video stays in place.

Since there are no mappings for the atkbd raw codes for the brightness
keys used by newer Acer models in /lib/udev/hwdb.d/60-keyboard.hwdb, and
since we map the wmi events with a code of KE_IGNORE, we rely on acpi-video
to do the hotkey handling for us.

For laptops such as the Acer Aspire 5750 which uses intel gfx this works
despite us calling acpi_video_unregister() because the following happens:

 1) acpi-video module gets loaded (as it is a dependency of acer-wmi and i915)
 2) acpi-video does NOT call acpi_video_register()
 3) acer-wmi loads (assume it loads before i915), calls
    acpi_video_dmi_promote_vendor(); which sets
    ACPI_VIDEO_BACKLIGHT_DMI_VENDOR
 4) calls acpi_video_unregister -> not registered, nop
 5) i915 loads, calls acpi_video_register
 6) acpi_video_register registers the acpi_notifier for the hotkeys,
    does NOT register a backlight device because of
    ACPI_VIDEO_BACKLIGHT_DMI_VENDOR

But on the Acer Aspire 5750G, which uses nvidia graphics the following happens:
 1) acpi-video module gets loaded (as it is a dependency of acer-wmi)
 2) acpi-video calls acpi_video_register()
 3) acpi_video_register registers the acpi_notifier for the hotkeys,
    and a backlight device
 4) acer-wmi loads, calls acpi_video_dmi_promote_vendor()
 5) calls acpi_video_unregister, this unregisters BOTH the acpi_notifier for
    the hotkeys AND the backlight device

And we end up without any handler for the brightness hotkeys. This patch fixes
this by switching over to acpi_video_unregister_backlight() which keeps the
hotkey handler in place.

References: https://bugzilla.kernel.org/show_bug.cgi?id=35622


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add an acpi_video_unregister_backlight function, which only unregisters
the backlight device, and leaves the acpi_notifier in place. Some acpi_vendor
driver need this as they don't want the acpi_video# backlight device, but do
need the acpi-video driver for hotkey handling.

Chances are that this new acpi_video_unregister_backlight() is actually
what existing acpi_vendor drivers have wanted all along. Currently acpi_vendor
drivers which want to disable the acpi_video# backlight device, make 2 calls:

acpi_video_dmi_promote_vendor();
acpi_video_unregister();

The intention here is to make things independent of when acpi_video_register()
gets called. As acpi_video_register() will get called on acpi-video load time
on non intel gfx machines, while it gets called on i915 load time on intel
gfx machines.

This leads to the following 2 interesting scenarios:

 a) intel gfx:
  1) acpi-video module gets loaded (as it is a dependency of acpi_vendor
     and i915)
  2) acpi-video does NOT call acpi_video_register()
  3) acpi_vendor loads (lets assume it loads before i915), calls
     acpi_video_dmi_promote_vendor(); which sets
     ACPI_VIDEO_BACKLIGHT_DMI_VENDOR
  4) calls acpi_video_unregister -> not registered, nop
  5) i915 loads, calls acpi_video_register
  6) acpi_video_register registers the acpi_notifier for the hotkeys,
     does NOT register a backlight device because of
     ACPI_VIDEO_BACKLIGHT_DMI_VENDOR

 b) non intel gfx
  1) acpi-video module gets loaded (as it is a dependency acpi_vendor)
  2) acpi-video calls acpi_video_register()
  3) acpi_video_register registers the acpi_notifier for the hotkeys,
     and a backlight device
  4) acpi_vendor loads, calls acpi_video_dmi_promote_vendor()
  5) calls acpi_video_unregister, this unregisters BOTH the acpi_notifier
     for the hotkeys AND the backlight device

So here we have possibly the same acpi_vendor module, making the same calls,
but with different results, in one cases acpi-video does handle hotkeys,
in the other it does not.

Note that the a) scenario turns into b) if we assume the i915 module loads
before the vendor_acpi module, so we also have different behavior depending
on module loading order!

So as said I believe that quite a few existing acpi_vendor modules really
always want the behavior of a), hence this patch adds a new
acpi_video_unregister_backlight() which gives the behavior of a) independent
of module loading order.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Seems it helps some users, but causes issues for other users:
https://bugzilla.redhat.com/show_bug.cgi?id=1089545

So lets drop it for now until we've figured out a better fix.

Fixes: 43d94902 (ACPI / video: Add use_native_backlight quirks for more systems)
References: https://bugzilla.redhat.com/show_bug.cgi?id=1089545


Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

If we're not going to be registering any backlight devices then
acpi_video_resume is always nop, so don't register it in that case.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The DMI tag used to identify Dell Inspiron 7520 should be product name
instead of product version.

Fixes: 0e9f81d3

 (ACPI / video: Add systems that should favour native backlight interface)
Reported-and-tested-by: Téo Mazars <teomazars@gmail.com>
References: https://bugzilla.redhat.com/show_bug.cgi?id=909552


Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

acpi-video is unique in that it not only generates brightness up/down
keypresses, but also (sometimes) actively changes the brightness itself.

This presents an inconsistent kernel interface to userspace, basically there
are 2 different scenarios, depending on the laptop model:

 1) On some laptops a brightness up/down keypress means: show a brightness osd
 with the current brightness, iow it is a brightness has changed notification.

 2) Where as on (a lot of) other laptops it means a brightness up/down key was
 pressed, deal with it.

Most of the desktop environments interpret any press as in scenario 2, and
change the brightness up / down as a response to the key events, causing it
to be changed twice, once by acpi-video and once by the DE.

With the new default for video.use_native_backlight we will be moving even
more laptops over to behaving as in scenario 2. Making the remaining laptops
even more of a weird exception. Also note that it is hard to detect scenario
1 properly in userspace, and AFAIK none of the DE-s deals with it.

Therefor this commit changes the default of brightness_switch_enabled to 0
making its behavior consistent with all the other backlight drivers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

ThinkPad T430: extend the T430s entry to also cover the T430 (note we also
have another entry for T430's with a different DMI_PRODUCT_VERSION).

ThinkPad T430
Reported-and-tested-by: edm <fuffi.il.fuffo@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231



Thinkpad T530
Reported-and-tested-by: Balint Szigeti <balint.szgt@gmail.com>
References: https://bugzilla.redhat.com/show_bug.cgi?id=1089545



Acer Aspire 5742G
Reported-and-tested-by: AnAkkk <anakin.cs@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=35622



Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull file locking change from Jeff Layton:
 "Only an email address change to the MAINTAINERS file"

* tag 'locks-v3.15-3' of git://git.samba.org/jlayton/linux:
  MAINTAINERS: email address change for Jeff Layton

Pull arm64 fixes from Catalin Marinas:
 "These are mostly arm64 fixes with an additional arm(64) platform fix
  for the initialisation of vexpress clocks (the latter only affecting
  arm64; the arch/arm64 code is SoC agnostic and does not rely on early
  SoC-specific calls)

   - vexpress platform clocks initialisation moved earlier following the
     arm64 move of of_clk_init() call in a previous commit
   - Default DMA ops changed to non-coherent to preserve compatibility
     with 32-bit ARM DT files.  The "dma-coherent" property can be used
     to explicitly mark a device coherent.  The Applied Micro DT file
     has been updated to avoid DMA cache maintenance for the X-Gene SATA
     controller (the only arm64 related driver with such assumption in
     -rc mainline)
   - Fixmap correction for earlyprintk
   - kern_addr_valid() fix for huge pages"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git...

Pull SCSI fixes from James Bottomley:
 "This is two patches both fixing bugs in drivers (virtio-scsi and
  mpt2sas) causing an oops in certain circumstances"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] virtio-scsi: Skip setting affinity on uninitialized vq
  [SCSI] mpt2sas: Don't disable device twice at suspend.

Following arm64 commit bc3ee18a

 (arm64: init: Move of_clk_init to
time_init()), vexpress_osc_of_setup() is called via of_clk_init() long
before initcalls are issued. Initialising the vexpress oscillators
requires the vespress sysregs to be already initialised, so this patch
adds an explicit call to vexpress_sysreg_of_early_init() in vexpress
oscillator setup function.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>

Since the default DMA ops for arm64 are non-coherent, mark the X-Gene
controller explicitly as dma-coherent to avoid additional cache
maintenance.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Loc Ho <lho@apm.com>

Recently, the default DMA ops have been changed to non-coherent for
alignment with 32-bit ARM platforms (and DT files). This patch adds bus
notifiers to be able to set the coherent DMA ops (with no cache
maintenance) for devices explicitly marked as coherent via the
"dma-coherent" DT property.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Currently arm64 dma_ops is by default made coherent which makes it
opposite in default policy from arm.

Make default dma_ops to be noncoherent (same as arm), as currently there
aren't any dma-capable drivers which assumes coherent ops

Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Commit d57c33c5 (add generic fixmap.h) added (among other
similar things) set_fixmap_io to deal with early ioremap of devices.

More recently, commit bf4b558e

 (arm64: add early_ioremap support)
converted the arm64 earlyprintk to use set_fixmap_io. A side effect of
this conversion is that my virtual machines have stopped booting when
I pass "earlyprintk=uart8250-8bit,0x3f8" to the guest kernel.

Turns out that the new earlyprintk code doesn't care at all about
sub-page offsets, and just assumes that the earlyprintk device will
be page-aligned. Obviously, that doesn't play well with the above example.

Further investigation shows that set_fixmap_io uses __set_fixmap instead
of __set_fixmap_offset. A fix is to introduce a set_fixmap_offset_io that
uses the latter, and to remove the superflous call to fix_to_virt
(which only returns the value that set_fixmap_io has already given us).

With this applied, my VMs are back in business. Tested on a Cortex-A57
platform with kvmtool as platform emulation.

Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Salter <msalter@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Fix for the arm64 kern_addr_valid() function to recognize
virtual addresses in the kernel logical memory map.  The
function fails as written because it does not check whether
the addresses in that region are mapped at the pmd level to
2MB or 512MB pages, continues the page table walk to the
pte level, and issues a garbage value to pfn_valid().

Tested on 4K-page and 64K-page kernels.

Signed-off-by: Dave Anderson <anderson@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull irq fixes from Thomas Gleixner:
 "This udpate delivers:

   - A fix for dynamic interrupt allocation on x86 which is required to
     exclude the GSI interrupts from the dynamic allocatable range.

     This was detected with the newfangled tablet SoCs which have GPIOs
     and therefor allocate a range of interrupts.  The MSI allocations
     already excluded the GSI range, so we never noticed before.

   - The last missing set_irq_affinity() repair, which was delayed due
     to testing issues

   - A few bug fixes for the armada SoC interrupt controller

   - A memory allocation fix for the TI crossbar interrupt controller

   - A trivial kernel-doc warning fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: irq-crossbar: Not allocating enough memory
  irqchip: armanda: Sanitize set_irq_affinity()
  genirq: x86: Ensure that dynamic irq allocation does not con...

Pull timer fixes from Thomas Gleixner:
 "This update brings along:

   - Two fixes for long standing bugs in the hrtimer code, one which
     prevents remote enqueuing and the other preventing arbitrary delays
     after a interrupt hang was detected

   - A fix in the timer wheel which prevents math overflow

   - A fix for a long standing issue with the architected ARM timer
     related to the C3STOP mechanism.

   - A trivial compile fix for nspire SoC clocksource"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timer: Prevent overflow in apply_slack
  hrtimer: Prevent remote enqueue of leftmost timers
  hrtimer: Prevent all reprogramming if hang detected
  clocksource: nspire: Fix compiler warning
  clocksource: arch_arm_timer: Fix age-old arch timer C3STOP detection issue

Merge tag 'trace-fixes-v3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace



Pull tracing fix from Steven Rostedt:
 "This is a small fix where the trigger code used the wrong
  rcu_dereference().  It required rcu_dereference_sched() instead of the
  normal rcu_dereference().  It produces a nasty RCU lockdep splat due
  to the incorrect rcu notation"

Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>

* tag 'trace-fixes-v3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Use rcu_dereference_sched() for trace event triggers

As trace event triggers are now part of the mainline kernel, I added
my trace event trigger tests to my test suite I run on all my kernels.
Now these tests get run under different config options, and one of
those options is CONFIG_PROVE_RCU, which checks under lockdep that
the rcu locking primitives are being used correctly. This triggered
the following splat:

===============================
[ INFO: suspicious RCU usage. ]
3.15.0-rc2-test+ #11 Not tainted
-------------------------------
kernel/trace/trace_events_trigger.c:80 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 0
4 locks held by swapper/1/0:
 #0:  ((&(&j_cdbs->work)->timer)){..-...}, at: [<ffffffff8104d2cc>] call_timer_fn+0x5/0x1be
 #1:  (&(&pool->lock)->rlock){-.-...}, at: [<ffffffff81059856>] __queue_work+0x140/0x283
 #2:  (&p->pi_lock){-.-.-.}, at: [<ffffffff8106e961>] try_to_wake_up+0x2e/0x1e8
 #3:  (&rq->lock){-.-.-.}, at: [<ffffffff8106ead3>] try_to_wake_up+0x1a0/0x1e8

stack backtrace:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.15.0-rc2-test+ #11
Hardware name:                  /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006
 0000000000000001 ffff88007e083b98 ffffffff819f53a5 0000000000000006
 ffff88007b0942c0 ffff88007e083bc8 ffffffff81081307 ffff88007ad96d20
 0000000000000000 ffff88007af2d840 ffff88007b2e701c ffff88007e083c18
Call Trace:
 <IRQ>  [<ffffffff819f53a5>] dump_stack+0x4f/0x7c
 [<ffffffff81081307>] lockdep_rcu_suspicious+0x107/0x110
 [<ffffffff810ee51c>] event_triggers_call+0x99/0x108
 [<ffffffff810e8174>] ftrace_event_buffer_commit+0x42/0xa4
 [<ffffffff8106aadc>] ftrace_raw_event_sched_wakeup_template+0x71/0x7c
 [<ffffffff8106bcbf>] ttwu_do_wakeup+0x7f/0xff
 [<ffffffff8106bd9b>] ttwu_do_activate.constprop.126+0x5c/0x61
 [<ffffffff8106eadf>] try_to_wake_up+0x1ac/0x1e8
 [<ffffffff8106eb77>] wake_up_process+0x36/0x3b
 [<ffffffff810575cc>] wake_up_worker+0x24/0x26
 [<ffffffff810578bc>] insert_work+0x5c/0x65
 [<ffffffff81059982>] __queue_work+0x26c/0x283
 [<ffffffff81059999>] ? __queue_work+0x283/0x283
 [<ffffffff810599b7>] delayed_work_timer_fn+0x1e/0x20
 [<ffffffff8104d3a6>] call_timer_fn+0xdf/0x1be^M
 [<ffffffff8104d2cc>] ? call_timer_fn+0x5/0x1be
 [<ffffffff81059999>] ? __queue_work+0x283/0x283
 [<ffffffff8104d823>] run_timer_softirq+0x1a4/0x22f^M
 [<ffffffff8104696d>] __do_softirq+0x17b/0x31b^M
 [<ffffffff81046d03>] irq_exit+0x42/0x97
 [<ffffffff81a08db6>] smp_apic_timer_interrupt+0x37/0x44
 [<ffffffff81a07a2f>] apic_timer_interrupt+0x6f/0x80
 <EOI>  [<ffffffff8100a5d8>] ? default_idle+0x21/0x32
 [<ffffffff8100a5d6>] ? default_idle+0x1f/0x32
 [<ffffffff8100ac10>] arch_cpu_idle+0xf/0x11
 [<ffffffff8107b3a4>] cpu_startup_entry+0x1a3/0x213
 [<ffffffff8102a23c>] start_secondary+0x212/0x219

The cause is that the triggers are protected by rcu_read_lock_sched() but
the data is dereferenced with rcu_dereference() which expects it to
be protected with rcu_read_lock(). The proper reference should be
rcu_dereference_sched().

Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Pull ACPI and power management fixes from Rafael Wysocki:
 "A bunch of regression fixes this time.  They fix two regressions in
  the PNP subsystem, one in the ACPI processor driver and one in the
  ACPI EC driver, four cpufreq driver regressions and an unrelated bug
  in one of the drivers.  The regressions are recent or introduced in
  3.14.

  Specifics:

   - There are two bugs in the ACPI PNP core that cause errors to be
     returned if optional ACPI methods are not present.  After an ACPI
     core change made in 3.14 one of those errors leads to serial port
     suspend failures on some systems.  Fix from Rafael J Wysocki.

   - A recently added PNP quirk related to Intel chipsets intorduced a
     build error in unusual configurations (PNP without PCI).  Fix from
     Bjorn Helgaas.

   - An ACPI EC workaround related to system suspend on Samsung machines
     added in 3.14 introduced a race causing some valid EC events to be
     discarded.  Fix from Kieran Clancy.

   - The acpi-cpufreq driver fails to load on some systems after a 3.14
     commit related to APIC ID parsing that overlooked one corner case.
     Fix from Lan Tianyu.

   - Fix for a recently introduced build problem in the ppc-corenet
     cpufreq driver from Tim Gardner.

   - A recent cpufreq core change to ensure serialization of frequency
     transitions for drivers with a ->target_index() callback overlooked
     the fact that some of those drivers had been doing operations
     introduced by it into the core already by themselves.  That
     resulted in a mess in which the core and the drivers try to do the
     same thing and block each other which leads to deadlocks.  Fixes
     for the powernow-k7, powernow-k6, and longhaul cpufreq drivers from
     Srivatsa S Bhat.

   - Fix for a computational error in the powernow-k6 cpufreq driver
     from Srivatsa S Bhat"

* tag 'pm+acpi-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / processor: Fix failure of loading acpi-cpufreq driver
  PNP / ACPI: Do not return errors if _DIS or _SRS are not present
  PNP: Fix compile error in quirks.c
  ACPI / EC: Process rather than discard events in acpi_ec_clear
  cpufreq: ppc-corenet-cpufreq: Fix __udivdi3 modpost error
  cpufreq: powernow-k7: Fix double invocation of cpufreq_freq_transition_begin/end
  cpufreq: powernow-k6: Fix double invocation of cpufreq_freq_transition_begin/end
  cpufreq: powernow-k6: Fix incorrect comparison with max_multipler
  cpufreq: longhaul: Fix double invocation of cpufreq_freq_transition_begin/end

Pull driver core deferred probe fix from Grant Likely:
 "Drivercore race condition fix (exposed by devicetree)

  This branch fixes a bug where a device can get stuck in the deferred
  list even though all its dependencies are met.  The bug has existed
  for a long time, but new platform conversions to device tree have
  exposed it.  This patch is needed to get those platforms working.

  This was the pending bug fix I mentioned in my previous pull request.
  Normally this would go through Greg's tree seeing that it is a
  drivercore change, but devicetree exposes the problem.  I've discussed
  with Greg and he okayed me asking you to pull directly"

* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
  drivercore: deferral race condition fix

* acpi-ec:
  ACPI / EC: Process rather than discard events in acpi_ec_clear

* acpi-processor:
  ACPI / processor: Fix failure of loading acpi-cpufreq driver

* pnp:
  PNP / ACPI: Do not return errors if _DIS or _SRS are not present
  PNP: Fix compile error in quirks.c

* pm-cpufreq:
  cpufreq: ppc-corenet-cpufreq: Fix __udivdi3 modpost error
  cpufreq: powernow-k7: Fix double invocation of cpufreq_freq_transition_begin/end
  cpufreq: powernow-k6: Fix double invocation of cpufreq_freq_transition_begin/end
  cpufreq: powernow-k6: Fix incorrect comparison with max_multipler
  cpufreq: longhaul: Fix double invocation of cpufreq_freq_transition_begin/end

Pull device mapper fixes from Mike Snitzer:
 "A few dm-thinp fixes for changes merged in 3.15-rc1.

  A dm-verity fix for an immutable biovec regression that affects 3.14+.

  A dm-cache fix to properly quiesce when using writethrough mode (3.14+)"

* tag 'dm-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache: fix writethrough mode quiescing in cache_map
  dm thin: use INIT_WORK_ONSTACK in noflush_work to avoid ODEBUG warning
  dm verity: fix biovecs hash calculation regression
  dm thin: fix rcu_read_lock being held in code that can sleep
  dm thin: irqsave must always be used with the pool->lock spinlock

Pull x86 fixes from Peter Anvin:
 "Two very small changes: one fix for the vSMP Foundation platform, and
  one to help LLVM not choke on options it doesn't understand (although
  it probably should)"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vsmp: Fix irq routing
  x86: LLVMLinux: Wrap -mno-80387 with cc-option

Pull KVM fixes from Paolo Bonzini:
 - Fix for a Haswell regression in nested virtualization, introduced
   during the merge window.
 - A fix from Oleg to async page faults.
 - A bunch of small ARM changes.
 - A trivial patch to use the new MSI-X API introduced during the merge
   window.

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: ARM: vgic: Fix the overlap check action about setting the GICD & GICC base address.
  KVM: arm/arm64: vgic: fix GICD_ICFGR register accesses
  KVM: async_pf: mm->mm_users can not pin apf->mm
  KVM: ARM: vgic: Fix sgi dispatch problem
  MAINTAINERS: co-maintainance of KVM/{arm,arm64}
  arm: KVM: fix possible misalignment of PGDs and bounce page
  KVM: x86: Check for host supported fields in shadow vmcs
  kvm: Use pci_enable_msix_exact() instead of pci_enable_msix()
  ARM: KVM: disable KVM in Kconfig on big-endian systems

Pull s390 fixes from Martin Schwidefsky:
 "Two bug fixes, one to fix a potential information leak in the BPF jit
  and common-io-layer fix for old firmware levels"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/bpf,jit: initialize A register if 1st insn is BPF_S_LDX_B_MSH
  s390/chsc: fix SEI usage on old FW levels

Pull infiniband/rdma fixes from Roland Dreier:
 "cxgb4 hardware driver fixes"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cxgb4: Update Kconfig to include Chelsio T5 adapter
  RDMA/cxgb4: Only allow kernel db ringing for T4 devs
  RDMA/cxgb4: Force T5 connections to use TAHOE congestion control
  RDMA/cxgb4: Fix endpoint mutex deadlocks

Pull parisc fixes from Helge Deller:
 "Drop the architecture-specifc value for_STK_LIM_MAX to fix stack
  related problems with GNU make"

* 'parisc-3.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Use generic uapi/asm/resource.h file
  parisc: remove _STK_LIM_MAX override