- May 15, 2012
-
-
Rafael J. Wysocki authored
* renesas-kzm9g: ARM: mach-shmobile: Use DT_MACHINE for KZM9G
-
Rafael J. Wysocki authored
* renesas-armadillo800eva: ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
-
Magnus Damm authored
Use DT_MACHINE_START() on the r8a7740 based armadillo 800 eva board. Also include a tiny DTS file to describe the board and update the Kconfig dependencies to select CONFIG_USE_OF. Signed-off-by:
Magnus Damm <damm@opensource.se> Signed-off-by:
Rafael J. Wysocki <rjw@sisk.pl>
-
Magnus Damm authored
Use DT_MACHINE_START() on the sh73a0 based KZM9G board. Also include a tiny DTS file to describe the board and update the Kconfig dependencies to select CONFIG_USE_OF. Signed-off-by:
-
- May 13, 2012
-
-
Rafael J. Wysocki authored
* renesas-kzm9g: ARM: mach-shmobile: kzm9g: enable SMP boot ARM: mach-shmobile: kzm9g: defconfig update ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key ARM: mach-shmobile: kzm9g: add SDHI support ARM: mach-shmobile: kzm9g: add MMCIF support ARM: mach-shmobile: kzm9g: correct screen direction ARM: mach-shmobile: sh73a0.h: add GPIO_NR ARM: mach-shmobile: pfc-sh73a0: fixup MSEL2CR MSEL18 for I2C-3 ARM: mach-shmobile: kzm9g: add ST1232 Touchscreen support ARM: mach-shmobile: kzm9g: add LCDC support ARM: mach-shmobile: kzm9g: add external USB Host support ARM: mach-shmobile: kzm9g: add SMSC 9221 support ARM: mach-shmobile: kzm9g: add defconfig ARM: mach-shmobile: add KZM-A9-GT board support Conflicts: arch/arm/mach-shmobile/Makefile
-
Kuninori Morimoto authored
Update the KZM9G defconfig and the code in platsmp.c to support SMP on the sh73a0 based KZM9G board. Also fix up the earlyprintk setting that was previously incorrect. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by:
-
Kuninori Morimoto authored
This patch enable GPIO-KEY/FSI, and remove debug settings, and be cleanuped by c2330e28 script Signed-off-by:
Simon Horman <horms@verge.net.au> Acked-by:
-
Kuninori Morimoto authored
This patch adds extra GPIO via PCF8757 chip, and use it as gpio-key. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
The correct screen direction of KZM9G board needs PORT226/SC settings. Signed-off-by:
-
Kuninori Morimoto authored
GPIO_NR is added in order to clarify end of GPIO array. We can add extra GPIO from it. Signed-off-by:
-
Kuninori Morimoto authored
MSEL2CR MSEL18 should be 1 if I2C-3 Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
AS3711 chip initalization is required for enabling LCDC backlight, but there is no driver for this chip. So, this patch sends its settings when boot. Signed-off-by:
-
Kuninori Morimoto authored
This patch uses r8a66597_hcd driver, since renesas_usbhs driver doesn't support external R8A66597 chip. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
This adds very basic KZM-A9-GT board (SH73a0) support Signed-off-by:
-
Kuninori Morimoto authored
This patch enable USBFunc/SHDI/MMCIF, remove debug settings, and cleanuped by c2330e28 script Signed-off-by:
-
Kuninori Morimoto authored
armadillo800eva board is using sh-eth, but clock-r8a7740 didn't care it. This clock was enabled by boot-loader. This patch fix it up. Signed-off-by:
-
Kuninori Morimoto authored
The default 2MB size of DMA coherent memory isn't enough for allocate frame buffer memory. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
We can switch CON8/CON14 by SW1.5 SDHI1 is CON8 (SW1.5 = ON) Signed-off-by:
-
Kuninori Morimoto authored
On armadillo800eva board, CD (= Card Detect) pin is not connected to SDHI0_CD. Then, we can use IRQ31 as card detect irq, but it needs chattering removal operation. We should use IRQ card detect in the future, but this patch use polling mode at this point. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
This adds very basic armadillo800eva board (R-Mobile A1) support Signed-off-by:
-
Kuninori Morimoto authored
If the clocks is always same value as the parent clock, we can use followparent_recalc() for .recalc Reported-by:
Paul Mundt <lethal@linux-sh.org> Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
R8A7740 USB needs many clocks for workaround, and it has confusing name "usb24s" and "usb24". This "usb24s" will be used by other clocks. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Current workaround of I2C on r8a7740 used mdelay(), but it was an overkill. This patch cleans up the workaround delay. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
