- May 05, 2023
-
-
Zong-Zhe Yang authored
There are two places where offload packets of 6 GHz probe would be deleted from FW, i.e. calling rtw89_fw_h2c_del_pkt_offload(). * rtw89_core_cancel_6ghz_probe_tx() * rtw89_release_pkt_list() It is possible that we try to delete the same one from FW twice. Although it might not be a big problem for now, it will depend on the runtime chip firmware. So, we add a check to avoid it. In case things becomes complex due to racing problem, we don't choose to do list_del(info->list) and kfree(info) in both sides. Besides, rtw89_fw_h2c_del_pkt_offload() will needs to wait for completion after the follow-up commit. However, rtw89_core_cancel_6ghz_probe_tx() was called in interrupt context. So, we move the stuffs of calling rtw89_fw_h2c_del_pkt_offload() from rtw89_core_cancel_6ghz_probe_tx() into a work. Then, we also need a check there before we call it. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/091966e5709cd7caecf9b81f7fd6388ae2b70a7e.camel@realtek.com
-
Zong-Zhe Yang authored
We have a pair of FW functions, rtw89_fw_h2c_add_pkt_offload() and rtw89_fw_h2c_del_pkt_offload(). The rtw89_fw_h2c_add_pkt_offload() acquires the bit itself, but the bit needs to be released by the caller of rtw89_fw_h2c_del_pkt_offload(). This looks asymmetrical and is not friendly to callers. Second, if callers always releases the bits, it might make driver unaligned to bitmap status of FW after some failures of calling rtw89_fw_h2c_del_pkt_offload(). So, this commit move bit release into rtw89_fw_h2c_del_pkt_offload(). In general, driver will call rtw89_fw_h2c_add_pkt_offload() and rtw89_fw_h2c_del_pkt_offload(), and then, SW bitmap can align with FW one. There is one exception when notify_fw is false. It happens when driver detects FW problems and is going to reset FW. Only in this case, driver needs to release bits outside rtw89_fw_h2c_del_pkt_offload(). Signed-off-by:
-
Eric Huang authored
Take EVM into consideration when doing antenna diversity, and the priority is higher than RSSI. Since EVM is more relevant to performance than RSSI, especially in OTA environment. Signed-off-by:
Eric Huang <echuang@realtek.com> Signed-off-by:
-
Eric Huang authored
RSSI statistics are grouped by CCK, OFDM or non-legacy rate. These statistics will be collected in training state for both (main/aux) antenna. There is a time period (ANTDIV_DELAY) for rate adaptive settle down before start collect statistics when switch antenna. Antenna diversity checks packet count from training state for each group and use the most one as the final RSSI for comparison, and then choose the better one as target antenna. Signed-off-by:
-
Eric Huang authored
Initialize basic antenna switch settings according to hardware module design, and set to default antenna A. The set antenna function will be called dynamically to switch antenna according to EVM and RSSI. Signed-off-by:
-
Ping-Ke Shih authored
To help debug performance problem, add EVM and SNR statistics to debugfs that shows EVM: [(26.75, 26.75) (25.75, 25.75)] SNR: 40 Signed-off-by:
-
Ping-Ke Shih authored
RSSI strength is only from PHY path A, but there are two antenna for the module which supports antenna diversity. So, set RSSI value to index 1 of RSSI array if current antenna is on antenna B. Then, debugfs can show two RSSI values with a asterisk mark on selected antenna. RSSI: -23 dBm (raw=174, prev=173) [-26, -23*] Signed-off-by:
-
Ping-Ke Shih authored
TX antenna diversity is a mechanism to select a proper antenna from two antenna for single one hardware PHY chip. It chooses antenna with better EVM or RSSI, and use GPIO to control SPDT to switch selected antenna. RFE type from efuse is used to define if a module can support TX antenna diversity when (type % 3) is 2. Signed-off-by:
-
Ping-Ke Shih authored
To be more clear to know where it gets information from PHY IE0 data, change to use struct and standard le32_get_bits() to access. This doesn't change logic at all. Signed-off-by:
-
Zhang Shurong authored
If there is a failure during copy_from_user or user-provided data buffer is invalid, rtw_debugfs_set_* should return negative error code instead of a positive value count. Fix this bug by returning correct error code. Signed-off-by:
Zhang Shurong <zhang_shurong@foxmail.com> Reviewed-by:
-
Zhang Shurong authored
If there is a failure during copy_from_user or user-provided data buffer is invalid, rtw_debugfs_copy_from_user should return negative error code instead of a positive value count. Fix this bug by returning correct error code. Moreover, the check of buffer against null is removed since it will be handled by copy_from_user. Signed-off-by:
-
Martin Kaiser authored
Remove a return statement at the end of a void function. This fixes a checkpatch warning. WARNING: void function return statements are not generally useful 6206: FILE: ./drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:6206: + return; +} Signed-off-by:
Martin Kaiser <martin@kaiser.cx> Reviewed-by:
-
Bitterblue Smith authored
The driver can receive several frames in the same USB transfer. Add the code to handle this in rtl8xxxu_parse_rxdesc24(), even though currently all the relevant chips send only one frame per USB transfer (RTL8723BU, RTL8192EU, RTL8188FU, RTL8710BU). This was tested with RTL8188FU, RTL8192EU, RTL8710BU, and RTL8192FU. Signed-off-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by:
-
Martin Kaistra authored
Set maximum number of associated stations supported in AP mode. For 8188f, the maximum number of supported macids is 16, reserve one for broadcast/multicast frames. Signed-off-by:
Martin Kaistra <martin.kaistra@linutronix.de> Reviewed-by:
-
Martin Kaistra authored
Everything is in place now for AP mode, we can tell the system that we support it. Put the feature behind a flag in priv->fops, because it is not (yet) implemented for all chips. Signed-off-by:
-
Martin Kaistra authored
As this driver uses HAS_RATE_CONTROL, rate_flags will not be provided by mac80211. Stop using tx_info->control.rates[0].flags and ieee80211_get_rts_cts_rate() and use rts_threshold and bss_conf.use_cts_prot instead to determine when to use RTS and CTS. Send RTS with 24M rate like the vendor drivers. Also set this RTS rate for ampdu_enable = true, because we also enable RTS for these frames. Signed-off-by:
-
Martin Kaistra authored
As this driver uses HAS_RATE_CONTROL, tx_rates will not be provided by mac80211. For some frames c->control.rates[0].idx is negative, which means ieee80211_get_tx_rate() will print a warning and return NULL. Only management frames have USE_DRIVER_RATE set, so for all others the rate info of txdesc is ignored anyway. Remove call to ieee80211_get_tx_rate() and send management frames with 1M (rate info = 0). Signed-off-by:
-
Martin Kaistra authored
When RCR_CHECK_BSSID_MATCH is set in AP mode, we don't receive any data frames. Rearrange RCR bits to filter flags to match other realtek drivers and remove RCR_CHECK_BSSID_MATCH in AP mode. Signed-off-by:
-
Martin Kaistra authored
Beacon frames are generated by the HW and therefore contain a HW generated seq number. Enable HW sequence number for other frames to match that. mac80211 will tell us via IEEE80211_TX_CTL_ASSIGN_SEQ when that is necessary. Signed-off-by:
-
Martin Kaistra authored
The HW maintains a rate_mask for each connection, referenced by the macid. Add a parameter to update_rate_mask and add the macid to the h2c call in the gen2 implementation. Also extend refresh_rate_mask to get the macid from sta_info. Signed-off-by:
-
Martin Kaistra authored
Add a parameter macid to fill_txdesc(), implement setting it for the gen2 version. This is used to tell the HW who the recipient of the packet is, so that the appropriate data rate can be selected. Signed-off-by:
-
Martin Kaistra authored
In AP mode, sta_add() gets called when a new STA gets associated to us. Call rtl8xxxu_refresh_rate_mask() to set a rate mask for the newly connected STA (referenced by the macid) and then send a media connnect report. Ignore the call to sta_add() in station mode. Reserve one macid for broadcast/multicast packets in init. Signed-off-by:
-
Martin Kaistra authored
In AP mode, when multiple STAs connect to us, we need to set an initial rate mask for each of them. This initialisation should happen regardless of the rssi_level saved in the priv struct. Add a parameter called force to rtl8xxxu_refresh_rate_mask() which will be used for this initialisation. Signed-off-by:
-
Martin Kaistra authored
This allows to tell the HW if a connection is made to a STA or an AP. Add the implementation for the gen2 version. Signed-off-by:
-
Martin Kaistra authored
The report_connect function has had a macid parameter from the beginning, but it has not been used, because in STA mode, the value was always zero. As it can now have different values in AP mode, actually wire it up to the H2C command. Signed-off-by:
-
Martin Kaistra authored
Use the sequence from the vendor driver for setting up the beacon related registers. Also set the MAC address register here, in case the MAC address for the new interface should be different from what was set in rtl8xxxu_init_device(). This happens for example with the hostapd config option "bssid". Signed-off-by:
-
Martin Kaistra authored
The default setting in hostapd.conf for rts threshold is -1, which means disabled. Allow to set it. Signed-off-by:
-
Martin Kaistra authored
Update beacon content if TIM bitmap maintained by mac80211 is changed. Signed-off-by:
-
Martin Kaistra authored
Add a workqueue to update the beacon contents asynchronously and implement downloading the beacon to the HW and starting beacon tx like the vendor driver. Signed-off-by:
-
Martin Kaistra authored
Use the special beacon queue for beacon frames instead of the management frame queue. They will be put in a special area called reserved page and send out periodically when in AP mode. Signed-off-by:
-
Martin Kaistra authored
This gets called at the start of AP mode operation. Set bssid, beacon interval and send a connect report to the HW. Signed-off-by:
-
- Apr 25, 2023
-
-
wuych authored
Pointer variables of void * type do not require type cast. Signed-off-by:
wuych <yunchuan@nfschina.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Christian Marangi authored
Fix inconsistent indeinting in m88e1318_led_blink_set reported by kernel test robot, probably done by the presence of an if condition dropped in later revision of the same code. Reported-by:
kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202304240007.0VEX8QYG-lkp@intel.com/ Fixes: ea9e8648 ("net: phy: marvell: Implement led_blink_set()") Signed-off-by:
Christian Marangi <ansuelsmth@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230423172800.3470-1-ansuelsmth@gmail.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Horatiu Vultur authored
When the action of an xdp program was XDP_TX, lan966x was creating a xdp_frame and use this one to send the frame back. But it is also possible to send back the frame without needing a xdp_frame, because it is possible to send it back using the page. And then once the frame is transmitted is possible to use directly page_pool_recycle_direct as lan966x is using page pools. This would save some CPU usage on this path, which results in higher number of transmitted frames. Bellow are the statistics: Frame size: Improvement: 64 ~8% 256 ~11% 512 ~8% 1000 ~0% 1500 ~0% Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by:
Alexander Lobakin <aleksander.lobakin@intel.com> Link: https://lore.kernel.org/r/20230422142344.3630602-1-horatiu.vultur@microchip.com Signed-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Alexei Starovoitov says: ==================== pull-request: bpf-next 2023-04-24 We've added 5 non-merge commits during the last 3 day(s) which contain a total of 7 files changed, 87 insertions(+), 44 deletions(-). The main changes are: 1) Workaround for bpf iter selftest due to lack of subprog support in precision tracking, from Andrii. 2) Disable bpf_refcount_acquire kfunc until races are fixed, from Dave. 3) One more test_verifier test converted from asm macro to asm in C, from Eduard. 4) Fix build with NETFILTER=y INET=n config, from Florian. 5) Add __rcu_read_{lock,unlock} into deny list, from Yafang. * tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: selftests/bpf: avoid mark_all_scalars_precise() trigger in one of iter tests bpf: Add __rcu_read_{lock,unlock} into btf id deny list bpf: Disable bpf_refcount_acquire kfunc calls until race conditions are fixed selftests/bpf: verifier/prevent_map_lookup converted to inline assembly bpf: fix link failure with NETFILTER=y INET=n ==================== Link: https://lore.kernel.org/r/20230425005648.86714-1-alexei.starovoitov@gmail.com Signed-off-by: -
Jakub Kicinski authored
Gerhard Engleder says: ==================== tsnep: XDP socket zero-copy support Implement XDP socket zero-copy support for tsnep driver. I tried to follow existing drivers like igc as far as possible. But one main difference is that tsnep does not need any reconfiguration for XDP BPF program setup. So I decided to keep this behavior no matter if a XSK pool is used or not. As a result, tsnep starts using the XSK pool even if no XDP BPF program is available. Another difference is that I tried to prevent potentially failing allocations during XSK pool setup. E.g. both memory models for page pool and XSK pool are registered all the time. Thus, XSK pool setup cannot end up with not working queues. Some prework is done to reduce the last two XSK commits to actual XSK changes. ==================== Link: https://lore.kernel.org/r/20230421194656.48063-1-gerhard@engleder-embedded.com Signed-off-by:
-
Gerhard Engleder authored
Send and complete XSK pool frames within TX NAPI context. NAPI context is triggered by ndo_xsk_wakeup. Test results with A53 1.2GHz: xdpsock txonly copy mode, 64 byte frames: pps pkts 1.00 tx 284,409 11,398,144 Two CPUs with 100% and 10% utilization. xdpsock txonly zero-copy mode, 64 byte frames: pps pkts 1.00 tx 511,929 5,890,368 Two CPUs with 100% and 1% utilization. xdpsock l2fwd copy mode, 64 byte frames: pps pkts 1.00 rx 248,985 7,315,885 tx 248,921 7,315,885 Two CPUs with 100% and 10% utilization. xdpsock l2fwd zero-copy mode, 64 byte frames: pps pkts 1.00 rx 254,735 3,039,456 tx 254,735 3,039,456 Two CPUs with 100% and 4% utilization. Packet rate increases and CPU utilization is reduced in both cases. Signed-off-by:Gerhard Engleder <gerhard@engleder-embedded.com> Reviewed-by:
Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by:
-
Gerhard Engleder authored
Add support for XSK zero-copy to RX path. The setup of the XSK pool can be done at runtime. If the netdev is running, then the queue must be disabled and enabled during reconfiguration. This can be done easily with functions introduced in previous commits. A more important property is that, if the netdev is running, then the setup of the XSK pool shall not stop the netdev in case of errors. A broken netdev after a failed XSK pool setup is bad behavior. Therefore, the allocation and setup of resources during XSK pool setup is done only before any queue is disabled. Additionally, freeing and later allocation of resources is eliminated in some cases. Page pool entries are kept for later use. Two memory models are registered in parallel. As a result, the XSK pool setup cannot fail during queue reconfiguration. In contrast to other drivers, XSK pool setup and XDP BPF program setup are separate actions. XSK pool setup can be done without any XDP BPF program. The XDP BPF program can be added, removed or changed without any reconfiguration of the XSK pool. Test results with A53 1.2GHz: xdpsock rxdrop copy mode, 64 byte frames: pps pkts 1.00 rx 856,054 10,625,775 Two CPUs with both 100% utilization. xdpsock rxdrop zero-copy mode, 64 byte frames: pps pkts 1.00 rx 889,388 4,615,284 Two CPUs with 100% and 20% utilization. Packet rate increases and CPU utilization is reduced. 100% CPU load seems to the base load. This load is consumed by ksoftirqd just for dropping the generated packets without xdpsock running. Using batch API reduced CPU utilization slightly, but measurements are not stable enough to provide meaningful numbers. Signed-off-by: -
Gerhard Engleder authored
The function tsnep_rx_poll() is already pretty long and the skb receive action can be reused for XSK zero-copy support. Move page based skb receive to separate function. Signed-off-by:
-
Gerhard Engleder authored
Move queue enable and disable code to separate functions. This way the activation and deactivation of the queues are defined actions, which can be used in future execution paths. This functions will be used for the queue reconfiguration at runtime, which is necessary for XSK zero-copy support. Signed-off-by:
-
