- Jan 28, 2023
-
-
Christian Hewitt authored
The sound device is enabled by default so remove the redundant status. Signed-off-by:
Christian Hewitt <christianshewitt@gmail.com> Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230127142221.3718184-3-christianshewitt@gmail.com Signed-off-by:
-
Christian Hewitt authored
For proper warm (re)boot from SD card the BPI-M5 board requires TFLASH_VDD_EN and VDDIO_C pins to be switched to high impedance mode. This can be achieved using OPEN_DRAIN instead of ACTIVE_HIGH to leave the GPIO pins in input mode and retain high state (pin has the pull-up). This change is inspired by meson-sm1-odroid.dtsi where OPEN_DRAIN has been used to resolve similar problems with the Odroid C4 board (TF_IO in the C4 dts is the equivalent regulator). Fixes: 976e9201 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts") Suggested-by:
-
- Jan 27, 2023
-
-
Christian Hewitt authored
Setting dr_mode to "host" prevents otg which can be useful on a board with limited connectivity options. So don't force host mode. Fixes: 26d1400f ("arm64: dts: amlogic: add support for Radxa Zero") Signed-off-by:
-
David Heidelberg authored
No functional changes. Adjust to comply with dt-schema requirements and make it possible to validate values. Acked-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
David Heidelberg <david@ixit.cz> Link: https://lore.kernel.org/r/20230126193732.69699-1-david@ixit.cz Signed-off-by:
-
- Jan 26, 2023
-
-
Neil Armstrong authored
ODROID-N2L is a variant SBC in small form factor and some peripherals are removed from ODROID-N2PLUS based on S922X SoC. - On-board ethernet is removed - On-board RTC is removed - USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports are available - Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink is recommended or a tall passive sink is optional - 3.5mm earjack is removed - IR remote receiver is removed - MIPI DSI port is added new but not yet supported Signed-off-by:
Dongjin Kim <tobetter@gmail.com> Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-3-8d3fea6d403d@linaro.org Signed-off-by:
-
Neil Armstrong authored
In order to introduce Odroid-N2L which is basically an Odroid-N2+ without some on-board peripherals (Ethernet, RTC, Hub, Jack), move the common nodes into a new meson-g12b-odroid.dtsi which will will be the common dtsi for all the Odroid-N2 derived boards. Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-2-8d3fea6d403d@linaro.org Signed-off-by:
-
Neil Armstrong authored
ODROID-N2L is a variant SBC in small form factor and some peripherals are removed from ODROID-N2PLUS based on S922X SoC. - On-board ethernet is removed - On-board RTC is removed - USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports are available - Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink is recommended or a tall passive sink is optional - 3.5mm earjack is removed - IR remote receiver is removed - MIPI DSI port is added Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-1-8d3fea6d403d@linaro.org Signed-off-by:
-
Neil Armstrong authored
Add an active trip tied to the on-board fan cooling device, which is better than describing it along the passive cooling maps. Fixes: 33b14f66 ("arm64: dts: meson: add initial device-tree for ODROID-HC4") Reported-by:
Ricardo Pardini <ricardo@pardini.net> Link: https://lore.kernel.org/r/20230124-topic-odroid-hc4-upstream-fix-fan-trip-v1-1-b0c6aa355d93@linaro.org Tested-by:
-
Christian Hewitt authored
Add initial support for the HDMI and Analogue i2s audio outputs. Signed-off-by:
-
Christian Hewitt authored
The Broadcom WiFi/BT SDIO nodes are now inherited from the P212 common dtsi so we can remove them from the VIM1 board dts. Signed-off-by:
-
Christian Hewitt authored
Cosmetic-only change to alpha-sort the pwm_ef node. Signed-off-by:
-
Christian Hewitt authored
The P212 has a combined WiFi/BT module. The BT side is already enabled in the dtsi but the WiFi side is not. Let's enable the WiFi module. Signed-off-by:
-
Neil Armstrong authored
Fixes: pmic@1c: '#clock-cells' is a required property pmic@1c: 'switch-supply' does not match any of the regexes: 'pinctrl-[0-9]+' The switch supply is described by vcc9-supply per bindings documentation. Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-14-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: leds: status: {...} is not of type 'array' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-13-44351528957e@linaro.org Signed-off-by: -
Neil Armstrong authored
Fixes: leds: status: {...} is not of type 'array' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-12-44351528957e@linaro.org Signed-off-by: -
Neil Armstrong authored
Fixes: adc_keys: 'key' does not match any of the regexes: '^button-', 'pinctrl-[0-9]+' Also fix the invalid "adc_keys" node name. Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-11-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: adc-keys: 'update-button' does not match any of the regexes: '^button-', 'pinctrl-[0-9]+' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-10-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: bus@c8834000: eth-phy-mux: {...} should not be valid under {'type': 'object'} Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-9-44351528957e@linaro.org Signed-off-by: -
Neil Armstrong authored
Fixes: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-[0-9a-f])*$' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-8-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-[0-9a-f])*$' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-7-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: bus@c8834000: rng: {...} should not be valid under {'type': 'object'} Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-6-44351528957e@linaro.org Signed-off-by: -
Neil Armstrong authored
Fixes: bluetooth: 'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-5-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: usb@ffe09080: 'phy-supply' does not match any of the regexes: '^usb@[0-9a-f]+$', 'pinctrl-[0-9]+' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-4-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: scpi: sensors:compatible: 'oneOf' conditional failed, one must be fixed: ['amlogic,meson-gxbb-scpi-sensors'] is too short 'arm,scpi-sensors' was expected Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-3-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: scpi: clocks: 'clock-controller' does not match any of the regexes: '^clocks-[0-9a-f]+$', 'pinctrl-[0-9]+' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-2-44351528957e@linaro.org Signed-off-by:
-
Neil Armstrong authored
Fixes: scpi: clocks: 'clock-controller' does not match any of the regexes: '^clocks-[0-9a-f]+$', 'pinctrl-[0-9]+' Link: https://lore.kernel.org/r/20230124-b4-amlogic-bindings-fixups-v1-1-44351528957e@linaro.org Signed-off-by:
-
- Jan 24, 2023
-
-
Heiner Kallweit authored
mmc-controller.yaml defines "^mmc(@.*)?$" as node name pattern. In preparation of adding schema-based validation fix the node name in two affected files. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
-
- Jan 19, 2023
-
-
Christian Hewitt authored
Amlogic G12A devices experience CPU stalls and random board wedges when the system idles and CPU cores clock down to lower opp points. Recent vendor kernels include a change to remove 100-250MHz and other distro sources also remove the 500/667MHz points. Unless all 100-667Mhz opps are removed or the CPU governor forced to performance stalls are still observed, so let's remove them to improve stability and uptime. Fixes: b190056f ("arm64: dts: meson-g12a: add cpus OPP table") Signed-off-by:
-
- Jan 13, 2023
-
-
Martin Blumenstingl authored
Node names should be generic and use hyphens instead of underscores to not cause warnings. Also nodes without a reg property should not have a unit-address. Change the scpi_dvfs node to use clock-controller as node name without a unit address (since it does not have a reg property). Fixes: 70db166a ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes") Signed-off-by:
-
Martin Blumenstingl authored
Documentation/devicetree/bindings/net/ethernet-phy.yaml defines that the node name for Ethernet PHYs should match the following pattern: ^ethernet-phy(@[a-f0-9]+)?$ Replace the underscore with a hyphen to adhere to this binding. Fixes: 280c17df ("arm64: dts: meson: g12a: add mdio multiplexer") Signed-off-by:
-
Martin Blumenstingl authored
Unit names should use hyphens instead of underscores to not cause warnings. Fixes: bfe59f92 ("ARM64: dts: amlogic: gxbb: Enable NVMEM") Suggested-by:
Vyacheslav Bocharov <adeep@lexina.in> Signed-off-by:
-
Martin Blumenstingl authored
Node names should use hyphens instead of underscores to not cause warnings. Fixes: 59ec069d ("arm64: dts: meson-axg: add support for JetHub D1p (j110)") Signed-off-by:
-
Martin Blumenstingl authored
Node names should use hyphens instead of underscores to not cause warnings. Fixes: abfaae24 ("arm64: dts: meson-gxl: add support for JetHub H1") Suggested-by:
-
Martin Blumenstingl authored
Unit addresses should be written using lower-case hex characters. Use wifi_mac@c to fix a yaml schema validation error once the eFuse dt-bindings have been converted to a yaml schema: efuse: Unevaluated properties are not allowed ('wifi_mac@C' was unexpected) Also node names should use hyphens instead of underscores as the latter can also cause warnings. Fixes: abfaae24 ("arm64: dts: meson-gxl: add support for JetHub H1") Acked-by:
-
- Jan 02, 2023
-
-
Tomeu Vizoso authored
This "NPU" is very similar to the Vivante GPUs and Etnaviv works well with it with just a few small changes. v2: Add reference to RESET_NNA (Neil) v3: Fix indentation (Neil) Signed-off-by:
Tomeu Vizoso <tomeu.vizoso@collabora.com> Reviewed-by:
-
Neil Armstrong authored
Merge branch 'v6.3/bindings' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into v6.3/arm64-dt Signed-off-by:
-
Tomeu Vizoso authored
Add define for the NNA power domain for the NPU in the G12A. Signed-off-by:
-
Tomeu Vizoso authored
Doesn't appear in the TRM I have, but it is used by the downstream galcore driver. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
-
Krzysztof Kozlowski authored
The node names should be generic and DT schema expects certain pattern: amlogic/meson-sm1-bananapi-m5.dtb: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' Signed-off-by:
-
- Dec 26, 2022
-
-
Linus Torvalds authored
-
