- Oct 02, 2020
-
-
Pawel Laszczak authored
USB2.0 PHY hangs in Rx Compliance test when the incoming packet amplitude is varied below and above the Squelch Level of Receiver during the active packet multiple times. Version 1 of the controller allows PHY to be reset when RX fail condition is detected to work around the above issue. This feature is disabled by default and needs to be enabled using a bit from the newly added PHYRST_CFG register. This patch enables the workaround. There is no way to know controller version before device controller is started and the workaround needs to be applied for both host and device modes, so we rely on a DT property do decide when to apply the workaround. Signed-off-by:
Pawel Laszczak <pawell@cadence.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org>
-
Roger Quadros authored
Controller version 0x0002450D has USB2 PHY RX sensitivity issues that needs to be worked around by enabling phyrst-a-enable bit in PHYRST_CFG register. There is no way to know controller version before device controller is started and the workaround needs to be applied for both host and device modes, so we add this DT property. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Roger Quadros authored
Converts cdns-usb3.txt to YAML schema cdns,usb3.yaml Reviewed-by:
-
Neil Armstrong authored
The Amlogic AXG is close to the GXL Glue but with a single OTG PHY. It needs the same init sequence as GXL & GXM, but it seems it doesn't need the host disconnect bit. Reviewed-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Reviewed-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Neil Armstrong authored
The Amlogic AXG is close to the GXL Glue but with a single OTG PHY. Reviewed-by:
-
Lad Prabhakar authored
Document r8a774e1 xhci support. The driver will use the fallback compatible string "renesas,rcar-gen3-xhci", therefore no driver change is needed. Reviewed-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by:
Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com> Acked-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Linus Walleij authored
This switches the PCH UDC driver to use GPIO descriptors. The way this is supposed to be used is confusing. The code contains the following: /* GPIO port for VBUS detecting */ static int vbus_gpio_port = -1; /* GPIO port number (-1:Not used) */ So a hardcoded GPIO number in the code. Further the probe() path very clearly will exit if the GPIO is not found, so this driver can only be configured by editing the code, hard-coding a GPIO number into this variable. This is simply not how we do things. My guess is that this is used in products by patching a GPIO number into this variable and shipping a kernel that is compile-time tailored for the target system. I switched this mechanism to using a GPIO descriptor associated with the parent PCI device. This can be added by using the 16bit subsystem ID or similar to identify which exact machine we are running on and what GPIO is present on that machine, and then add a GPIO descriptor using gpiod_add_lookup_table() from <linux/gpio/machine.h>. Since I don't have any target systems I cannot add this but I'm happy to help. I put in a FIXME so the people actually using this driver knows what to do. Cc: Felipe Balbi <balbi@kernel.org> Tested-by:Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Peter Chen authored
Add imx glue layer runtime pm implementation, and the runtime pm is default off. Reviewed-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Peter Chen authored
Introduce runtime PM and wakeup interrupt handler for cdns3, the runtime PM is default off since other cdns3 may not implement glue layer support for runtime PM. One typical wakeup event use case is xHCI runtime suspend will clear USBCMD.RS bit, after that the xHCI will not trigger any interrupts, so its parent (cdns core device) needs to resume xHCI device when any (wakeup) events occurs at host port. When the controller is in low power mode, the lpm flag will be set. The interrupt triggered later than lpm flag is set considers as wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup occurs, it first disables interrupt to avoid later interrupt occurrence since the controller is in low power mode at that time, and access registers may be invalid at that time. At wakeup handler, it will call pm_request_resume to wakeup xHCI device, and at runtime resume handler, it will enable interrupt again. The API platform_suspend is introduced for glue layer to implement platform specific PM sequence. Reviewed-by:
-
Peter Chen authored
Since we have both USB2 and USB3 PHYs for cdns3 controller, it is better we have unity APIs to handle both USB2 and USB3's power, it could simplify code for error handling and further power management implementation. Reviewed-by:
Jun Li <jun.li@nxp.com> Signed-off-by:
-
YueHaibing authored
It is never used, so can be removed. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Li Jun authored
Do not try to queue a drd work if dr_mode is not USB_DR_MODE_OTG because the work is not inited, this may be triggered by user try to change mode file of debugfs on a single role port, which will cause below kernel dump: [ 60.115529] ------------[ cut here ]------------ [ 60.120166] WARNING: CPU: 1 PID: 627 at kernel/workqueue.c:1473 __queue_work+0x46c/0x520 [ 60.128254] Modules linked in: [ 60.131313] CPU: 1 PID: 627 Comm: sh Not tainted 5.7.0-rc4-00022-g914a586-dirty #135 [ 60.139054] Hardware name: NXP i.MX8MQ EVK (DT) [ 60.143585] pstate: a0000085 (NzCv daIf -PAN -UAO) [ 60.148376] pc : __queue_work+0x46c/0x520 [ 60.152385] lr : __queue_work+0x314/0x520 [ 60.156393] sp : ffff8000124ebc40 [ 60.159705] x29: ffff8000124ebc40 x28: ffff800011808018 [ 60.165018] x27: ffff800011819ef8 x26: ffff800011d39980 [ 60.170331] x25: ffff800011808018 x24: 0000000000000100 [ 60.175643] x23: 0000000000000013 x22: 0000000000000001 [ 60.180955] x21: ffff0000b7c08e00 x20: ffff0000b6c31080 [ 60.186267] x19: ffff0000bb99bc00 x18: 0000000000000000 [ 60.191579] x17: 0000000000000000 x16: 0000000000000000 [ 60.196891] x15: 0000000000000000 x14: 0000000000000000 [ 60.202202] x13: 0000000000000000 x12: 0000000000000000 [ 60.207515] x11: 0000000000000000 x10: 0000000000000040 [ 60.212827] x9 : ffff800011d55460 x8 : ffff800011d55458 [ 60.218138] x7 : ffff0000b7800028 x6 : 0000000000000000 [ 60.223450] x5 : ffff0000b7800000 x4 : 0000000000000000 [ 60.228762] x3 : ffff0000bb997cc0 x2 : 0000000000000001 [ 60.234074] x1 : 0000000000000000 x0 : ffff0000b6c31088 [ 60.239386] Call trace: [ 60.241834] __queue_work+0x46c/0x520 [ 60.245496] queue_work_on+0x6c/0x90 [ 60.249075] dwc3_set_mode+0x48/0x58 [ 60.252651] dwc3_mode_write+0xf8/0x150 [ 60.256489] full_proxy_write+0x5c/0xa8 [ 60.260327] __vfs_write+0x18/0x40 [ 60.263729] vfs_write+0xdc/0x1c8 [ 60.267045] ksys_write+0x68/0xf0 [ 60.270360] __arm64_sys_write+0x18/0x20 [ 60.274286] el0_svc_common.constprop.0+0x68/0x160 [ 60.279077] do_el0_svc+0x20/0x80 [ 60.282394] el0_sync_handler+0x10c/0x178 [ 60.286403] el0_sync+0x140/0x180 [ 60.289716] ---[ end trace 70b155582e2b7988 ]--- Signed-off-by:
-
Zqiang authored
Fix this by increase object reference count. BUG: KASAN: use-after-free in __lock_acquire+0x3fd4/0x4180 kernel/locking/lockdep.c:3831 Read of size 8 at addr ffff8880683b0018 by task syz-executor.0/3377 CPU: 1 PID: 3377 Comm: syz-executor.0 Not tainted 5.6.11 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xce/0x128 lib/dump_stack.c:118 print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374 __kasan_report+0x131/0x1b0 mm/kasan/report.c:506 kasan_report+0x12/0x20 mm/kasan/common.c:641 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:135 __lock_acquire+0x3fd4/0x4180 kernel/locking/lockdep.c:3831 lock_acquire+0x127/0x350 kernel/locking/lockdep.c:4488 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x35/0x50 kernel/locking/spinlock.c:159 printer_ioctl+0x4a/0x110 drivers/usb/gadget/function/f_printer.c:723 vfs_ioctl fs/ioctl.c:47 [inline] ksys_ioctl+0xfb/0x130 fs/ioctl.c:763 __do_sys_ioctl fs/ioctl.c:772 [inline] __se_sys_ioctl fs/ioctl.c:770 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:770 do_syscall_64+0x9e/0x510 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4531a9 Code: ed 60 fc ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 bb 60 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fd14ad72c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 000000000073bfa8 RCX: 00000000004531a9 RDX: fffffffffffffff9 RSI: 000000000000009e RDI: 0000000000000003 RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000004bbd61 R13: 00000000004d0a98 R14: 00007fd14ad736d4 R15: 00000000ffffffff Allocated by task 2393: save_stack+0x21/0x90 mm/kasan/common.c:72 set_track mm/kasan/common.c:80 [inline] __kasan_kmalloc.constprop.3+0xa7/0xd0 mm/kasan/common.c:515 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:529 kmem_cache_alloc_trace+0xfa/0x2d0 mm/slub.c:2813 kmalloc include/linux/slab.h:555 [inline] kzalloc include/linux/slab.h:669 [inline] gprinter_alloc+0xa1/0x870 drivers/usb/gadget/function/f_printer.c:1416 usb_get_function+0x58/0xc0 drivers/usb/gadget/functions.c:61 config_usb_cfg_link+0x1ed/0x3e0 drivers/usb/gadget/configfs.c:444 configfs_symlink+0x527/0x11d0 fs/configfs/symlink.c:202 vfs_symlink+0x33d/0x5b0 fs/namei.c:4201 do_symlinkat+0x11b/0x1d0 fs/namei.c:4228 __do_sys_symlinkat fs/namei.c:4242 [inline] __se_sys_symlinkat fs/namei.c:4239 [inline] __x64_sys_symlinkat+0x73/0xb0 fs/namei.c:4239 do_syscall_64+0x9e/0x510 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 3368: save_stack+0x21/0x90 mm/kasan/common.c:72 set_track mm/kasan/common.c:80 [inline] kasan_set_free_info mm/kasan/common.c:337 [inline] __kasan_slab_free+0x135/0x190 mm/kasan/common.c:476 kasan_slab_free+0xe/0x10 mm/kasan/common.c:485 slab_free_hook mm/slub.c:1444 [inline] slab_free_freelist_hook mm/slub.c:1477 [inline] slab_free mm/slub.c:3034 [inline] kfree+0xf7/0x410 mm/slub.c:3995 gprinter_free+0x49/0xd0 drivers/usb/gadget/function/f_printer.c:1353 usb_put_function+0x38/0x50 drivers/usb/gadget/functions.c:87 config_usb_cfg_unlink+0x2db/0x3b0 drivers/usb/gadget/configfs.c:485 configfs_unlink+0x3b9/0x7f0 fs/configfs/symlink.c:250 vfs_unlink+0x287/0x570 fs/namei.c:4073 do_unlinkat+0x4f9/0x620 fs/namei.c:4137 __do_sys_unlink fs/namei.c:4184 [inline] __se_sys_unlink fs/namei.c:4182 [inline] __x64_sys_unlink+0x42/0x50 fs/namei.c:4182 do_syscall_64+0x9e/0x510 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8880683b0000 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 24 bytes inside of 1024-byte region [ffff8880683b0000, ffff8880683b0400) The buggy address belongs to the page: page:ffffea0001a0ec00 refcount:1 mapcount:0 mapping:ffff88806c00e300 index:0xffff8880683b1800 compound_mapcount: 0 flags: 0x100000000010200(slab|head) raw: 0100000000010200 0000000000000000 0000000600000001 ffff88806c00e300 raw: ffff8880683b1800 000000008010000a 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Reported-by:
Kyungtae Kim <kt0755@gmail.com> Signed-off-by:
Zqiang <qiang.zhang@windriver.com> Signed-off-by:
-
Florian Fainelli authored
The Broadcom BDC driver did not have a MAINTAINERS entry which made it escape review from Al and myself, add an entry so the relevant mailing lists and people are copied. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Michał Mirosław authored
Make debugging real problems easier by not trying to disable an EP that was not yet enabled. Reviewed-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by:
-
Tao Ren authored
This is a follow-on patch for commit a23be4ed ("usb: gadget: aspeed: improve vhub port irq handling"): for_each_set_bit() is replaced with simple for() loop because for() loop runs faster on ASPEED BMC. Signed-off-by:
Tao Ren <rentao.bupt@gmail.com> Signed-off-by:
-
Felipe Balbi authored
no functional changes Signed-off-by: -
Felipe Balbi authored
no functional changes Signed-off-by: -
Felipe Balbi authored
no functional changes Signed-off-by: -
Felipe Balbi authored
no functional changes Signed-off-by: -
Felipe Balbi authored
no functional changes Signed-off-by: -
Felipe Balbi authored
no functional changes Signed-off-by: -
Felipe Balbi authored
no functional changes Signed-off-by: -
Felipe Balbi authored
no functional changes. Signed-off-by: -
Felipe Balbi authored
no functional changes. Signed-off-by: -
Felipe Balbi authored
Fix the following sparse warning: drivers/usb/dwc3/trace.c: note: in included file (through drivers/usb/dwc3/trace.h): drivers/usb/dwc3/debug.h:374:39: warning: cast to non-scalar Signed-off-by: -
Felipe Balbi authored
Coccinelle suggests using PTR_ERR_OR_ZERO(). Signed-off-by: -
Sandeep Maheswaram authored
Add interconnect support in dwc3-qcom driver to vote for bus bandwidth. This requires for two different paths - from USB to DDR. The other is from APPS to USB. Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
Sandeep Maheswaram <sanm@codeaurora.org> Signed-off-by:
Chandana Kishori Chiluveru <cchiluve@codeaurora.org> Signed-off-by:
-
Linus Walleij authored
The UDC NET2272 driver includes <linux/gpio.h> but does not use any symbols from this file, so drop the include. Cc: Felipe Balbi <balbi@kernel.org> Signed-off-by:
-
Peter Chen authored
Add Cadence USB3 DRD IP driver entry Signed-off-by:
-
- Sep 24, 2020
-
-
Cristian Birsan authored
Enable usb device for sam9x60ek board. Signed-off-by:
Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by:
-
Cristian Birsan authored
The DPRAM memory from the USB High Speed Device Port (UDPHS) hardware block was increased. This patch updates the endpoint allocation for sam9x60 to take advantage of this larger memory. At the same time the constraint to allocate the endpoints in order was lifted. To handle old and new hardware in the same driver the ep_prealloc was added. Signed-off-by:
-
Cristian Birsan authored
Use 1 bank endpoints for control transfers Signed-off-by:
-
Cristian Birsan authored
Simplify the endpoint allocation and cleanup the code. Signed-off-by:
-
Cristian Birsan authored
Add sam9x60 binding. Signed-off-by:
-
Claudiu Beznea authored
Instead of trying to match every possible compatible use of_find_matching_node_and_match() and pass the compatible array. Signed-off-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by:
-
Martin Blumenstingl authored
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled earlier) when usb_add_gadget_udc() has failed. This ensures that the debugfs entries created by dwc2_debugfs_init() as well as the HCD are cleaned up in the error path. Fixes: 207324a3 ("usb: dwc2: Postponed gadget registration to the udc class driver") Acked-by:
Minas Harutyunyan <hminas@synopsys.com> Signed-off-by:
-
Thinh Nguyen authored
The user may have more information to override the HW parameter to specify the maximum_speed. However, if the user specifies a maximum_speed that the controller doesn't support, print out a warning. Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
-
Thinh Nguyen authored
If the maximum_speed is not specified, default the device speed base on its HW capability. Don't prematurely check HW capability before validating the maximum_speed device property. The device property takes precedence in dwc->maximum_speed. Fixes: 0e1e5c47 ("usb: dwc3: add support for USB 2.0-only core configuration") Reported-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by:
-
Nathan Chancellor authored
When booting up on a Raspberry Pi 4 with Control Flow Integrity checking enabled, the following warning/panic happens: [ 1.626435] CFI failure (target: dwc2_set_bcm_params+0x0/0x4): [ 1.632408] WARNING: CPU: 0 PID: 32 at kernel/cfi.c:30 __cfi_check_fail+0x54/0x5c [ 1.640021] Modules linked in: [ 1.643137] CPU: 0 PID: 32 Comm: kworker/0:1 Not tainted 5.8.0-rc6-next-20200724-00051-g89ba619726de #1 [ 1.652693] Hardware name: Raspberry Pi 4 Model B Rev 1.2 (DT) [ 1.658637] Workqueue: events deferred_probe_work_func [ 1.663870] pstate: 60000005 (nZCv daif -PAN -UAO BTYPE=--) [ 1.669542] pc : __cfi_check_fail+0x54/0x5c [ 1.673798] lr : __cfi_check_fail+0x54/0x5c [ 1.678050] sp : ffff8000102bbaa0 [ 1.681419] x29: ffff8000102bbaa0 x28: ffffab09e21c7000 [ 1.686829] x27: 0000000000000402 x26: ffff0000f6e7c228 [ 1.692238] x25: 00000000fb7cdb0d x24: 0000000000000005 [ 1.697647] x23: ffffab09e2515000 x22: ffffab09e069a000 [ 1.703055] x21: 4c550309df1cf4c1 x20: ffffab09e2433c60 [ 1.708462] x19: ffffab09e160dc50 x18: ffff0000f6e8cc78 [ 1.713870] x17: 0000000000000041 x16: ffffab09e0bce6f8 [ 1.719278] x15: ffffab09e1c819b7 x14: 0000000000000003 [ 1.724686] x13: 00000000ffffefff x12: 0000000000000000 [ 1.730094] x11: 0000000000000000 x10: 00000000ffffffff [ 1.735501] x9 : c932f7abfc4bc600 x8 : c932f7abfc4bc600 [ 1.740910] x7 : 077207610770075f x6 : ffff0000f6c38f00 [ 1.746317] x5 : 0000000000000000 x4 : 0000000000000000 [ 1.751723] x3 : 0000000000000000 x2 : 0000000000000000 [ 1.757129] x1 : ffff8000102bb7d8 x0 : 0000000000000032 [ 1.762539] Call trace: [ 1.765030] __cfi_check_fail+0x54/0x5c [ 1.768938] __cfi_check+0x5fa6c/0x66afc [ 1.772932] dwc2_init_params+0xd74/0xd78 [ 1.777012] dwc2_driver_probe+0x484/0x6ec [ 1.781180] platform_drv_probe+0xb4/0x100 [ 1.785350] really_probe+0x228/0x63c [ 1.789076] driver_probe_device+0x80/0xc0 [ 1.793247] __device_attach_driver+0x114/0x160 [ 1.797857] bus_for_each_drv+0xa8/0x128 [ 1.801851] __device_attach.llvm.14901095709067289134+0xc0/0x170 [ 1.808050] bus_probe_device+0x44/0x100 [ 1.812044] deferred_probe_work_func+0x78/0xb8 [ 1.816656] process_one_work+0x204/0x3c4 [ 1.820736] worker_thread+0x2f0/0x4c4 [ 1.824552] kthread+0x174/0x184 [ 1.827837] ret_from_fork+0x10/0x18 CFI validates that all indirect calls go to a function with the same exact function pointer prototype. In this case, dwc2_set_bcm_params is the target, which has a parameter of type 'struct dwc2_hsotg *', but it is being implicitly cast to have a parameter of type 'void *' because that is the set_params function pointer prototype. Make the function pointer protoype match the definitions so that there is no more violation. Fixes: 7de1debc ("usb: dwc2: Remove platform static params") Link: https://github.com/ClangBuiltLinux/linux/issues/1107 Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
