Put properties in order compatible, reg, interrupts, then anything else
the node has.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Sort the nodes according to the following rules:
* First, any overrides for properties or nodes created by included files,
  in the order they appeared in the include file.
* Second, any nodes with a reg property, in numerical order.
* Third, any nodes without a reg property, in alphabetical order of node
  name.

The second sorting rule at least will probably help if/when we need to
explicitly insert nodes for the various busses in Tegra; that will just
be an indentation change rather than also a node re-ordering.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

It's already specified in skeleton.dtsi, included via tegra20.dtsi.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Place each reg "entry" on its own line, and wrap the whole list in
<> rather than each individual entry.

The convention chosen here is slightly arbitrary, but is not consistent
throughout all Tegra files.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Ensure that all Tegraa GPIO specifiers contain a comment indicating which
GPIO name the number refers to.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

DT node names only need to include the unit address if it's required to
make the node name unique. Remove the unnecessary unit addresses.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Consistently don't place a space after < or before >.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Cardhu's eMMC controller is on sdhci@78000600, not sdhci@78000400.
Fix the typo. This roughly doubles the IO performance, since the
support-8bit property actually takes effect.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org # v3.4

Add device info for the core regulator tps62360 in tegra-cardhu
dts file.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed node name to reflect actual device type]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add a node for the Tegra30 SMMU

Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add a node for the Tegra20 GART

Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add Tegra MC(Memory Controller) nodes for tegra30.dtsi.

Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add Tegra MC(Memory Controller) nodes for tegra20.dtsi.

Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add AHB entry for tegra20/30.

Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

* Add node for the audio codec
* Enable Tegra's I2S1 controller and DAS
* Add node for top-level sound complex

Signed-off-by: Stephen Warren <swarren@nvidia.com>

This is the micro-SD card slot.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

According to the device's datasheet, it can support an interrupt too.
However, the existing board file doesn't specify an interrupt, and I
don't have the schematics, so I can't add an interrupts property. The
current Linux driver doesn't support anyway.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add the known i2c devices on seaboard to the i2c table.

Also rename the temperature sensor device node, and mark it as a nct1008
instead of an adt7461 (which it is -- the chips are compatible though).

Signed-off-by: Olof Johansson <olof@lixom.net>
[swarren: Removed isl29018 from patch; it's already there now. Fixed
 interrupts properties now that Tegra GPIO is an interrupt controller.
 Moved smart-battery to the correct I2C bus.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The I2C2 controller can be routed to either pingroup DDC or PTA. Seaboard
actually uses this as an I2C bus mux, and devices are connected to both
pingroups. This change statically assigns the I2C2 controller to pingroup
PTA, so that on-board devices can be accessed. The DDC pingroup is used
for EDID/DDC accesses which are not yet required, given the absence of
any Tegra graphics support. I2C muxing will be supported later.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

This I2C bus is used for EDID/DDC reads and other "slow" I2C devices.
This requires a 100KHz SCL (clock) rate.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add the device info for ALS and proximity sensor for tegra
boards cardhu, ventana and seaboard.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: s/PZ02/PZ2/ in .dts files, s/seabridge/seaboard/ in commit
 description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Ensure that the USB ULPI signals are not tri-stated, and have no pull-
up or pull-down.

Ensure that the pingroup hosting the USB ULPI reset signal (GPIO PV0 or
PV1 depending on the board, so UAC) is not tri-stated, and has no pull-
up or pull-down.

This change appears larger than it is due to the grouping and sorting of
the pin configuration data.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.

I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.

Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Not all boards use GPIO_PV0 as the ULPI PHY reset signal. Instead of
hard-coding this GPIO into devices.c, make the board files set it
explicitly. This will allow the PHY code to differentiate between set and
unset values, and hence know when to read the value from device tree.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

pll_p_out4 is used on all/most Tegra boards to drive the cdev2 output pin
to provide a reference clock to a ULPI USB PHY. This reference clock must
run at 24MHz, and the cdev2 output has no additional dividers.

Remove board-paz00.c's now-duplicate initialization of this clock.

Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Commit 40f9cf0 "ARM: tegra: reparent sclk to pll_c_out1" changed the
rate of hclk. Since pclk is derived from that, and only has integer
dividers, the pclk rate needs to change in the same fashion, from 54MHz
to 60MHz.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

pll_p_out4 needs to be used for other purposes. Reparent sclk so that
it runs from pll_c. Change sclk's rate to 120MHz from 108MHz since this
is the lowest precise rate that can be achieved by dividing the pll_c
rate without reducing the sclk rate. (600/5=120, 600/5.5=109.0909...,
600/6=100).

Signed-off-by: Stephen Warren <swarren@nvidia.com>

pll_c will be used as a clock source. Fill in tegra_pll_c_freq_table[]
so that it's possible to explicitly initialize the PLL.

NVIDIA's downstream nv-3.1 kernel and the ChromeOS kernel have different
pll_c tables. nv-3.1 contains entries for 522MHz and 598MHz output,
whereas the ChromeOS kernel contains entries for 600MHz output. I chose
to upstream the ChromeOS values for now, since the 600MHz rate appears
to match the default rate of this PLL when the HW boots, and it's not
clear to me why 522 or 598MHz are more useful.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[swarren: wrote commit description]

Add WM8903 codec nodes, and top-level sound complex node for basic
analog audio over headset jack and internal speakers.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Add nodes for the Tegra30 AHUB and I2S controllers.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Both the Tegra30 I2S and AHUB modules used clocks, and hence currently
require AUXDATA in order to get specific device names so that clock
lookups work.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Set up the audio clock tree for Tegra30 in an equivalent fashion to the
existing setup for Tegra20.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

pll_a uses pll_p_out1 as its parent. Therefore this clock needs to be
initialized to make sure pll_a has a known input clock. Failure to do so
will cause the system to crash early in the bootup.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The Tegra30 AHUB driver must call tegra_periph_reset_deassert() for all
devices on the AHUB's configlink bus. The AHUB driver must be able to
call clk_get_sys() to retrieve the clock parameter for this function.
Add the necessary clock aliases to allow this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>

Print an explicit error message in various failure cases to allow
easier diagnosis.

WARN_ON() some internal failures that users/clients shouldn't be able to
trigger.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

* Only provide debugfs-relates ops when CONFIG_DEBUG_FS is enabled.
* Implement pin_config_group_dbg_show op.
* Implement pin_config_config_dbg_show op.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Rather than having a single tegra-pinctrl driver that determines whether
it's running on Tegra20 or Tegra30, instead have separate drivers for
each that call into utility functions to implement the majority of the
driver. This change is based on review feedback of the SPEAr pinctrl
driver, which had originally copied to Tegra driver structure.

This requires that the two drivers have unique names. Update a couple
spots in arch/arm/mach-tegra for the name change.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>