- Mar 12, 2021
-
-
Douglas Anderson authored
This is a SKU variant of lazor. Add it. This squashes the downstream patches to support this hardware. NOTES: - The non-touch SKU actually has "innolux,n116bca-ea1" but that driver is still pending in simple-panel. The bindings have been Acked though [1]. Things work well enough with the "innolux,n116bge" timings for now, though. - The wonky special dts just for "-rev4" arguably doesn't need to go upstream since they weren't widely distributed, but since a few people have them we might as well. If it ever causes problems we can delete it. [1] https://lore.kernel.org/r/20210115144345.v2.4.I6889e21811df6adaff5c5b8a8c80fda0669ab3a5@changeid Cc: Stephen Boyd <swboyd@chromium.org> Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210301133318.v2.11.I556326b24441e22c8c429ce383cc157c7aaef44b@changeid Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org>
-
Matthias Kaehlcke authored
Lazor rev3 and later use the 'lite' version of the SC7180 SoC. Reviewed-by:
-
Abhishek Kumar authored
For trogdor, in the latest board-2.bin file, new BDF with variant name GO_LAZOR has been introduced, so we need this property set, for GO_LAZOR BDF to be picked. Cc: Philip Chen <philipchen@chromium.org> Signed-off-by:
Abhishek Kumar <kuabhs@chromium.org> [dianders: adjusted subject line and sort order] Signed-off-by:
-
Venkata Lakshmi Narayana Gubba authored
Removed voting for RPMH_RF_CLK2 which is not required as it is getting managed by BT SoC through SW_CTRL line. Cc: Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org> Signed-off-by:
-
Alexandru M Stan authored
Removed the pinctrl and pin{mux,conf} for the control pins because: 1. The only need for them is for userspace control via flash_fp_mcu 2. cros-ec doesn't know what to do with them, and even if it did, it would interfere with flash_fp_mcu at the most inopportune times Since we're not using hogs, we rely on AP firmware to set all the control pins correctly. Reviewed-by:Alexandru M Stan <amstan@chromium.org> [dianders: adjusted since coachz isn't upstream yet] Reviewed-by; Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
-
Stephen Boyd authored
We only want to use this clk driver on CoachZ devices. Disable it for all other Trogdor boards. NOTE: CoachZ devices aren't yet supported upstream so until it is this is just disabled for all trogdor. Cc: Tomasz Figa <tfiga@chromium.org> Signed-off-by:
-
Stephen Boyd authored
Configure the pen to be a wakeup source only when the pen is ejected instead of both when the pen is ejected and inserted. This corresponds to wake source requirements. Signed-off-by:
-
Douglas Anderson authored
Let's avoid a bit of duplication by pushing this up to the trogdor.dtsi file. Suggested-by:
-
Douglas Anderson authored
The trackpad interrupt got renamed and also moved to a new GPIO on newer boards. Let's do the move in the "trogdor.dtsi" file and then undo it in the two old boards. NOTE: since none of the new boards have device trees yet, this change looks silly on its own but it will make sense after more boards are supported. Signed-off-by:
-
Douglas Anderson authored
In general pinconf belongs in board files, not SoC files. Move it to the only current user (trogdor). Also adjust the drive strengths and pulls. Cc: V Sujith Kumar Reddy <vsujithk@codeaurora.org> Cc: Srinivasa Rao Mandadapu <srivasam@codeaurora.org> Cc: Tzung-Bi Shih <tzungbi@chromium.org> Cc: Judy Hsiao <judyhsiao@chromium.org> Signed-off-by:
-
Stephen Boyd authored
Drop the old node and add the new one in its place. Cc: Stephen Boyd <swboyd@chromium.org> Cc: Jeykumar Sankaran <jsanka@codeaurora.org> Cc: Chandan Uddaraju <chandanu@codeaurora.org> Cc: Vara Reddy <varar@codeaurora.org> Cc: Tanmay Shah <tanmay@codeaurora.org> Cc: Rob Clark <robdclark@chromium.org> Signed-off-by:
-
Vinod Koul authored
Add cpufreq node and reference it for the CPUs. Signed-off-by:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20210216111703.1838663-1-vkoul@kernel.org Signed-off-by:
-
Vinod Koul authored
Now that we have GCC define, use the enums instead of numbers in the DTS Signed-off-by:
-
Vinod Koul authored
This enabled the four remoteprocs found in SM8350, audio, compute, modem and sensor for MTP platform and adds firmware for them. Signed-off-by:
-
Vinod Koul authored
Add remoteproc nodes for the audio, compute and sensor cores, define glink for each one. Signed-off-by:
-
Vinod Koul authored
SMP2P is used for interrupting and being interrupted about remoteproc state changes related to the audio, compute, modem and sensor subsystems. Signed-off-by:
-
Vinod Koul authored
Add the rmtfs as a reserved memory node. Signed-off-by:
-
Vinod Koul authored
This adds RPMH power domain found in SM8350 SoC Signed-off-by:
-
Vinod Koul authored
Fix the typo s/Limaited/Limited Signed-off-by:
-
Vinod Koul authored
Add the property "regulator-names" to the regulators as given in schematics so that it is easier to understand the regulators being used Signed-off-by:
-
Vinod Koul authored
Enabled the UFS node found in SM8350-MTP platform, also add the regulators associated with UFS HC and UFS phy to these nodes. Signed-off-by:
-
Vinod Koul authored
This adds UFS HC and UFS phy nodes to the SM8350 DTS Signed-off-by:
-
Jack Pham authored
Enable both USB controllers and associated hsphy and qmp phy nodes on sm8350 MTP. Designate the usb_1 instance as peripheral-mode only until proper PMIC based Type-C dual-role handling is supported. TODO: the second USB controller is exposed to a microAB port. Dual- role can be supported for this by adding the "usb-role-switch" property as well as defining a USB connector node with a "gpio-usb-b-connector" compatible. However, this requires GPIO support from PM8350 which is still missing. Signed-off-by:
Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210116013802.1609-3-jackp@codeaurora.org Signed-off-by:
-
Jack Pham authored
Add device nodes for the two instances each of USB3 controllers, QMP SS PHYs and SNPS HS PHYs. Signed-off-by:
-
Vinod Koul authored
This adds apss_smmu node to SM8350 DTS Signed-off-by:
-
Sai Prakash Ranjan authored
ARM architected timer interrupts DT property specifies EL2/HYP physical interrupt and not EL2/HYP virtual interrupt for the 4th interrupt property. As per interrupt documentation for SM8250 SoC, the EL2/HYP physical timer interrupt is 10 and EL2/HYP virtual timer interrupt is 12, so fix the 4th timer interrupt to be EL2 physical timer interrupt (10 in this case). Fixes: 60378f1a ("arm64: dts: qcom: sm8250: Add sm8250 dts file") Signed-off-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Link: https://lore.kernel.org/r/744e58f725d279eb2b049a7da42b0f09189f4054.1613468366.git.saiprakash.ranjan@codeaurora.org Signed-off-by:
-
Sai Prakash Ranjan authored
As per interrupt documentation for SM8350 SoC, the polarity for level triggered PMU interrupt is low, fix this. Fixes: b7e8f433 ("arm64: dts: qcom: Add basic devicetree support for SM8350 SoC") Signed-off-by:
-
Sai Prakash Ranjan authored
As per interrupt documentation for SM8250 SoC, the polarity for level triggered PMU interrupt is low, fix this. Fixes: 60378f1a ("arm64: dts: qcom: sm8250: Add sm8250 dts file") Signed-off-by:
-
Sai Prakash Ranjan authored
Use the generic DT node name "power-controller" for AOSS message ram instead of the protocol name QMP(Qualcomm Messaging Protocol) since it is used for power management requests. Reviewed-by:
-
Sai Prakash Ranjan authored
Use the generic DT node name "power-controller" for AOSS message ram instead of the protocol name QMP(Qualcomm Messaging Protocol) since it is used for power management requests. Reviewed-by:
-
Sai Prakash Ranjan authored
Use the generic DT node name "power-controller" for AOSS message ram instead of the protocol name QMP(Qualcomm Messaging Protocol) since it is used for power management requests. Reviewed-by:
-
Sai Prakash Ranjan authored
Use the generic DT node name "power-controller" for AOSS message ram instead of the protocol name QMP(Qualcomm Messaging Protocol) since it is used for power management requests. Reviewed-by:
-
Matthias Kaehlcke authored
On trogdor the ADC thermal monitor is used for monitoring certain device temperatures. All trogdor boards have at least a thermistor for the charger temperature, optionally they may have others. Currently the ADC thermal monitor is configured to use channel 1 for the charger temperature. Given that all trogdor boards have the charger thermistor it makes more sense to use channel 0, and then let boards with other thermistors use channels 1, 2, 3, rather than 0, 2, 3. Reviewed-by:
-
Matthias Kaehlcke authored
The trip point configuration of the charger thermal zone for trogdor is missing a node for the critical trip point. Add the missing node. Reviewed-by:
-
Matthias Kaehlcke authored
Lazor is stuffed with a 47k NTC as thermistor for the charger temperature which currently isn't supported by the PM6150 ADC driver. Disable the charger thermal zone to avoid the use of bogus temperature values. Reviewed-by:
-
Matthias Kaehlcke authored
Some revisions of trogdor boards use a thermistor for the charger temperature which currently isn't supported by the PM6150 ADC driver. This results in bogus temperature readings. Add a label to the charger thermal zone to facilitate disabling of the thermal zone on affected boards. Signed-off-by:
-
- Mar 06, 2021
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdmaLinus Torvalds authored
Pull rdma fixes from Jason Gunthorpe: "Nothing special here, though Bob's regression fixes for rxe would have made it before the rc cycle had there not been such strong winter weather! - Fix corner cases in the rxe reference counting cleanup that are causing regressions in blktests for SRP - Two kdoc fixes so W=1 is clean - Missing error return in error unwind for mlx5 - Wrong lock type nesting in IB CM" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: RDMA/rxe: Fix errant WARN_ONCE in rxe_completer() RDMA/rxe: Fix extra deref in rxe_rcv_mcast_pkt() RDMA/rxe: Fix missed IB reference counting in loopback RDMA/uverbs: Fix kernel-doc warning of _uverbs_alloc RDMA/mlx5: Set correct kernel-doc identifier IB/mlx5: Add missing error code RDMA/rxe: Fix missing kconfig dependency on CRYPTO RDMA/cm: Fix IRQ restore in ib_send_cm_sidr_rep -
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds authored
Pull gcc-plugins fixes from Kees Cook: "Tiny gcc-plugin fixes for v5.12-rc2. These issues are small but have been reported a couple times now by static analyzers, so best to get them fixed to reduce the noise. :) - Fix coding style issues (Jason Yan)" * tag 'gcc-plugins-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: gcc-plugins: latent_entropy: remove unneeded semicolon gcc-plugins: structleak: remove unneeded variable 'ret'
-
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds authored
Pull pstore fixes from Kees Cook: - Rate-limit ECC warnings (Dmitry Osipenko) - Fix error path check for NULL (Tetsuo Handa) * tag 'pstore-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: pstore/ram: Rate-limit "uncorrectable error in header" message pstore: Fix warning in pstore_kill_sb()
-
