Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.

This patch adds flushes in:

	intel_enable_plane
	gen6_init_clock_gating
	ivybridge_init_clock_gating

Signed-off-by: Keith Packard <keithp@keithp.com>

After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch.  On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.

v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes.  This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.

Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit 885a5014

.

We actually *do* need to track DPMS state so that on hotplug, we don't
retrain the link until DPMS is disabled.

However, that code had avery small bug -- it wouldn't set the
dpms_mode at mode set time, and so link retraining would not actually
occur on monitor hotplug until the monitor had gone through a DPMS
off/DPMS on cycle.

Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>

Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.

This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).

Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port

Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>

Eliminates an open-coded read and also gains the retry behaviour of
intel_dp_get_dpcd, which seems like a good idea.

Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>

This describes the function better, allowing it to be used where the
DPCD value is relevant.

Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>

This uses the common dpcd reading routine, i915_dp_detect_common,
instead of open-coding a call to intel_dp_aux_native_read. Besides
reducing duplicated code, this also gains the read retries which
may be necessary when a cable is first plugged back in and the link
needs to be retrained.

Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>

drm_helper_hpd_irq_event queues another work proc to go and deliver
the user-space event, and that function also wants to hold the config
mutex, so we shouldn't hold the mutex across the
drm_helper_hpd_irq_event call.

Signed-off-by: Keith Packard <keithp@keithp.com>

The docs say the port has to come on in training pattern 1; at this
point, though, ->DP is in normal mode.  The intent here is to wait
until the port is in fact sending data, but that doesn't happen since
we've broken the sequence the hardware expects, and the vblank wait will
time out and kvetch in the log.

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

The DP spec says training patterns 1 and 2 are to be sent non-scrambled,
and the GPU docs claim that happens (or at least, there's no explicit
scrambling control).  But the sink may be confused if we don't
explicitly tell it what we're doing, so play it safe.

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

Consider a 1600x900 panel, upscaling a 1360x768 mode, full-aspect.  The
old math would give you:

    scaled_width  = 1600 * 768;         /* 1228800 */
    scaled_height = 1360 * 900;         /* 1224000 */
    if (scaled_width > scaled_height) { /* pillarbox, and true */
        width  = 1224000 / 768;         /* int(1593.75) = 1593 */
        x      = (1600 - 1593 + 1) / 2; /* 4 */
        y      = 0;
        height = 768;
    } /* ... */

This is broken.  The total width of scanout would then be 1593 + 4 + 4,
or 1601, which is wider than the panel itself.  The hardware very
dutifully implements this, and you end up with a black 45° diagonal from
the top-left corner to the bottom edge of the screen.  It's a cool
effect and all, but not what you wanted.  Similar things happen for the
letterbox case.

The problem is that you have an integer number of pixels, which means
it's usually impossible to upscale equally on both axes.  1360/768 is
1.7708, 1600/900 is 1.7777.  Since we're constrained on the one axis,
the other one wants to come out as an even number of pixels (the panel
is almost certainly even on both axes, and the x/y offsets will be
applied on both sides).  In the math above, if 'width' comes out even,
rounding down is correct; if it's odd, you'd rather round up.  So just
increment width/height in those cases.

Tested on a Lenovo T500 (Ironlake).

Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-By: Daniel Manrique <daniel.manrique@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38851


Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>

Hotplug detection is a mode setting operation and must hold the
struct_mutex or risk colliding with other mode setting operations.

In particular, the display port hotplug function attempts to re-train
the link if the monitor is supposed to be running when plugged back
in. If that happens while mode setting is underway, the link will get
scrambled, leaving it in an inconsistent state.

This is a special case -- usually the driver mode setting entry points
are covered by the upper level DRM code, but in this case the function
is invoked as a work function not under the control of DRM.

Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

It's not clear what a sink would do if you wrote zero to this register -
which I guess would mean "I don't support any channel encodings, good
luck" - but let's not find out.

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

%hx alone prints 0 as "0", not "00".

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

For parity with radeon and nouveau, and also because I suspect we're
going to need it to get format-conversion dongles right.

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

No reason not to see this on g4x, after all.

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Per the specs and to address
https://bugs.freedesktop.org/show_bug.cgi?id=36888

.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>

Physically-addressed hardware status pages are initialized early in
the driver load process by i915_init_phys_hws. For UMS environments,
the ring structure is not initialized until the X server starts. At
that point, the entire ring structure is re-initialized with all new
values. Any values set in the ring structure (including
ring->status_page.page_addr) will be lost when the ring is
re-initialized.

This patch moves the initialization of the status_page.page_addr value
to intel_render_ring_init_dri.

Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org

Because of a typo, calling ioctl with DRM_IOCTL_I915_OVERLAY_PUT_IMAGE
is broken if the macro is used directly. When using libdrm the bug is
not hit, since libdrm handles the ioctl encoding internally.

The typo also leads to the .cmd and .cmd_drv fields of the drm_ioctl
structure for DRM_I915_OVERLAY_PUT_IMAGE having inconsistent content.

Signed-off-by: Ole Henrik Jahren <olehenja@alumni.ntnu.no>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>

Failing to pin a scanout buffer will most likely lead to a black
screen, so if the GPU is wedged, then just let the pin happen and hope
that things work out OK.

v2: Just ignore any error from i915_gem_object_wait_rendering, as
suggested by Chris Wilson

Signed-off-by: Keith Packard <keithp@keithp.com>

If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode.  So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  sparc,kgdbts: fix compile regression with kgdb test suite

Commit 63ab25eb

 (kgdbts: unify/generalize gdb breakpoint adjustment)
introduced a compile regression on sparc.

kgdbts.c: In function 'check_and_rewind_pc':
kgdbts.c:307: error: implicit declaration of function 'instruction_pointer_set'

Simply add the correct macro definition for instruction pointer on the
Sparc architecture.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  CIFS: Fix wrong length in cifs_iovec_read

Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Make Dell Latitude E6420 use reboot=pci
  x86: Make Dell Latitude E5420 use reboot=pci

Yet another variant of the Dell Latitude series which requires
reboot=pci.

From the E5420 bug report by Daniel J Blueman:

> The E6420 is affected also (same platform, different casing and
> features), which provides an external confirmation of the issue; I can
> submit a patch for that later or include it if you prefer:
> http://linux.koolsolutions.com/2009/08/04/howto-fix-linux-hangfreeze-during-reboots-and-restarts/



Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>

Rebooting on the Dell E5420 often hangs with the keyboard or ACPI
methods, but is reliable via the PCI method.

[ hpa: this was deferred because we believed for a long time that the
  recent reshuffling of the boot priorities in commit
  660e34ce

 fixed this platform.
  Unfortunately that turned out to be incorrect. ]

Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Link: http://lkml.kernel.org/r/1305248699-2347-1-git-send-email-daniel.blueman@gmail.com


Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Fix unfenced alignment on pre-G33 hardware
  drm/i915: Add quirk to disable SSC on Lenovo U160 LVDS

It seems to hurt performance in real life.  Yes, the inode will be used
later, but the conditional doesn't seem to predict all that well
(negative dentries are not uncommon) and it looks like the cost of
prefetching is simply higher than depending on the cache doing the right
thing.

As usual.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The compiler, at least for ix86 and m68k, validly warns that the
comparison:

	next <= (loff_t)-1

is always true (and it's always true also for x86-64 and probably all
other arches - as long as pgoff_t isn't wider than loff_t).  The
intention appears to be to avoid wrapping of "next", so rather than
eliminating the pointless comparison, fix the loop to indeed get exited
when "next" would otherwise wrap.

On m68k the following warning is observed:

  fs/fscache/page.c: In function '__fscache_uncache_all_inode_pages':
  fs/fscache/page.c:979: warning: comparison is always false due to limited range of data type

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Suresh Jayaraman <sjayaraman@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>