This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This caused issues with tracing as it's longer than
the buffer size used there.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This module parameter isn't and won't be used. So ignore
its value and set BT_CH_ANNOUNCE unconditionally.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The BCM5354 SoC has a build in ieee80211 core rev 13 with a LP-PHY on
it. This devices has a sprom version 3 stored in the nvram. This patch
removes the warning and uses the opo values from the sprom as mentioned
in the specs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These attributes should be in the sprom for rev 2 and 3, but they were
not read out.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was done accordingly to new specs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With this patch the same registers are written, but this access is now
protected by a lock.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using that IDs we can write workarounds for various cards

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, default VHT configuration from the firmware is used
for the VHT operations. Adding vhtcfg command to configure the
firmware based on input received from cfg.

Enable VHT for AP mode only when cfg80211_ap_settings has a
VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add proper alignment at first packet copy, to avoid extra copies made later
in networking stack.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move processing of received packets to tasklet from hard-irq context.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

RX path has extra copying of packets, that can be avoided.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use dedicated DMA coherent buffers for RX urbs, to avoid allocation of large
skbuffs in hard-irq context and improve performance.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels.  In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.

Move handling code into the irq thread function to avoid that.

Reported-by: Gregoire Gentil <gregoire@alwaysinnovating.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

We were printing out all the hex dumps regardless of whether dynamic
debugging was enabled or not.  Now that print_hex_dump_debug() has
been implemented, we can use that instead.

Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Don't ignore dummy packets when our queues are empty. This causes dummy
packets never to be sent when traffic is not suspended by FW thresholds,
which happens only in high Tx throughput situations. This may hurt Rx
performance.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Print board type, PG with metal and ROM versions.
This might help debugging HW related issues.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the
locking using assert_spin_locked, which is written to behave correctly
in all cases.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

report the average beacon rssi which is calculated
by firmware for roaming statistics instead of the
last rx packet rssi. this results a more accurate
rssi reporting

Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Accumulate the total number of sent packets per-link to find out how far
the encryption sequence number has progressed. Use this number as the
initial security sequence number after recovery.

This consolidates security sequence handling for both chip families, as
we no longer have to rely on 12xx specific Tx completion.

A fortunate side effect of this is correct management of seq numbers for
AP roles and multi-role scenarios.

When a link is removed we save the last seq number on a persistent part
of the wlvif. This helps the data survive through recoveries/suspends,
which also entail changes in the hlid of the link.

This functionality is STA only currently.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The HLID of a STA can change, particularly during recovery. Don't cache
the HLID before it was potentially allocated.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

commit 144614f3eebd7d only allowed a single active link when
turning on the optimization, ignoring the fact that an AP has two
additional global links.
Use 3 links as an indication for a single active link. Use the
FW PSM bits to verify the extra active link belongs to the AP role.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Maximum number of supported RX BA sessions depends on chip type.
wl18xx supports 5 RX BA sessions while wl12xx supports 3.

Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

It is requiered to enter sleep mode with smaller delay in forced PS mode.
This fixes issue of testing force PS mode during VoIP traffic where packets
are sent every 20ms. Chip never enters ps mode with default 30 ms delay
in such test.

Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Schedule different time event based on the ROC type

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>