The index of se should be 127. And the previous clock index was 125. So
we need to set up the index for se to get the correct index between se
to sata_cold.

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Use functional name for DT entry instead of h/w name.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Use functional name for DT entry instead of h/w name.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

No Tegra30 Platform is running PLL_P at another rate than 408MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

This adds the device tree for the Toradex Iris carrier board used
together with a Colibri T20 512MB COM.

The Iris has the following features, in brackets the current status:
- DVI and VGA output through DVI-I connector (DVI-D enabled and tested)
- LVDS output
- 1 USB host port (enabled and tested)
- 1 USB OTG port (enabled)
- 100 MBit Ethernet (enabled and tested)
- 5 UART ports  (2 on 10way headers enabled and tested)
- 1 MicroSD Slot (enabled and tested)
- Audio connectors (enabled, only HP out and Line-in tested)
- i2c RTC
- GPIO connector (enabled, only sparsely tested)
- external i2c bus
- 4 PWM out
- analog in

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This adds the device tree include file for the Toradex Colibri T20
Computer on Module (COM). It's only valid for the 512MB RAM version of
the module, as the 256MB version needs different EMC tables and flash
configuration. To make this clear the suffix -512 was added to the board
compatible string.

The Colibri T20 uses a Tegra20 SoC and has onboard USB Ethernet and AC97
sound.

Still some things like onboard NAND support missing, but should be a
good base for further development.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

No Tegra20 Platform is running PLL_P at another rate than 216MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable Tegra based keyboard interfacing for keys and provide
all key mapping through DTS file.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable Tegra based keyboard controller and populate the key mapping
for Whistler.

With this patch, HOME, BACK, POWER and MENU keys will work.
Still other keys which are in ROW3 and ROW4 will not work as it
conflicts with KBC pins on SDIO2 pinmux.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

UARTC is used for the interfacing with bluetooth device.
Register this UART channel as high speed serial channel
so that it can use the APB DMA for data transfer.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Enable Tegra based keyboard controller and populate the key matrix for
seaboard. The key matrix was originally on driver code which is removed
to have clean driver. The key mapping is now passed through dts file.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

NVIDIA's Tegra SoCs have the matrix keyboard controller which
supports 16x8 type of matrix. The number of rows and columns
are configurable.

Add DT entry for KBC controller.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: added clocks property]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This ensures nodes are sorted in order of reg address. This makes it
easier to compare against e.g. the U-Boot device trees, and is simply
consistent and clean.

While we're at it, remove the unit address from the cache-controller
node name, since it's unique without it.

Reported-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add default entry for the AC97 host controller.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This patch adds support for Tegra30 Beaver board in upstream kernel.

Beaver board is a Tegra30 SoC based development board, it has
following features:
 - T30 or T33 SoC (Qual core ARM Cortex A9)
 - 2 GB DDR3L
 - 16 GB EMMC
 - 1 SD slot
 - 1 USB Standart A port and 1 USB micro AB port
 - PCI-E Gig Ethernet
 - Audio input/output
 - SATA port
 - HDMI output
 - UART and JTAG

Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The compatible properties of Tegra SoC based boards or machines need
to be documented. This patch adds these board levle compatible
properties into device tree binding document.

Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Signed-off-by: Stephen Warren <swarren@nvidia.com>

Signed-off-by: Stephen Warren <swarren@nvidia.com>

Signed-off-by: Stephen Warren <swarren@nvidia.com>

... and disable tri-state from the pingroup that contains the poweroff
GPIO.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

Use engineering name 'Tegra20' instead of 'Tegra2'

Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add APB DMA requestor and serial aliases for serial controller.
There will be two serial driver i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.

The simple serial driver get enabled with compatible nvidia,tegra20-uart
and APB DMA based driver will get enabled with compatible
nvidia,tegra20-hsuart.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

tegra30 gpio controller is not compatible with the tegra20 due to
their bank stride i.e. Tegra20 bank stride is 0x80 where Tegra30
bank stride is 0x100.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed typo syntax error]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add new Tegra 114 SoC support.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add a new evaluation board, Pluto for Tegra 114 family.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add a new evaluation board, Dalmore for Tegra 114 family.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Initial support for Tegra 114 SoC. This is expected to be included in
the board DTS files, Tegra 114 SoC based evaluation board family.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add tegra_chip_id TEGRA114 0x35

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Conflicts:
	arch/arm/mach-tegra/platsmp.c

The "powered-down" cpuidle mode of Tegra20 needs the CPU0 be the last one
core to go into this mode before other core. The coupled cpuidle framework
can help to sync the MPCore to coupled state then go into "powered-down"
idle mode together. The driver can just assume the MPCore come into
"powered-down" mode at the same time. No need to take care if the CPU_0
goes into this mode along and only can put it into safe idle mode (WFI).

The powered-down state of Tegra20 requires power gating both CPU cores.
When the secondary CPU requests to enter powered-down state, it saves
its own contexts and then enters WFI for waiting CPU0 in the same state.
When the CPU0 requests powered-down state, it attempts to put the secondary
CPU into reset to prevent it from waking up. Then power down both CPUs
together and power off the cpu rail.

Be aware of that, you may see the legacy power state "LP2" in the code
which is exactly the same meaning of "CPU power down".

Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The flow controller can help CPU to go into suspend mode (powered-down
state). When CPU go into powered-down state, it needs some careful
settings before getting into and after leaving. The enter and exit
functions do that by configuring appropriate mode for flow controller.

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Implementing suspend, resume and rail_off_ready API for tegra_cpu_car_ops. These
functions were used for CPU powered-down state maintenance.

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The powered-down state of Tegra20 requires power gating both CPU cores.
When the secondary CPU requests to enter powered-down state, it saves
its own contexts and then enters WFI. The Tegra20 had a limition to
power down both CPU cores. The secondary CPU must waits for CPU0 in
powered-down state too. If the secondary CPU be woken up before CPU0
entering powered-down state, then it needs to restore its CPU states
and waits for next chance.

Be aware of that, you may see the legacy power state "LP2" in the code
which is exactly the same meaning of "CPU power down".

Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The "powered-down" CPU idle mode of Tegra cut off the vdd_cpu rail, it
include the power of GIC. That caused the SGI (Software Generated
Interrupt) been lost. Because the SGI can't wake up the CPU that in
the "powered-down" CPU idle mode. We need to check if there is any
pending SGI when go into "powered-down" CPU idle mode. This is important
especially when applying the coupled cpuidle framework into "power-down"
cpuidle dirver. Because the coupled cpuidle framework may have the
chance that misses IPI_SINGLE_FUNC handling sometimes.

For the PPI or SPI, something like the legacy peripheral interrupt. It
still can be maintained by Tegra legacy interrupt controller. If there
is any pending PPI or SPI when CPU in "powered-down" CPU idle mode. The
CPU can be woken up immediately. So we don't need to take care the same
situation for PPI or SPI.

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Clock "emc" is for the External Memory Controller. The USB driver has no
business touching this clock directly. Remove the code that does so.

Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

As Tegra PHY driver needs to access one of the host registers,
added few APIs.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[swarren: moved assignment of phy->is_ulpi_phy to previous patch.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Tegra20 USB has 3 PHY instances:
Instance 1 and 3 are UTMI. Instance 2 is ULPI.

As instance number was used to differentiate ULPI from UTMI,
used DT param to get this info and processed accordingly.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[swarren: moved assignment of phy->is_ulpi_phy into this patch out
of next patch.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Tegra20 USB has 3 PHY instances. Instance 0 is based on
legacy PHY interface and other two are standard interfaces.

As instance number was used to differentiate legacy from
standard interfaces, used DT param to get this info and
processed accordingly.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The patch to add USB PHY nodes to device tree was written before Tegra
supported the clocks property in device tree. Now that it does, add the
required clocks properties to these nodes.

This will allow all clk_get_sys() calls in tegra_usb_phy.c to be replaced
by clk_get(phy->dev, clock_name), as part of converting the PHY driver to
a platform driver.

Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add DT nodes for Tegra USB PHY along with related documentation.
Also added a phandle property to controller DT node, for referring
to connected PHY instance.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>