* Initialize rq->cmd_type in ide_wait_cmd(), ide_cmd_ioctl() and
  set_pio_mode() (other callers were aleady over-riding rq->cmd_type).

* Remove no longer needed rq->cmd_type setup from ide_init_drive_cmd().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use wait_drive_not_busy() in drive_cmd_intr().

v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests.  Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set.  Also,
ide_dma_intr() is modified to use task_end_request().

Enables TASKFILE ioctls to get valid register outputs on
successful completion.

Bart:
- ported it over recent IDE changes

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.

* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.

* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Check for DRQ bit being cleared on the final status check.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_dump_status() may set HOB bit before ide_end_drive_cmd() is called.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

In ide_taskfile_ioctl(), there was a race condition involving
drive->io_32bit.  It was cleared and restored during ioctl
requests but there was no synchronization with other requests.
So, other requests could execute with the altered ->io_32bit
setting or updated drive->io_32bit could be overwritten by
ide_taskfile_ioctl().

This patch adds IDE_TFLAG_IO_16BIT flag to indicate to
ide_pio_datablock() that 16-bit I/O is needed regardless of
drive->io_32bit settting.

Bart:
- ported it over recent IDE changes

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This belongs to user-space (and only if really needed).

   text    data     bss     dec     hex filename
   3874     180      28    4082     ff2 drivers/ide/pci/cmd64x.o.before
   2231     180       0    2411     96b drivers/ide/pci/cmd64x.o.after

Additionaly to being bloat the code reported incorrect UDMA modes for
the reserved values of UDIDETCR0/1 registers.

Also while at it remove unused CNTRL_DIS_RA0/1 defines.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
  results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
  (including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
  x86 machines using user-space solutions or dm-byteswap should result in
  much better performance because DMA can be used)

For previous discussions please see:

http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.html
http://lkml.org/lkml/2004/2/28/111



[ I have dm-byteswap device mapper target if somebody is interested
  (patch is for 2.6.4 though but I'll dust it off if needed). ]

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_busy_sleep() helper and use it in do_probe(),
enable_nest() and probe_hwif().

As a nice side-effect this fixes a minor bug in do_probe()
(the code was reading status register without any delay).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Print banner message once per controller in m68k host drivers.

* Change printk() level to KERN_INFO in buddha, falconide and gayle.

* Add banner message to q40ide.

This is basically a preparation for the future IDE layer changes.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move setting hwif->sg_max_nents from pmac_ide_setup_device()
to pmac_ide_setup_dma().

Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move setting hwif->gendev.parent from ide_pci_setup_ports()
  to ide_hwif_configure().

* Always set hwif->io_ports in ide_hwif_configure().

* Use ide_init_port_hw() in ide_hwif_configure().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* ide_init_hwif_ports() call in setup-pci.c::ide_hwif_configure()
  doesn't depend on the default cotrol register offset, default IRQ
  or ppc_ide_md.ide_init_hwif implementations so ide_std_init_ports()
  can always be used.

* Since 'base' is always non-zero and thus hwif->io_ports[IDE_DATA_OFFSET]
  is also non-zero always clear hwif->noprobe.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* hwif->hold is always set in au_ide_probe() (few lines earlier),
  no need to set it again

* hwif->{channel,select_data,config_data} should be always zero

* autotune PIO also if CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA is defined

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
  file for probing PCI host drivers registered with IDE core (special case
  for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
  the ordering in which all IDE host drivers are probed when IDE is built-in
  during link time.

* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
  specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
  arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).

* Move probing of ide-cris (cris arch specific) host driver before cmd640
  (x86 arch specific).

* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
  on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
  (h8300 arch specific).

* Add "probe_vlb" kernel parameter to cmd640 host driver and update
  Documentation/ide.txt accordingly.

* Make IDE_ARM config option visible so it can also be disabled if needed.

* Remove bogus comment from ide.c while at it.

v2:
* Fix two issues spotted by Sergei:
  - replace ENOMEM error value by ENOENT in ide-h8300 host driver
  - fix MODULE_PARM_DESC() in cmd640 host driver

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add mpc8xx_ide_probe() to mpc8xx.c and call it from probe_for_hwifs().

* Convert ide_arm, ide-cris, ide-h8300, ide-pnp, buddha, falconide, gayle,
  macide, q40ide, cmd640 and mpc8xx host drivers to use ide_device_add().

  This removes dependency on ide_generic for these drivers so update
  ide/Kconfig accordingly.

v2:
* ide_arm build fix (s/ide_device_idx/ide_device_add/)
  (Thanks to Christoph Lameter <clameter@sgi.com> for reporting the problem).

Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make BLK_DEV_CMD640 select IDE_GENERIC.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_init_port_data() call from ide_arm_init() and move
  ide_arm_init() call from init_ide_data() to ide_init().

This patch is a preparation for the future changes (and as a side-effect
makes obsolete "idex=io[,ctl[,irq]]" kernel parameters work for ide_arm).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename init_hwif_data() to ide_init_port_data() and export it.

* For all users of ide_register_hw() with 'initializing' argument set
  hwif->present and hwif->hold are always zero so convert these host
  drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
  instead (also no need for init_hwif_default() call since the setup
  done by it gets over-ridden by ide_init_port_hw() call).

* Drop 'initializing' argument from ide_register_hw().

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_init_port_hw() helper.

* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
  and use ide_init_port_hw().

* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
  and use ide_init_port_hw().

* sgiioc4.c: use ide_init_port_hw().

* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
  setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
  in pmac_ide_setup_device().

This patch is a preparation for the future changes in the IDE probing code.

There should be no functionality changes caused by this patch.

Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

'if (hwif->io_ports[IDE_DATA_OFFSET] != cmd_base)' is always true.

Cc: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix build break of powerpc holly_defconfig:

In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)

There's no need to have a sized array in the prototype, might as well
turn it into a pointer.

It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.

Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename ide_device_add() to ide_device_add_all() and make it accept
  'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.

* Add ide_device_add() wrapper for ide_device_add_all().

* Convert ide_generic_init() to use ide_device_add_all().

* Remove no longer needed ideprobe_init().

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add hwif->chipset fixup identical to the one in ideprobe_init()
to ide_device_add().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hwif->chipset should be set if the hwif is claimed by host driver.

Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hwif->chipset should be set if the hwif is claimed by host driver.

Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

After hwif_register_devices() IDE devices are ready to be used so
the way in which ide_device_add() works currently is racy for hosts
with serialized / IRQ sharing interfaces.

Fix ide_device_add() by looping over interfaces for probe_hwif(),
hwif_init() and hwif_register_devices() operations.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Host drivers using ide_register_hw() and 'initializing == 1':

* ide-pnp
  - depends on ISA

* ide_arm 
  - ARM arch specific
  - initialized before all other host drivers

* ide-cris
  - CRIS arch specific => IDE_ARCH_OBSOLETE_INIT is not defined
  - broken

* ide-h8300
  - H8300 arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI

* buddha/q40/gayle/macide/falconide
  - M68K arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI

Since the only host drivers which probe interfaces before the above ones are:

* ali14xx/dtc2278/ht6560b/qd65xx/umc8672
  - depend on ISA
  - require IDE_ARCH_OBSOLETE_INIT=y to work

* PCI ones
  - depend on PCI

don't try to unregister interfaces if 'initializing == 1' in ide_register_hw()
(it is possible that built-in host drivers will claim all IDE interfaces but
later ide-pnp host driver will try to unregister them - this change fixes it).

Also skip hwif->hold check if 'initializing == 1' since it is set only by:

* pmac
  - PPC && PMAC specific => no ISA

* au1xxx-ide
  - MIPS && SOC_AU1200 specific => no ISA

and use ide_find_port() helper to find free ide_hwifs[] slot.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Assign drive->quirk_list in ->quirkproc implementations:
  - hpt366.c::hpt3xx_quirkproc()
  - pdc202xx_new.c::pdcnew_quirkproc()
  - pdc202xx_old.c::pdc202xx_quirkproc()

* Make ->quirkproc void.

* Move calling ->quirkproc from do_identify() to probe_hwif().

* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.

* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
  no longer needed drive->present check from is_dev_seagate_sata().

* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
  as an argument.  Then convert ide_register_hw() to accept 'quirkproc'
  argument instead of 'fixup' one.

* Remove no longer needed ->fixup method.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>