- Aug 05, 2019
-
-
Martyn Welch authored
Document the ON Semiconductor NOA1305 ambient light sensor devicetree bindings. Signed-off-by:
Martyn Welch <martyn.welch@collabora.com> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Denis Ciocca authored
Not even sure why it was there since the beginning. Just use IRQ number in the sensor_data struct. Signed-off-by:
Denis Ciocca <denis.ciocca@st.com> Signed-off-by:
-
Martin Kepplinger authored
in_accel_x_scale, in_accel_y_scale and in_accel_z_scale are always the same. The scale is still defined to be in "info_mask_separate". Userspace (iio-sensor-proxy and others) is not used to that and only looks for "in_accel_scale" for the scaling factor to apply. Change IIO_CHAN_INFO_SCALE from being separate in all channel to be shared by type. This removes in_accel_x_scale, in_accel_y_scale and in_accel_z_scale and makes available in_accel_scale. This is an ABI change, but hopefully in the 'no one will notice' category. The cleanup in interface is worth the small risk that there is a custom script out there somewhere that this will break. Signed-off-by:
Martin Kepplinger <martin.kepplinger@puri.sm> Acked-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Chuhong Yuan authored
Use regulator_bulk_() APIs to shrink driver size. Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Reviewed-by:
Brian Masney <masneyb@onstation.org> Tested-by:
-
Chuhong Yuan authored
Use devm_iio_device_register, which removes the tsl2772_remove function. Signed-off-by:
-
Chuhong Yuan authored
Use devm_add_action_or_reset to call tsl2772_chip_off when the device is removed. This also fixes the issue that the chip is turned off before the device is unregistered. Not marked for stable as fairly hard to hit the bug and this is in the middle of a set making other cleanups to the driver. Hence will probably need explicit backporting. Signed-off-by:
-
Chuhong Yuan authored
Use devm_add_action_or_reset to remove the call to tsl2772_disable_regulators_action to simplify the error path. Signed-off-by:
-
Stephen Boyd authored
We don't need dev_err() messages when platform_get_irq() fails now that platform_get_irq() prints an error message itself when something goes wrong. Let's remove these prints with a simple semantic patch. // <smpl> @@ expression ret; struct platform_device *E; @@ ret = ( platform_get_irq(E, ...) | platform_get_irq_byname(E, ...) ); if ( \( ret < 0 \| ret <= 0 \) ) { ( -if (ret != -EPROBE_DEFER) -{ ... -dev_err(...); -... } | ... -dev_err(...); ) ... } // </smpl> While we're here, remove braces on if statements that only have one statement (manually). Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: linux-iio@vger.kernel.org Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:Stephen Boyd <swboyd@chromium.org> Signed-off-by:
-
Chuhong Yuan authored
Use device-managed APIs to simplify the code. The remove functions are redundant now and can be deleted. Signed-off-by:
-
Denis Ciocca authored
This patch is trying to cleanup for good the buffers operation functions. There is no need of using preenable, all can be done into postenable. Let's also use logical sequence of operations as already done in accel driver. Finally also rename the goto label using operation to perform and not where it fails. Not stable material as not fixing a 'bug' but rather bringing the driver in line with general 'patterns' to allow a subsystem wide cleanup. Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
-
Denis Ciocca authored
This patch is trying to cleanup for good the buffers operation functions. Let's rename the goto label using operation to perform and not where it fails. Not stable material as not fixing a 'bug' but rather bringing the driver in line with general 'patterns' to allow a subsystem wide cleanup. Signed-off-by:
-
Denis Ciocca authored
This patch is trying to cleanup for good the buffers operation functions. There is no need of using preenable, all can be done into postenable. Let's also use logical sequence of operations as already done in accel driver. Finally also rename the goto label using operation to perform and not where it fails. Not stable material as not fixing a 'bug' but rather bringing the driver in line with general 'patterns' to allow a subsystem wide cleanup. Signed-off-by:
-
Denis Ciocca authored
This patch is trying to cleanup for good the buffers operation functions. There is no need of using preenable, all can be done into postenable. Let's also rename the goto label using operation to perform and not where it fails. Note, not stable material. This is cleaning up the logic flow rather than fixing a bug. Signed-off-by:
-
Lorenzo Bianconi authored
Signed-off-by:
-
Lorenzo Bianconi authored
Add support to STM ISM330DHCX 6-axis (acc + gyro) Mems sensor https://www.st.com/resource/en/datasheet/ism330dhcx.pdf Signed-off-by:
-
Lorenzo Bianconi authored
Move IIO channel definitions in st_lsm6dsx_sensor_settings in order to support sensors with different channels maps. This is a preliminary patch to add support for LSM9DS1 sensor to st_lsm6dsx driver. Signed-off-by:
-
Lorenzo Bianconi authored
Remove output register definition and inline register value since they are used only for iio channel definition. This is a preliminary patch to add support for LSM9DS1 sensor to st_lsm6dsx driver Signed-off-by:
-
Lorenzo Bianconi authored
Move fs_table in st_lsm6dsx_sensor_settings in order to support sensors with different gain maps. This is a preliminary patch to add support for LSM9DS1 sensor to st_lsm6dsx driver Tested-by:
-
Lorenzo Bianconi authored
Move sensor odr table in st_lsm6dsx_sensor_settings in order to support sensors with different odr maps. This is a preliminary patch to add support for LSM9DS1 sensor to st_lsm6dsx driver Tested-by:
-
Chuhong Yuan authored
Use device-managed APIs to simplify the code. The remove functions are redundant now and can be deleted. Signed-off-by:
-
Martin Kaiser authored
Add a binding for the Maxim Integrated MAX5432-MAX5435 family of digital potentiometers. Signed-off-by:
Martin Kaiser <martin@kaiser.cx> Reviewed-by:
-
Martin Kaiser authored
Add a driver for the Maxim Integrated MAX5432-MAX5435 family of digital potentiometers. These potentiometers are connected via I2C and have 32 wiper positions. Supported functionality - set the volatile wiper position - read the potentiometer scale Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX5432-MAX5435.pdf Signed-off-by:
-
- Jul 28, 2019
-
-
Beniamin Bia authored
Support for register access was added for devices which have software mode. Signed-off-by:
Beniamin Bia <beniamin.bia@analog.com> Signed-off-by:
-
Beniamin Bia authored
Support for ad7616 running in software was added. In order to activate the software mode, HW_RNGSEL pins must be pulled low. Oversampling and input ranges are now configured in corresponding registers. Ad7616 has multiple scale options when it is configured in software mode. Also, in order to support multiple devices in software mode, the spi calculation of registers address must be generic. Because the length of address and bit which specifies the read/write operation is different for every device, calculation of address was made generic. Signed-off-by:
-
Beniamin Bia authored
According to datasheet, ad7616 require at least 15ms after a restart to fully reconfigure and being able to receive new commands via spi. Signed-off-by:
-
Beniamin Bia authored
Because software mode and register access are only available in spi, they were moved in spi file and are accessbile via bops structure. The write_os/scale will be overwritten by sw_mode_config function. This patch was made in order to support devices in software mode without making the driver dependent to spi and increase the abstraction of the core. Signed-off-by:
-
Beniamin Bia authored
The common channel definition which are going to be used by both core file but also spi file, were moved in header file. Some devices have different channel definitions when are used in software mode, feature available only with spi, and those definitions will be added in spi file. Signed-off-by:
-
Linus Walleij authored
The mounting matrix for sensors was introduced in commit dfc57732 ("iio:core: mounting matrix support") However the device tree bindings are very terse and since this is a widely applicable property, we need a proper binding for it that the other bindings can reference. This will also be useful for other operating systems and sensor engineering at large. I think all 3D sensors should support it, the current situation is probably that the mounting information is confined in magic userspace components rather than using the mounting matrix, which is not good for portability and reuse. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Gregor Boirie <gregor.boirie@parrot.com> Cc: Sebastian Reichel <sre@kernel.org> Cc: Samu Onkalo <samu.onkalo@intel.com> Cc: devicetree@vger.kernel.org Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Reviewed-by:
-
Fabien Lahoudere authored
Embedded controller return minimum and maximum frequencies, unfortunately we have no way to know the step for all available frequencies. Even if not complete, we can return a list of known values using the standard read_avail callback (IIO_CHAN_INFO_SAMP_FREQ) to provide them to userland. Now cros_ec_* sensors provides frequencies values in sysfs like this: "0 min max". 0 is always true to disable the sensor. Default frequencies are provided for earlier protocol. Signed-off-by:
Nick Vaccaro <nvaccaro@chromium.org> Signed-off-by:
Fabien Lahoudere <fabien.lahoudere@collabora.com> [rebased on top of iio/testing and solved conflicts] Signed-off-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by:
-
Gwendal Grignou authored
Veyron minnie embedded controller presents 2 accelerometers using an older interface. Add function to query the data in cros_ec_accel. Verify accelerometers on veyron-minnie are presented and working. Signed-off-by:
Gwendal Grignou <gwendal@chromium.org> Signed-off-by:
-
Gwendal Grignou authored
Remove duplicate code in cros-ec-accel-legacy, use cros-ec-sensors-core functions and structures when possible. On glimmer, check the 2 accelerometers are presented and working. Signed-off-by:
-
Gwendal Grignou authored
INFO_SCALE is set both for each channel and all channels. iio is using all channel setting, so the error was not user visible. Signed-off-by:
-
Gwendal Grignou authored
To allow cros_ec iio core library to be used with legacy device, add a vector to rotate sensor data if necessary: legacy devices are not reporting data in HTML5/Android sensor referential. Check the data is not rotated on recent chromebooks that use the HTML5 standard to present sensor data. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Fabien Lahoudere authored
This patch adds a function to determine which version of the protocol is used to communicate with EC. Signed-off-by:
-
Chuhong Yuan authored
Make use of devm_counter_register. Then we can remove redundant unregistration API usage to make code simpler. Signed-off-by:
-
Sean Nyekjaer authored
No need for using reverse logic in the irq return, fix this by flip things around. Signed-off-by:
Sean Nyekjaer <sean@geanix.com> Signed-off-by:
-
Vitor Soares authored
For today the st_lsm6dsx driver support LSM6DSO and LSM6DSR sensor only in spi and i2c mode. The LSM6DSO and LSM6DSR are also i3c capable so let's give i3c support to them. Signed-off-by:
Vitor Soares <vitor.soares@synopsys.com> Acked-by:
Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by:
-
Jonathan Cameron authored
Needed for the st_lsm6dsx_i3c.c driver
-
Christophe JAILLET authored
Everything is about mmc35240_ except MMC53240_WAIT_SET_RESET (3 and 5 switched). This is likely a typo. Define and use MMC35240_WAIT_SET_RESET instead. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Wolfram Sang authored
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an ERRPTR which we use in error handling. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
