Fix the pm sys device .name initialiser which was
missed when updating the last patch submission.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds functions to set clkout rate for Samsung S3C2410
This patch supersedes 4884/1, that contained an error

Comments from Ben Dooks:

 Note, looks like this needs to be applied before 4882/1

Signed-off-by: Davide Rizzo <davide@elpa.it>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add the TinCanTools Hammer board to list of supported machines in the
arch/arm/mach-s3c2410 directory, as well as a default config entry. the
mach-tct_hammer.c file initializes basic i/o, clocks, irqs, as well as
the mtd flash layout if enabled in the kernel configuration.

Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This is a small addition of forgotten defines to regs-gpio.h include file for the Samsung S3C2410 ARM9 SoC

Signed-off-by: Davide Rizzo <davide@elpa.it>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There seems to be some problem with at-least the S3C2440 and
bus traffic during an reset. It is unlikely, but still possible
that the system will hang in such a way that the watchdog cannot
get the system out of the state it is in.

Change to making the code that calls the watchdog reset run from
cached memory so that instruction fetches have quiesced before the
watchdog fires.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

All current Simtec designs source the DCLK outputs from
the UPLL. This means the DCLK's parent must be set to UPLL
so that anything enabling and disabling an UPLL sourced
clock does not shutdown the DCLK due to missing open counts.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix the name of the S3C2412_CLKDIVN_ARMDIVN define.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Change GPA21 to output over reset so that nRSTOUT is not
asserted whilst suspended.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add initial defines for the S3C2412's memory controller registers.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This fixes the builtin RTL8139 NIC on the Medion MD9580-F laptop.  The
BIOS reports the interrupt routing incorrectly.  I recently added a
quirk to work around this, and this patch fixes a typo in the quirk.

We pad every ACPI pathname component to four characters, so ".ISA." will
never match anything.  We need ".ISA_." instead.

Thank you Johann-Nikolaus Andreae <johann-nikolaus.andreae@nacs.de>
for patiently testing this patch.

See http://bugzilla.kernel.org/show_bug.cgi?id=4773



Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Fix docbook problem
  ASoC/TLV320AIC3X: Stop I2C driver ID abuse
  i2c-omap: Fix unhandled fault
  i2c-bfin-twi: Disable BF54x support for now

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: MMU: Fix memory leak on guest demand faults
  KVM: VMX: convert init_rmode_tss() to slots_lock
  KVM: MMU: handle page removal with shadow mapping
  KVM: MMU: Fix is_rmap_pte() with io ptes
  KVM: VMX: Restore tss even on x86_64

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  [PATCH] get stack footprint of pathname resolution back to relative sanity
  [PATCH] double iput() on failure exit in hugetlb
  [PATCH] double dput() on failure exit in tiny-shmem
  [PATCH] fix up new filp allocators
  [PATCH] check for null vfsmount in dentry_open()
  [PATCH] reiserfs: eliminate private use of struct file in xattr
  [PATCH] sanitize hppfs
  hppfs pass vfsmount to dentry_open()
  [PATCH] restore export of do_kern_mount()

While backporting 72dc67a6

, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline).  This caused a page reference leak, resulting in a
fairly massive memory leak.

Fix by removing the extraneous gfn_to_page() call.

Signed-off-by: Avi Kivity <avi@qumranet.com>

init_rmode_tss was forgotten during the conversion from mmap_sem to
slots_lock.

INFO: task qemu-system-x86:3748 blocked for more than 120 seconds.
Call Trace:
 [<ffffffff8053d100>] __down_read+0x86/0x9e
 [<ffffffff8053fb43>] do_page_fault+0x346/0x78e
 [<ffffffff8053d235>] trace_hardirqs_on_thunk+0x35/0x3a
 [<ffffffff8053dcad>] error_exit+0x0/0xa9
 [<ffffffff8035a7a7>] copy_user_generic_string+0x17/0x40
 [<ffffffff88099a8a>] :kvm:kvm_write_guest_page+0x3e/0x5f
 [<ffffffff880b661a>] :kvm_intel:init_rmode_tss+0xa7/0xf9
 [<ffffffff880b7d7e>] :kvm_intel:vmx_vcpu_reset+0x10/0x38a
 [<ffffffff8809b9a5>] :kvm:kvm_arch_vcpu_setup+0x20/0x53
 [<ffffffff8809a1e4>] :kvm:kvm_vm_ioctl+0xad/0x1cf
 [<ffffffff80249dea>] __lock_acquire+0x4f7/0xc28
 [<ffffffff8028fad9>] vfs_ioctl+0x21/0x6b
 [<ffffffff8028fd75>] do_vfs_ioctl+0x252/0x26b
 [<ffffffff8028fdca>] sys_ioctl+0x3c/0x5e
 [<ffffffff8020b01b>] system_call_after_swapgs+0x7b/0x80

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

Do not assume that a shadow mapping will always point to the same host
frame number.  Fixes crash with madvise(MADV_DONTNEED).

[avi: move after first printk(), add another printk()]

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>

is_rmap_pte() doesn't take into account io ptes, which have the avail bit set.

Signed-off-by: Avi Kivity <avi@qumranet.com>

The vmx hardware state restore restores the tss selector and base address, but
not its length.  Usually, this does not matter since most of the tss contents
is within the default length of 0x67.  However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted.  The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.

Fix by restoring the tss length.  Note that i386 had this working already.

Closes bugzilla 10246.

Signed-off-by: Avi Kivity <avi@qumranet.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: Fix cut-and-paste error in rtl8150.c
  USB: ehci: stop vt6212 bus hogging
  USB: sierra: add another device id
  USB: sierra: dma fixes
  USB: add support for Motorola ROKR Z6 cellphone in mass storage mode
  USB: isd200: fix memory leak in isd200_get_inquiry_data
  USB: pl2303: another product ID
  USB: new quirk flag to avoid Set-Interface
  USB: fix gadgetfs class request delegation

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  driver core: debug for bad dev_attr_show() return value.
  UIO: add pgprot_noncached() to UIO mmap code

Revert as it is reported to cause problems for people.

commit 4348a2dc


Author: Shaohua Li <shaohua.li@intel.com>
Date:   Wed Oct 24 10:45:08 2007 +0800

    pcie: utilize pcie transaction pending bit

    PCIE has a mechanism to wait for Non-Posted request to complete. I think
    pci_disable_device is a good place to do this.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Due to the regression reported at
http://bugzilla.kernel.org/show_bug.cgi?id=10065



Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Soeren Sonnenburg <kernel@nn7.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

lockdep goes off on the iova copy_reserved_iova() because it and a function
it calls grabs locks in the from, and the to of the copy operation.

The function grab locks of the same lock classes triggering the warning.  The
first lock grabbed is for the constant reserved areas that is never accessed
after early boot.  Technically you could do without grabbing the locks for the
"from" structure its copying reserved areas from.

But dropping the from locks to me looks wrong, even though it would be ok.

The affected code only runs in early boot as its setting up the DMAR
engines.

This patch gives the reserved_ioval_list locks special lockdep classes.

Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Try to find the culprit who caused
http://bugzilla.kernel.org/show_bug.cgi?id=10150



Cc: <balajirrao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Mapping of physical memory in UIO needs pgprot_noncached() to ensure
that IO memory is not cached. Without pgprot_noncached(), it (accidentally)
works on x86 and arm, but fails on PPC.

Signed-off-by: Jean-Samuel Chenard <jsamch@gmail.com>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The VIA VT6212 defaults to only waiting 1us between passes over EHCI's
async ring, which hammers PCI badly ... and by preventing other devices
from accessing the bus, causes problems like drops in IDE throughput,
a problem that's been bugging users of those chips for several years.

A (partial) datasheet for this chip eventually turned up, letting us
see how to make it use a VIA-specific register to switch over to the
the normal 10us value instead, as suggested by the EHCI specification
Solution noted by Lev A. Melnikovsky.

It's not clear whether this register exists on other VIA chips; we
know that it's ineffective on the vt8235.  So this patch only applies
to chips that seem to be incarnations of the (discrete) vt6212.

Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Lev A. Melnikovsky <melnikovsky@mail.ru>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add support for the MC8775 device to the sierra driver.

Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

while I was adding autosuspend to that driver I noticed a few issues.
You were having DMAed buffers as a part of a structure.
This will fail on platforms that are not DMA-coherent (arm, sparc, ppc, ...)
Please test this patch to fix it.

Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Motorola ROKR Z6 cellphone has bugs in its USB, so it is impossible to use
it as mass storage. Patch describes new "unusual" USB device for it with
FIX_INQUIRY and FIX_CAPACITY flags and new BULK_IGNORE_TAG flag.
Last flag relaxes check for equality of bcs->Tag and us->tag in
usb_stor_Bulk_transport routine.

Signed-off-by: Constantin Baranov <const@tltsu.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If the inquiry fails then the info structure on us->extra was not freed.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Device like this http://aldiga.com/english/A-100-USB-EDGE10.htm


contains Prolific 2303 chip.
Actually their site a bit outdated - I have AlDiga AL-11U
GSM/GPRS/EDGE modem and it works with pl2303 module after adding
corresponding product ID.

By default modem uses baud rate 460800.  GSM chipset - SIMCom SIM600,
quad band 850/900/1800/1900 MHz

Device info:

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=067b ProdID=0611 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=pl2303
E:  Ad=81(I) Atr=03(Int.) MxPS=  10 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

From: Max Arnold <lwarxx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request.  A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

gadgetfs (drivers/usb/gadget/inode.c) was not delegating all
non-device requests to userspace.  This patch makes the handling of
all request cases consistent.

Signed-off-by: Roy Hashimoto <hashimot@alumni.caltech.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] mpc5200: Fix incorrect compatible string for the mdio node
  [POWERPC] Update some defconfigs

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] ahci: SB600 workaround is suspect... play it safe for now
  sata_promise: fix hardreset hotplug events, take 2
  libata: improve HPA error handling
  libata: assume no device is attached if both IDENTIFYs are aborted
  pata_it821x: use raw nbytes in check_atapi_dma
  libata: implement ata_qc_raw_nbytes()

At least one report claims that a878539e


failed to solve lockups, whereas the old limit-to-32-bit trick worked.

Restore the 32-bit limit, but also leave the 255-sector limit in place,
because we know that's needed as well.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-linus:
  kbuild: soften modpost checks when doing cross builds

A Promise SATA controller will signal hotplug events when a hard
reset (COMRESET) is done on a port. These events aren't masked by
the driver, and the unexpected interrupts will cause a sequence
of failed reset attempts util libata's EH finally gives up.

This has not been a common problem so far, but the pending libata
hardreset-by-default changes makes it a critical issue.

The solution is to disable hotplug events before a reset, and to
reenable them afterwards. (Promise's driver does this too.)

This patch adds SATA-specific versions of ->freeze() and ->thaw()
that also disable and enable hotplug events. PATA ports continue
to use the old versions of ->freeze() and ->thaw().

Accesses to the hotplug register must be serialised via host->lock.
We rely on ap->lock == &ap->host->lock and that libata takes this
lock before ->freeze() and ->thaw(). Document this requirement.
The interrupt handler is adjusted so its hotplug register accesses
are inside the region protected by host->lock.

Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4,
FastTrack TX4000) with various combinations of SATA and PATA disks,
with and without the pending hardreset-by-default changes.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>