FQ rate limiting suffers from two problems, reported
by Steinar :

1) FQ enforces a delay when flow quantum is exhausted in order
to reduce cpu overhead. But if packets are small, current
delay computation is slightly wrong, and observed rates can
be too high.

Steinar had this problem because he disabled TSO and GSO,
and default FQ quantum is 2*1514.

(Of course, I wish recent TSO auto sizing changes will help
to not having to disable TSO in the first place)

2) maxrate was not used for forwarded flows (skbs not attached
to a socket)

Tested:

tc qdisc add dev eth0 root est 1sec 4sec fq maxrate 8Mbit
netperf -H lpq84 -l 1000 &
sleep 10 ; tc -s qdisc show dev eth0
qdisc fq 8003: root refcnt 32 limit 10000p flow_limit 100p buckets 1024
 quantum 3028 initial_quantum 15140 maxrate 8000Kbit
 Sent 16819357 bytes 11258 pkt (dropped 0, overlimits 0 requeues 0)
 rate 7831Kbit 653pps backlog 7570b 5p requeues 0
  44 flows (43 inactive, 1 throttled), next packet delay 2977352 ns
  0 gc, 0 highprio, 5545 throttled

lpq83:~# tcpdump -p -i eth0 host lpq84 -c 12
09:02:52.079484 IP lpq83 > lpq84: . 1389536928:1389538376(1448) ack 3808678021 win 457 <nop,nop,timestamp 961812 572609068>
09:02:52.079499 IP lpq83 > lpq84: . 1448:2896(1448) ack 1 win 457 <nop,nop,timestamp 961812 572609068>
09:02:52.079906 IP lpq84 > lpq83: . ack 2896 win 16384 <nop,nop,timestamp 572609080 961812>
09:02:52.082568 IP lpq83 > lpq84: . 2896:4344(1448) ack 1 win 457 <nop,nop,timestamp 961815 572609071>
09:02:52.082581 IP lpq83 > lpq84: . 4344:5792(1448) ack 1 win 457 <nop,nop,timestamp 961815 572609071>
09:02:52.083017 IP lpq84 > lpq83: . ack 5792 win 16384 <nop,nop,timestamp 572609083 961815>
09:02:52.085678 IP lpq83 > lpq84: . 5792:7240(1448) ack 1 win 457 <nop,nop,timestamp 961818 572609074>
09:02:52.085693 IP lpq83 > lpq84: . 7240:8688(1448) ack 1 win 457 <nop,nop,timestamp 961818 572609074>
09:02:52.086117 IP lpq84 > lpq83: . ack 8688 win 16384 <nop,nop,timestamp 572609086 961818>
09:02:52.088792 IP lpq83 > lpq84: . 8688:10136(1448) ack 1 win 457 <nop,nop,timestamp 961821 572609077>
09:02:52.088806 IP lpq83 > lpq84: . 10136:11584(1448) ack 1 win 457 <nop,nop,timestamp 961821 572609077>
09:02:52.089217 IP lpq84 > lpq83: . ack 11584 win 16384 <nop,nop,timestamp 572609090 961821>

Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl ops where introduced by c075b130 ("ip6tnl: advertise tunnel param via
rtnl"), but I forget to assign rtnl ops to fb tunnels.

Now that it is done, we must remove the explicit call to
unregister_netdevice_queue(), because  the fallback tunnel is added to the queue
in ip6_tnl_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this
is valid since commit 0bd87628

 ("ip6tnl: add x-netns support")).

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl ops where introduced by ba3e3f50 ("sit: advertise tunnel param via
rtnl"), but I forget to assign rtnl ops to fb tunnels.

Now that it is done, we must remove the explicit call to
unregister_netdevice_queue(), because  the fallback tunnel is added to the queue
in sit_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this
is valid since commit 5e6700b3

 ("sit: add support of x-netns")).

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_tunnel bug fixes from Steffen Klassert.

Signed-off-by: David S. Miller <davem@davemloft.net>

When queueing the netdevices for removal, we queue the
fallback device twice in ip_tunnel_destroy(). The first
time when we queue all netdevices in the namespace and
then again explicitly. Fix this by removing the explicit
queueing of the fallback device.

Bug was introduced when network namespace support was added
with commit 6c742e71

 ("ipip: add x-netns support").

Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Git commit 0e6fbc5b

 ("ip_tunnels: extend iptunnel_xmit()")
moved the IP header installation to iptunnel_xmit() and
changed skb_push() to __skb_push(). This makes possible
bugs hard to track down, so change it back to skb_push().

Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we can not update the tunnel parameters of
the fallback tunnels because we don't find them in the
hash lists. Fix this by adding them on initialization.

Bug was introduced with commit c5441932


("GRE: Refactor GRE tunneling code.")

Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We might extend the used aera of a skb beyond the total
headroom when we install the ipip header. Fix this by
calling skb_cow_head() unconditionally.

Bug was introduced with commit c5441932


("GRE: Refactor GRE tunneling code.")

Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter/IPVS fixes for your net
tree, they are:

* Fix BUG_ON splat due to malformed TCP packets seen by synproxy, from
  Patrick McHardy.

* Fix possible weight overflow in lblc and lblcr schedulers due to
  32-bits arithmetics, from Simon Kirby.

* Fix possible memory access race in the lblc and lblcr schedulers,
  introduced when it was converted to use RCU, two patches from
  Julian Anastasov.

* Fix hard dependency on CPU 0 when reading per-cpu stats in the
  rate estimator, from Julian Anastasov.

* Fix race that may lead to object use after release, when invoking
  ipvsadm -C && ipvsadm -R, introduced when adding RCU, from Julian
  Anastasov.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

o Interface needs to be brought down and up while configuring SR-IOV.
  Protect interface up/down using rtnl_lock()/rtnl_unlock()

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dma descriptors indexes are only initialized on the probe function.

If a packet is on the buffer when temac_stop is called, the dma
descriptors indexes can be left on a incorrect state where no other
package can be sent.

So an interface could be left in an usable state after ifdow/ifup.

This patch makes sure that the descriptors indexes are in a proper
status when the device is open.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit c93bdd0e

 ("netvm: allow skb allocation to use PFMEMALLOC
reserves"), hole size is one bit less than what is written in the comment.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible for the timer handlers to run after the call to
ipv6_mc_down so use in6_dev_put instead of __in6_dev_put in the
handler function in order to do proper cleanup when the refcnt
reaches 0. Otherwise, the refcnt can reach zero without the
inet6_dev being destroyed and we end up leaking a reference to
the net_device and see messages like the following,

unregister_netdevice: waiting for eth0 to become free. Usage count = 1

Tested on linux-3.4.43.

Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible for the timer handlers to run after the call to
ip_mc_down so use in_dev_put instead of __in_dev_put in the handler
function in order to do proper cleanup when the refcnt reaches 0.
Otherwise, the refcnt can reach zero without the in_device being
destroyed and we end up leaking a reference to the net_device and
see messages like the following,

unregister_netdevice: waiting for eth0 to become free. Usage count = 1

Tested on linux-3.4.43.

Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.

In this particular case __initdata is incorrect as moxart_mac_driver
can be used after the driver gets initialized.

Also while at it static-ize moxart_mac_driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gre_hlen already accounts for sizeof(struct ipv6_hdr) + gre header,
so initialize max_headroom to zero. Otherwise the

	if (encap_limit >= 0) {
		max_headroom += 8;
		mtu -= 8;
	}

increments an uninitialized variable before max_headroom was reset.

Found with coverity: 728539

Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.

Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 894116bd

.

I applied the wrong version of this patch, correct
version coming up.

Signed-off-by: David S. Miller <davem@davemloft.net>

Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567



Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:

dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.

The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification.  With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are.  This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device.  Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave.  But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error

Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.

This is also needed for the ALLMULTI flag

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

When TCP Small Queues was added, we used a sysctl to limit amount of
packets queues on Qdisc/device queues for a given TCP flow.

Problem is this limit is either too big for low rates, or too small
for high rates.

Now TCP stack has rate estimation in sk->sk_pacing_rate, and TSO
auto sizing, it can better control number of packets in Qdisc/device
queues.

New limit is two packets or at least 1 to 2 ms worth of packets.

Low rates flows benefit from this patch by having even smaller
number of packets in queues, allowing for faster recovery,
better RTT estimations.

High rates flows benefit from this patch by allowing more than 2 packets
in flight as we had reports this was a limiting factor to reach line
rate. [ In particular if TX completion is delayed because of coalescing
parameters ]

Example for a single flow on 10Gbp link controlled by FQ/pacing

14 packets in flight instead of 2

$ tc -s -d qd
qdisc fq 8001: dev eth0 root refcnt 32 limit 10000p flow_limit 100p
buckets 1024 quantum 3028 initial_quantum 15140
 Sent 1168459366606 bytes 771822841 pkt (dropped 0, overlimits 0
requeues 6822476)
 rate 9346Mbit 771713pps backlog 953820b 14p requeues 6822476
  2047 flow, 2046 inactive, 1 throttled, delay 15673 ns
  2372 gc, 0 highprio, 0 retrans, 9739249 throttled, 0 flows_plimit

Note that sk_pacing_rate is currently set to twice the actual rate, but
this might be refined in the future when a flow is in congestion
avoidance.

Additional change : skb->destructor should be set to tcp_wfree().

A future patch (for linux 3.13+) might remove tcp_limit_output_bytes

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).

Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fq_reset() should drops all packets in queue, including
throttled flows.

This patch moves code from fq_destroy() to fq_reset()
to do the cleaning.

fq_change() must stop calling fq_dequeue() if all remaining
packets are from throttled flows.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 8ed78166

 ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.

This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consider the scenario where an IPv6 router is advertising a fixed
preferred_lft of 1800 seconds, while the valid_lft begins at 3600
seconds and counts down in realtime.

A client should reset its preferred_lft to 1800 every time the RA is
received, but a bug is causing Linux to ignore the update.

The core problem is here:
  if (prefered_lft != ifp->prefered_lft) {

Note that ifp->prefered_lft is an offset, so it doesn't decrease over
time.  Thus, the comparison is always (1800 != 1800), which fails to
trigger an update.

The most direct solution would be to compute a "stored_prefered_lft",
and use that value in the comparison.  But I think that trying to filter
out unnecessary updates here is a premature optimization.  In order for
the filter to apply, both of these would need to hold:

  - The advertised valid_lft and preferred_lft are both declining in
    real time.
  - No clock skew exists between the router & client.

So in this patch, I've set "update_lft = 1" unconditionally, which
allows the surrounding code to be greatly simplified.

Signed-off-by: Paul Marks <pmarks@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While sending packet skb_cow_head() can change skb header which
invalidates inner_iph pointer to skb header. Following patch
avoid using it. Found by code inspection.

This bug was introduced by commit 0e6fbc5b

 (ip_tunnels: extend
iptunnel_xmit()).

Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.

The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb

 ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').

CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.

Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of RCU api makes vxlan code easier to understand.  It also
fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference.
In rare case without ACCESS_ONCE() compiler might omit vs on
sk_user_data dereference.
Compiler can use vs as alias for sk->sk_user_data, resulting in
multiple sk_user_data dereference in rcu read context which
could change.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the flexcan_chip_start() function first the flexcan core is going through
the soft reset sequence, then the RX FIFO is enabled.

With the hardware is put into FIFO mode, message buffers 1...7 are reserved by
the FIFO engine. The remaining message buffers are in reset default values.
This patch removes the bogus initialization of the message buffers, as it
causes an imprecise external abort on imx6.

Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

TCP packets hitting the SYN proxy through the SYNPROXY target are not
validated by TCP conntrack. When th->doff is below 5, an underflow happens
when calculating the options length, causing skb_header_pointer() to
return NULL and triggering the BUG_ON().

Handle this case gracefully by checking for NULL instead of using BUG_ON().

Reported-by: Martin Topholm <mph@one.com>
Tested-by: Martin Topholm <mph@one.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

A host might need net_secret[] and never open a single socket.

Problem added in commit aebda156


("net: defer net_secret[] initialization")

Based on prior patch from Hannes Frederic Sowa.

Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@strressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is currently serialization network namespaces exiting and
network devices exiting as the final part of netdev_run_todo does not
happen under the rtnl_lock.  This is compounded by the fact that the
only list of devices unregistering in netdev_run_todo is local to the
netdev_run_todo.

This lack of serialization in extreme cases results in network devices
unregistering in netdev_run_todo after the loopback device of their
network namespace has been freed (making dst_ifdown unsafe), and after
the their network namespace has exited (making the NETDEV_UNREGISTER,
and NETDEV_UNREGISTER_FINAL callbacks unsafe).

Add the missing serialization by a per network namespace count of how
many network devices are unregistering and having a wait queue that is
woken up whenever the count is decreased.  The count and wait queue
allow default_device_exit_batch to wait until all of the unregistration
activity for a network namespace has finished before proceeding to
unregister the loopback device and then allowing the network namespace
to exit.

Only a single global wait queue is used because there is a single global
lock, and there is a single waiter, per network namespace wait queues
would be a waste of resources.

The per network namespace count of unregistering devices gives a
progress guarantee because the number of network devices unregistering
in an exiting network namespace must ultimately drop to zero (assuming
network device unregistration completes).

The basic logic remains the same as in v1.  This patch is now half
comment and half rtnl_lock_unregistering an expanded version of
wait_event performs no extra work in the common case where no network
devices are unregistering when we get to default_device_exit_batch.

Reported-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a router is doing DNAT for 6to4/6rd packets the latest
anti-spoofing commit 218774dc

 ("ipv6: add anti-spoofing checks for
6to4 and 6rd") will drop them because the IPv6 address embedded does
not match the IPv4 destination. This patch will allow them to pass by
testing if we have an address that matches on 6to4/6rd interface.  I
have been hit by this problem using Fedora and IPV6TO4_IPV4ADDR.
Also, log the dropped packets (with rate limit).

Signed-off-by: Catalin(ux) M. BOIE <catab@embedromix.ro>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 638c5115

(USBNET: support DMA SG) introduces DMA SG
if the usb host controller is capable of building packet from
discontinuous buffers, but missed handling padding packet when
building DMA SG.

This patch attachs the pre-allocated padding packet at the
end of the sg list, so padding packet can be sent to device
if drivers require that.

Reported-by: David Laight <David.Laight@aculab.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Commit 7e2cf4fe
  ("qlcnic: change driver hardware interface mechanism")
  has overwritten
  commit b43e5ee7


  ("qlcnic: Register device in FAILED state")

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN priority is not being displayed for a VF currently when user executes
"ip link show" command. This patch fixes it.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thix fix allows the VLAN priority to be configured for a VF interface
via the "ip link set DEVICE vf NUM" path.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>