The 'interrupts' property has an extra cell by mistake.

Fix this, so that the following build warning is gone:

 DTC     arch/arm/boot/dts/imx6ul-pico-hobbit.dtb
arch/arm/boot/dts/imx6ul-pico-hobbit.dtb: Warning (interrupts_property): interrupts size is (12), expected multiple of 8 in /soc/aips-bus@2000000/ethernet@20b4000/mdio/ethernet-phy@1

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx6qp variant also has sata, so add support for it.

Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt,
the property for specifying the PCIe regulator is 'vpcie-supply', so
use the correct one.

Also fix the polarity of GPIO2_24 so that the regulator can operate
correctly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit c26ebe98

 ("PCI: imx6: Add regulator support"), it is
possible to pass the 'vpcie-supply' property to describe the PCIE supply.

This way we can remove the 'regulator-always-on' property from the
regulator and have a better device tree description.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This works identically to imx6sx-tempmon on both imx6ul and imx6ull.
It just needs to be defined in dts.

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On imx6sx accessing OCOTP directly is wrong because the ocotp clock
needs to be enabled first. Use the nvmem-cells binding instead.

This requirement does not apply to older imx6qdl chips because there the
ocotp access clock (clk_ipg_s) is always enabled.

This is visible by comparing the "System Clocks, Gating, and Override"
tables (OCOTP rows) in the 6DQ and 6SX manuals:
http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6SXRM.pdf
http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6DQRM.pdf



This happens to work right now because the ocotp clock might be enabled
for some other reason. In particular the it might be enabled from the
bootloader and it only gets disabled late during boot in
clk_disable_unused, after imx-thermal has completed probing.

If imx-thermal is compiled as a module then the system can hang on
probe.

Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The container node in the iomuxc node is no longer necessary and causes
pinctl errors on the Ventana boards with analog video capture
since aa12693e

:

pinctrl core: initialized pinctrl subsystem
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/adv7180grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/ipu2_csi1grp
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Latest wandboard hardware revision is revd1, which brings the following
new features:

- PFUZE100 PMIC
- AR8035 Ethernet PHY
- Upgrade Wifi/BT chip to BCM4339/BCM43430.

Add support for the mx6, mx6dl and mx6qp revd1 variants.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

By default, the lcdif_pre_sel mux is switched to the pll3_pfd1_540m PFD
source. If this mux is allowed to propagate rate changes to its parent,
setting the LCDIF pixel clock rate to 9 MHz, as required by the LCD
panel, will cause the pll3_pfd1_540m PFD to be switched away from its
nominal rate to 288 MHz.
This has no negative side effects, as there are no other children to
this PFD. Still, to avoid surprises, it might be preferrable to switch
to the designated video PLL (pll5_video_div) as clock source for the
LCDIF pixel clock.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx-i2c driver supports automatic bus recovery via the GPIO
function of the I2C pins. Enable this functionality for the Ka-Ro
electronics TX53 modules.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Don't rely on the padctl settings established by the boot loader, but
explicitly specify the padctl values in DTB. This is also necessary to
be able to use the DTB files from the Linux kernel for future U-Boot
versions that support HW configuration via DTB.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As the DS1339 driver now supports enabling the trickle charge feature
via DTB, add the appropriate properties to utilize this feature.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The display, that incorporates this touchpanel is obsolete and won't
be supported any more.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.

The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The current GPL only licensing on the dts files makes it very
impractical for other software components licensed under another
license.

In order to make it easier for them to reuse our device trees,
relicense our dts files first under a GPL/X11 dual-license.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As the DS1339 driver now supports enabling the trickle charge feature
via DTB, add the appropriate properties to utilize this feature.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.

The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The current GPL only licensing on the dts file makes it very
impractical for other software components licensed under another
license.

In order to make it easier for them to reuse our device trees,
relicense our dts files first under a GPL/X11 dual-license.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Contrary to later i.MX SoCs, the parallel display interface pad groups on
i.MX51 are called DISP1 and DISP2 in the Reference Manual, not DISP0 and
DISP1.

Fix this inconsistence by changing the DISP names in the i.mx51 dts.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warnings are seen with W=1:

Warning (unit_address_vs_reg): Node /display@di0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /display@di1 has a unit name, but no reg property

Fix all these warnings by changing 'display@diX' to 'dispX'.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the built-in touchscreen controller present on MX25.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warnings are seen with W=1:

Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit
address format error, expected "900000"
Warning (simple_bus_reg): Node /soc/aips-bus@02000000 simple-bus unit
address format error, expected "2000000"
Warning (simple_bus_reg): Node /soc/aips-bus@02000000/pxp@020f0000
simple-bus unit address format error, expected "20f0000"
(...)

Remove the leading zeroes from unit addresses to fix the warnings.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warnings are seen with W=1:

Warning (unit_address_format): Node /interrupt-controller@00a01000 unit
name should not have leading 0s
Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit address
format error, expected "900000"
Warning (simple_bus_reg): Node /soc/dma-apbh@01804000 simple-bus unit
address format error, expected "1804000"
(...)

Remove the leading zeroes from unit addresses to fix the warnings.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On the Utilite Pro the CEC line is wired up to the HDMI connector.
Add the required pinctrl setting.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit c26ebe98

 ("PCI: imx6: Add regulator support"), it is
possible to pass the 'vpcie-supply' property to describe the PCIE supply.

This way we can remove the 'regulator-always-on' property from the
regulator and have a better device tree description.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for can1 and can2 nodes on Engicam i.CoreM6 RQS
QDL module boards.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

max11801 touchscreen on Engicam iCoreM6 DualLite/Solo module is
connected via i2c1, so add max11801: touchscreen@48 on i2c1.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch replace fsl,imx-audio-sgtl5000 and use simple-audio-card
for Engicam i.CoreM6 RQS QDL platform boards.

This patch also fix, pinctrl_adumux.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6q, imx6dl icore-rqs modules share common sound nodes,
so move the sound nodes from imx6q-icore-rqs into dtsi so-that
both can share the common node details.

And also replace codec: sgtl5000@0a => sgtl5000: codec@a
on imx6q-icore-rqs.dts to [label:] node-name[@unit-address]
according to devicetree specification from ePAPER v1.1

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Linux Sound card now uses generic simple-audio-card, so add
the same along with related audmux and codec(via u2c3) for
i.CoreM6 QDL module boards.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Working items:

- 800MHz CPU
- 2GB of RAM (DDR3)
- 4GB of eMMC storage
- 1T1R WiFi 2.4 GHz
- Power management support
- 1x 10/100/1000 Mbps Ethernet WAN port
- 2x USB 2.0 Host
- PCIe
- HDMI/VGA/LVDS display
- 1x UART for RS232/422/485
- 2x UART for RS232
- 1x UART for serial console
- 1x CAN bus

Specification: http://nutsboard.org/pistachio



Signed-off-by: YuanCheng Cheng <onlywig@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add initial imx6sx-softing-vining-2000 board support.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is causing issues with some specific controller configurations, as
the platform isn't power limited it's better to keep it disabled.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Just like the OTG port, USB H1 has no over-current detection wired up.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

PPD is a product from GE Healthcare to monitor vital biometric signals.

Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Device Tree binding document for GE Healthcare USB Management
Controller (ACHC).

Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx7d-pico has an ap6212 wifi chip connected to usdhc2 port.

Add support for the usdhc2 port and to the WL_REG_ON regulator
so Wifi can be functional on this board.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull UBI updates from Richard Weinberger:
 "Minor improvements"

* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: Fix two typos in comments
  ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines