iio: envelope-detector: ADC driver based on a DAC and a comparator (b475f80b) · Commits · github.com / kvm-riscv / linux

Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector

0 → 100644

+36 −0

Original line number	Diff line number	Diff line
		What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_invert
		Date: October 2016
		KernelVersion: 4.9
		Contact: Peter Rosin <peda@axentia.se>
		Description:
		The DAC is used to find the peak level of an alternating
		voltage input signal by a binary search using the output
		of a comparator wired to an interrupt pin. Like so:
		_
		\| \
		input +------>-------\|+ \
		\| \
		.-------. \| }---.
		\| \| \| / \|
		\| dac\|-->--\|- / \|
		\| \| \|_/ \|
		\| \| \|
		\| \| \|
		\| irq\|------<-------'
		\| \|
		'-------'
		The boolean invert attribute (0/1) should be set when the
		input signal is centered around the maximum value of the
		dac instead of zero. The envelope detector will search
		from below in this case and will also invert the result.
		The edge/level of the interrupt is also switched to its
		opposite value.

		What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_compare_interval
		Date: October 2016
		KernelVersion: 4.9
		Contact: Peter Rosin <peda@axentia.se>
		Description:
		Number of milliseconds to wait for the comparator in each
		step of the binary search for the input peak level. Needs
		to relate to the frequency of the input signal.

MAINTAINERS

+2 −0

Original line number	Diff line number	Diff line
		@@ -6131,7 +6131,9 @@ IIO ENVELOPE DETECTOR
		M: Peter Rosin <peda@axentia.se>
		L: linux-iio@vger.kernel.org
		S: Maintained
		F: Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector
		F: Documentation/devicetree/bindings/iio/adc/envelope-detector.txt
		F: drivers/iio/adc/envelope-detector.c

		IIO SUBSYSTEM AND DRIVERS
		M: Jonathan Cameron <jic23@kernel.org>

drivers/iio/adc/Kconfig

+10 −0

Original line number	Diff line number	Diff line
		@@ -207,6 +207,16 @@ config DA9150_GPADC
		To compile this driver as a module, choose M here: the module will be
		called berlin2-adc.

		config ENVELOPE_DETECTOR
		tristate "Envelope detector using a DAC and a comparator"
		depends on OF
		help
		Say yes here to build support for an envelope detector using a DAC
		and a comparator.

		To compile this driver as a module, choose M here: the module will be
		called envelope-detector.

		config EXYNOS_ADC
		tristate "Exynos ADC driver support"
		depends on ARCH_EXYNOS \|\| ARCH_S3C24XX \|\| ARCH_S3C64XX \|\| (OF && COMPILE_TEST)

drivers/iio/adc/Makefile

+1 −0

Original line number	Diff line number	Diff line
		@@ -21,6 +21,7 @@ obj-$(CONFIG_BCM_IPROC_ADC) += bcm_iproc_adc.o
		obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o
		obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
		obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
		obj-$(CONFIG_ENVELOPE_DETECTOR) += envelope-detector.o
		obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
		obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
		obj-$(CONFIG_HI8435) += hi8435.o

drivers/iio/adc/envelope-detector.c

0 → 100644

+422 −0

Original line number	Diff line number	Diff line
		/*
		* Driver for an envelope detector using a DAC and a comparator
		*
		* Copyright (C) 2016 Axentia Technologies AB
		*
		* Author: Peter Rosin <peda@axentia.se>
		*
		* This program is free software; you can redistribute it and/or modify
		* it under the terms of the GNU General Public License version 2 as
		* published by the Free Software Foundation.
		*/

		/*
		* The DAC is used to find the peak level of an alternating voltage input
		* signal by a binary search using the output of a comparator wired to
		* an interrupt pin. Like so:
		* _
		* \| \
		* input +------>-------\|+ \
		* \| \
		* .-------. \| }---.
		* \| \| \| / \|
		* \| dac\|-->--\|- / \|
		* \| \| \|_/ \|
		* \| \| \|
		* \| \| \|
		* \| irq\|------<-------'
		* \| \|
		* '-------'
		*/

		#include <linux/completion.h>
		#include <linux/device.h>
		#include <linux/err.h>
		#include <linux/kernel.h>
		#include <linux/module.h>
		#include <linux/mutex.h>
		#include <linux/iio/consumer.h>
		#include <linux/iio/iio.h>
		#include <linux/iio/sysfs.h>
		#include <linux/interrupt.h>
		#include <linux/irq.h>
		#include <linux/of.h>
		#include <linux/of_device.h>
		#include <linux/platform_device.h>
		#include <linux/spinlock.h>
		#include <linux/workqueue.h>

		struct envelope {
		spinlock_t comp_lock; /* protects comp */
		int comp;

		struct mutex read_lock; /* protects everything else */

		int comp_irq;
		u32 comp_irq_trigger;
		u32 comp_irq_trigger_inv;

		struct iio_channel *dac;
		struct delayed_work comp_timeout;

		unsigned int comp_interval;
		bool invert;
		u32 dac_max;

		int high;
		int level;
		int low;

		struct completion done;
		};

		/*
		* The envelope_detector_comp_latch function works together with the compare
		* interrupt service routine below (envelope_detector_comp_isr) as a latch
		* (one-bit memory) for if the interrupt has triggered since last calling
		* this function.
		* The ..._comp_isr function disables the interrupt so that the cpu does not
		* need to service a possible interrupt flood from the comparator when no-one
		* cares anyway, and this ..._comp_latch function reenables them again if
		* needed.
		*/
		static int envelope_detector_comp_latch(struct envelope *env)
		{
		int comp;

		spin_lock_irq(&env->comp_lock);
		comp = env->comp;
		env->comp = 0;
		spin_unlock_irq(&env->comp_lock);

		if (!comp)
		return 0;

		/*
		* The irq was disabled, and is reenabled just now.
		* But there might have been a pending irq that
		* happened while the irq was disabled that fires
		* just as the irq is reenabled. That is not what
		* is desired.
		*/
		enable_irq(env->comp_irq);

		/* So, synchronize this possibly pending irq... */
		synchronize_irq(env->comp_irq);

		/* ...and redo the whole dance. */
		spin_lock_irq(&env->comp_lock);
		comp = env->comp;
		env->comp = 0;
		spin_unlock_irq(&env->comp_lock);

		if (comp)
		enable_irq(env->comp_irq);

		return 1;
		}

		static irqreturn_t envelope_detector_comp_isr(int irq, void *ctx)
		{
		struct envelope *env = ctx;

		spin_lock(&env->comp_lock);
		env->comp = 1;
		disable_irq_nosync(env->comp_irq);
		spin_unlock(&env->comp_lock);

		return IRQ_HANDLED;
		}

		static void envelope_detector_setup_compare(struct envelope *env)
		{
		int ret;

		/*
		* Do a binary search for the peak input level, and stop
		* when that level is "trapped" between two adjacent DAC
		* values.
		* When invert is active, use the midpoint floor so that
		* env->level ends up as env->low when the termination
		* criteria below is fulfilled, and use the midpoint
		* ceiling when invert is not active so that env->level
		* ends up as env->high in that case.
		*/
		env->level = (env->high + env->low + !env->invert) / 2;

		if (env->high == env->low + 1) {
		complete(&env->done);
		return;
		}

		/* Set a "safe" DAC level (if there is such a thing)... */
		ret = iio_write_channel_raw(env->dac, env->invert ? 0 : env->dac_max);
		if (ret < 0)
		goto err;

		/* ...clear the comparison result... */
		envelope_detector_comp_latch(env);

		/* ...set the real DAC level... */
		ret = iio_write_channel_raw(env->dac, env->level);
		if (ret < 0)
		goto err;

		/* ...and wait for a bit to see if the latch catches anything. */
		schedule_delayed_work(&env->comp_timeout,
		msecs_to_jiffies(env->comp_interval));
		return;

		err:
		env->level = ret;
		complete(&env->done);
		}

		static void envelope_detector_timeout(struct work_struct *work)
		{
		struct envelope *env = container_of(work, struct envelope,
		comp_timeout.work);

		/* Adjust low/high depending on the latch content... */
		if (!envelope_detector_comp_latch(env) ^ !env->invert)
		env->low = env->level;
		else
		env->high = env->level;

		/* ...and continue the search. */
		envelope_detector_setup_compare(env);
		}

		static int envelope_detector_read_raw(struct iio_dev *indio_dev,
		struct iio_chan_spec const *chan,
		int val, int val2, long mask)
		{
		struct envelope *env = iio_priv(indio_dev);
		int ret;

		switch (mask) {
		case IIO_CHAN_INFO_RAW:
		/*
		* When invert is active, start with high=max+1 and low=0
		* since we will end up with the low value when the
		* termination criteria is fulfilled (rounding down). And
		* start with high=max and low=-1 when invert is not active
		* since we will end up with the high value in that case.
		* This ensures that the returned value in both cases are
		* in the same range as the DAC and is a value that has not
		* triggered the comparator.
		*/
		mutex_lock(&env->read_lock);
		env->high = env->dac_max + env->invert;
		env->low = -1 + env->invert;
		envelope_detector_setup_compare(env);
		wait_for_completion(&env->done);
		if (env->level < 0) {
		ret = env->level;
		goto err_unlock;
		}
		*val = env->invert ? env->dac_max - env->level : env->level;
		mutex_unlock(&env->read_lock);

		return IIO_VAL_INT;

		case IIO_CHAN_INFO_SCALE:
		return iio_read_channel_scale(env->dac, val, val2);
		}

		return -EINVAL;

		err_unlock:
		mutex_unlock(&env->read_lock);
		return ret;
		}

		static ssize_t envelope_show_invert(struct iio_dev *indio_dev,
		uintptr_t private,
		struct iio_chan_spec const ch, char buf)
		{
		struct envelope *env = iio_priv(indio_dev);

		return sprintf(buf, "%u\n", env->invert);
		}

		static ssize_t envelope_store_invert(struct iio_dev *indio_dev,
		uintptr_t private,
		struct iio_chan_spec const *ch,
		const char *buf, size_t len)
		{
		struct envelope *env = iio_priv(indio_dev);
		unsigned long invert;
		int ret;
		u32 trigger;

		ret = kstrtoul(buf, 0, &invert);
		if (ret < 0)
		return ret;
		if (invert > 1)
		return -EINVAL;

		trigger = invert ? env->comp_irq_trigger_inv : env->comp_irq_trigger;

		mutex_lock(&env->read_lock);
		if (invert != env->invert)
		ret = irq_set_irq_type(env->comp_irq, trigger);
		if (!ret) {
		env->invert = invert;
		ret = len;
		}
		mutex_unlock(&env->read_lock);

		return ret;
		}

		static ssize_t envelope_show_comp_interval(struct iio_dev *indio_dev,
		uintptr_t private,
		struct iio_chan_spec const *ch,
		char *buf)
		{
		struct envelope *env = iio_priv(indio_dev);

		return sprintf(buf, "%u\n", env->comp_interval);
		}

		static ssize_t envelope_store_comp_interval(struct iio_dev *indio_dev,
		uintptr_t private,
		struct iio_chan_spec const *ch,
		const char *buf, size_t len)
		{
		struct envelope *env = iio_priv(indio_dev);
		unsigned long interval;
		int ret;

		ret = kstrtoul(buf, 0, &interval);
		if (ret < 0)
		return ret;
		if (interval > 1000)
		return -EINVAL;

		mutex_lock(&env->read_lock);
		env->comp_interval = interval;
		mutex_unlock(&env->read_lock);

		return len;
		}

		static const struct iio_chan_spec_ext_info envelope_detector_ext_info[] = {
		{ .name = "invert",
		.read = envelope_show_invert,
		.write = envelope_store_invert, },
		{ .name = "compare_interval",
		.read = envelope_show_comp_interval,
		.write = envelope_store_comp_interval, },
		{ /* sentinel */ }
		};

		static const struct iio_chan_spec envelope_detector_iio_channel = {
		.type = IIO_ALTVOLTAGE,
		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW)
		\| BIT(IIO_CHAN_INFO_SCALE),
		.ext_info = envelope_detector_ext_info,
		.indexed = 1,
		};

		static const struct iio_info envelope_detector_info = {
		.read_raw = &envelope_detector_read_raw,
		.driver_module = THIS_MODULE,
		};

		static int envelope_detector_probe(struct platform_device *pdev)
		{
		struct device *dev = &pdev->dev;
		struct iio_dev *indio_dev;
		struct envelope *env;
		enum iio_chan_type type;
		int ret;

		indio_dev = devm_iio_device_alloc(dev, sizeof(*env));
		if (!indio_dev)
		return -ENOMEM;

		platform_set_drvdata(pdev, indio_dev);
		env = iio_priv(indio_dev);
		env->comp_interval = 50; /* some sensible default? */

		spin_lock_init(&env->comp_lock);
		mutex_init(&env->read_lock);
		init_completion(&env->done);
		INIT_DELAYED_WORK(&env->comp_timeout, envelope_detector_timeout);

		indio_dev->name = dev_name(dev);
		indio_dev->dev.parent = dev;
		indio_dev->dev.of_node = dev->of_node;
		indio_dev->info = &envelope_detector_info;
		indio_dev->channels = &envelope_detector_iio_channel;
		indio_dev->num_channels = 1;

		env->dac = devm_iio_channel_get(dev, "dac");
		if (IS_ERR(env->dac)) {
		if (PTR_ERR(env->dac) != -EPROBE_DEFER)
		dev_err(dev, "failed to get dac input channel\n");
		return PTR_ERR(env->dac);
		}

		env->comp_irq = platform_get_irq_byname(pdev, "comp");
		if (env->comp_irq < 0) {
		if (env->comp_irq != -EPROBE_DEFER)
		dev_err(dev, "failed to get compare interrupt\n");
		return env->comp_irq;
		}

		ret = devm_request_irq(dev, env->comp_irq, envelope_detector_comp_isr,
		0, "envelope-detector", env);
		if (ret) {
		if (ret != -EPROBE_DEFER)
		dev_err(dev, "failed to request interrupt\n");
		return ret;
		}
		env->comp_irq_trigger = irq_get_trigger_type(env->comp_irq);
		if (env->comp_irq_trigger & IRQF_TRIGGER_RISING)
		env->comp_irq_trigger_inv \|= IRQF_TRIGGER_FALLING;
		if (env->comp_irq_trigger & IRQF_TRIGGER_FALLING)
		env->comp_irq_trigger_inv \|= IRQF_TRIGGER_RISING;
		if (env->comp_irq_trigger & IRQF_TRIGGER_HIGH)
		env->comp_irq_trigger_inv \|= IRQF_TRIGGER_LOW;
		if (env->comp_irq_trigger & IRQF_TRIGGER_LOW)
		env->comp_irq_trigger_inv \|= IRQF_TRIGGER_HIGH;

		ret = iio_get_channel_type(env->dac, &type);
		if (ret < 0)
		return ret;

		if (type != IIO_VOLTAGE) {
		dev_err(dev, "dac is of the wrong type\n");
		return -EINVAL;
		}

		ret = iio_read_max_channel_raw(env->dac, &env->dac_max);
		if (ret < 0) {
		dev_err(dev, "dac does not indicate its raw maximum value\n");
		return ret;
		}

		return devm_iio_device_register(dev, indio_dev);
		}

		static const struct of_device_id envelope_detector_match[] = {
		{ .compatible = "axentia,tse850-envelope-detector", },
		{ /* sentinel */ }
		};
		MODULE_DEVICE_TABLE(of, envelope_detector_match);

		static struct platform_driver envelope_detector_driver = {
		.probe = envelope_detector_probe,
		.driver = {
		.name = "iio-envelope-detector",
		.of_match_table = envelope_detector_match,
		},
		};
		module_platform_driver(envelope_detector_driver);

		MODULE_DESCRIPTION("Envelope detector using a DAC and a comparator");
		MODULE_AUTHOR("Peter Rosin <peda@axentia.se>");
		MODULE_LICENSE("GPL v2");