aboutsummaryrefslogtreecommitdiff
path: root/tcl/target/ti_dm365.cfg
blob: 8b52746bd12ea2e887541ea113d6774ab347d990 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
#
# Texas Instruments DaVinci family: TMS320DM365
#
if { [info exists CHIPNAME] } {
   set _CHIPNAME $CHIPNAME
} else {
   set _CHIPNAME dm365
}

# TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
# after JTAG reset until ICEpick is used to route them in.
set EMU01 "-disable"

# With EMU0/EMU1 jumpered *low* ARM and ETB are *enabled* without
# needing any ICEpick interaction.
#set EMU01 "-enable"

source [find target/icepick.cfg]

# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
if { [info exists ETB_TAPID] } {
   set _ETB_TAPID $ETB_TAPID
} else {
   set _ETB_TAPID 0x2b900f0f
}
jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0xf -expected-id $_ETB_TAPID $EMU01
jtag configure $_CHIPNAME.etb -event tap-enable \
	"icepick_c_tapenable $_CHIPNAME.jrc 1"

# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
if { [info exists CPU_TAPID] } {
   set _CPU_TAPID $CPU_TAPID
} else {
   set _CPU_TAPID 0x0792602f
}
jtag newtap $_CHIPNAME arm -irlen 4 -irmask 0xf -expected-id $_CPU_TAPID $EMU01
jtag configure $_CHIPNAME.arm -event tap-enable \
	"icepick_c_tapenable $_CHIPNAME.jrc 0"

# Primary TAP: ICEpick (JTAG route controller) and boundary scan
if { [info exists JRC_TAPID] } {
   set _JRC_TAPID $JRC_TAPID
} else {
   set _JRC_TAPID 0x0b83e02f
}
jtag newtap $_CHIPNAME jrc -irlen 6 -irmask 0x3f -expected-id $_JRC_TAPID

jtag configure $_CHIPNAME.jrc -event setup \
	"jtag tapenable $_CHIPNAME.etb; jtag tapenable $_CHIPNAME.arm"

################

# various symbol definitions, to avoid hard-wiring addresses
# and enable some sharing of DaVinci-family utility code
global dm365
set dm365 [ dict create ]

# Physical addresses for controllers and memory
# (Some of these are valid for many DaVinci family chips)
dict set dm365 sram0		0x00010000
dict set dm365 sram1		0x00014000
dict set dm365 sysbase		0x01c40000
dict set dm365 pllc1		0x01c40800
dict set dm365 pllc2		0x01c40c00
dict set dm365 psc		0x01c41000
dict set dm365 gpio		0x01c67000
dict set dm365 a_emif		0x01d10000
dict set dm365 a_emif_cs0	0x02000000
dict set dm365 a_emif_cs1	0x04000000
dict set dm365 ddr_emif		0x20000000
dict set dm365 ddr		0x80000000

source [find target/davinci.cfg]

################
# GDB target: the ARM, using SRAM1 for scratch.  SRAM0 (also 16K)
# and the ETB memory (4K) are other options, while trace is unused.
set _TARGETNAME $_CHIPNAME.arm

target create $_TARGETNAME arm926ejs -chain-position $_TARGETNAME

# NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel,
# and that the work area is used only with a kernel mmu context ...
$_TARGETNAME configure \
	-work-area-virt [expr 0xfffe0000 + 0x4000] \
	-work-area-phys [dict get $dm365 sram1] \
	-work-area-size 0x4000 \
	-work-area-backup 0

# be absolutely certain the JTAG clock will work with the worst-case
# CLKIN = 19.2 MHz (best case: 36 MHz) even when no bootloader turns
# on the PLL and starts using it.  OK to speed up after clock setup.
adapter speed 1500
$_TARGETNAME configure -event "reset-start" { adapter speed 1500 }

arm7_9 fast_memory_access enable
arm7_9 dcc_downloads enable

# trace setup
etm config $_TARGETNAME 16 normal full etb
etb config $_TARGETNAME $_CHIPNAME.etb