blob: ba1c3c563eec941a3f6cbe220ed78fcbda4a0b05 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
|
# SPDX-License-Identifier: GPL-2.0-or-later
# script for ATMEL sam3, a Cortex-M3 chip
#
# at91sam3u4e
# at91sam3u2e
# at91sam3u1e
# at91sam3u4c
# at91sam3u2c
# at91sam3u1c
#
# at91sam3s4c
# at91sam3s4b
# at91sam3s4a
# at91sam3s2c
# at91sam3s2b
# at91sam3s2a
# at91sam3s1c
# at91sam3s1b
# at91sam3s1a
#
# at91sam3A4C
# at91sam3A8C
# at91sam3X4C
# at91sam3X4E
# at91sam3X8C
# at91sam3X8E
# at91sam3X8H
source [find target/swj-dp.tcl]
if { [info exists CHIPNAME] } {
set _CHIPNAME $CHIPNAME
} else {
set _CHIPNAME sam3
}
if { [info exists ENDIAN] } {
set _ENDIAN $ENDIAN
} else {
set _ENDIAN little
}
# Work-area is a space in RAM used for flash programming
# By default use 64kB
if { [info exists WORKAREASIZE] } {
set _WORKAREASIZE $WORKAREASIZE
} else {
set _WORKAREASIZE 0x4000
}
#jtag scan chain
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
set _CPUTAPID 0x4ba00477
}
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
# 16K is plenty, the smallest chip has this much
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
$_TARGETNAME configure -event gdb-flash-erase-start {
halt
}
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
#
# Since we may be running of an RC oscilator, we crank down the speed a
# bit more to be on the safe side. Perhaps superstition, but if are
# running off a crystal, we can run closer to the limit. Note
# that there can be a pretty wide band where things are more or less stable.
adapter speed 500
adapter srst delay 100
if {[using_jtag]} {
jtag_ntrst_delay 100
}
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
# perform a soft reset
cortex_m reset_config sysresetreq
}
|
