1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
|
# DM355 EVM board
# http://focus.ti.com/docs/toolsw/folders/print/tmdsevm355.html
# http://c6000.spectrumdigital.com/evmdm355/
source [find target/ti_dm355.cfg]
reset_config trst_and_srst separate
# NOTE: disable or replace this call to dm355evm_init if you're
# debugging new UBL code from SRAM.
$_TARGETNAME configure -event reset-init { dm355evm_init }
#
# This post-reset init is called when the MMU isn't active, all IRQs
# are disabled, etc. It should do most of what a UBL does, except for
# loading code (like U-Boot) into DRAM and running it.
#
proc dm355evm_init {} {
global dm355
puts "Initialize DM355 EVM board"
# CLKIN = 24 MHz ... can't talk quickly to ARM yet
jtag_rclk 1500
########################
# PLL1 = 432 MHz (/8, x144)
# ...SYSCLK1 = 216 MHz (/2) ... ARM, MJCP
# ...SYSCLK2 = 108 MHz (/4) ... Peripherals
# ...SYSCLK3 = 27 MHz (/16) ... VPBE, DAC
# ...SYSCLK4 = 108 MHz (/4) ... VPSS
# pll1.{prediv,div1,div2} are fixed
# pll1.postdiv set in MISC (for *this* speed grade)
set addr [dict get $dm355 pllc1]
set pll_divs [dict create]
dict set pll_divs div3 16
dict set pll_divs div4 4
pll_v02_setup $addr 144 $pll_divs
# ARM is now running at 216 MHz, so JTAG can go faster
jtag_rclk 20000
########################
# PLL2 = 342 MHz (/8, x114)
# ....SYSCLK1 = 342 MHz (/1) ... DDR PHY at 171 MHz, 2x clock
# pll2.{postdiv,div1} are fixed
set addr [dict get $dm355 pllc2]
set pll_divs [dict create]
dict set pll_divs div1 1
dict set pll_divs prediv 8
pll_v02_setup $addr 114 $pll_divs
########################
# PINMUX
# All Video Inputs
davinci_pinmux $dm355 0 0x00007f55
# All Video Outputs
davinci_pinmux $dm355 1 0x00145555
# EMIFA (NOTE: more could be set up for use as GPIOs)
davinci_pinmux $dm355 2 0x00000c08
# SPI0, SPI1, UART1, I2C, SD0, SD1, McBSP0, CLKOUTs
davinci_pinmux $dm355 3 0x1bff55ff
# MMC/SD0 instead of MS; SPI0
davinci_pinmux $dm355 4 0x00000000
########################
# PSC setup (minimal)
# DDR EMIF/13, AEMIF/14, UART0/19
psc_enable 13
psc_enable 14
psc_enable 19
psc_go
########################
# DDR2 EMIF
# VTPIOCR impedance calibration
set addr [dict get $dm355 sysbase]
set addr [expr $addr + 0x70]
# clear CLR, LOCK, PWRDN; wait a clock; set CLR
mmw $addr 0 0x20c0
mmw $addr 0x2000 0
# wait for READY
while { [expr [mrw $addr] & 0x8000] == 0 } { sleep 1 }
# set IO_READY; then LOCK and PWRSAVE; then PWRDN
mmw $addr 0x4000 0
mmw $addr 0x0180 0
mmw $addr 0x0040 0
# NOTE: this DDR2 initialization sequence borrows from
# both UBL 1.50 and the SPRUEH7D DDR2 EMIF spec.
# reset (then re-enable) DDR controller
psc_reset 13
psc_go
psc_enable 13
psc_go
# now set it up for Micron MT47H64M16HR-37E @ 171 MHz
set addr [dict get $dm355 ddr_emif]
# DDRPHYCR1
mww [expr $addr + 0xe4] 0x50006404
# PBBPR -- burst priority
mww [expr $addr + 0x20] 0xfe
# SDCR -- unlock boot config; init for DDR2, relock, unlock SDTIM*
mmw [expr $addr + 0x08] 0x00800000 0
mmw [expr $addr + 0x08] 0x0013c632 0x03870fff
# SDTIMR, SDTIMR2
mww [expr $addr + 0x10] 0x2a923249
mww [expr $addr + 0x14] 0x4c17c763
# SDCR -- relock SDTIM*
mmw [expr $addr + 0x08] 0 0x00008000
# SDRCR -- refresh rate (171 MHz * 7.8usec)
mww [expr $addr + 0x0c] 1336
########################
# ASYNC EMIF
set addr [dict get $dm355 a_emif]
# slow/pessimistic timings
set nand_timings 0x40400204
# fast (25% faster page reads)
#set nand_timings 0x0400008c
# AWCCR
mww [expr $addr + 0x04] 0xff
# CS0 == socketed NAND (default MT29F16G08FAA, 2GByte)
mww [expr $addr + 0x10] $nand_timings
# CS1 == dm9000 Ethernet
mww [expr $addr + 0x14] 0x00a00505
# NANDFCR -- only CS0 has NAND
mww [expr $addr + 0x60] 0x01
# default: both chipselects to the NAND socket are used
nand probe 0
nand probe 1
########################
# UART0
set addr [dict get $dm355 uart0]
# PWREMU_MGNT -- rx + tx in reset
mww [expr $addr + 0x30] 0
# DLL, DLH -- 115200 baud
mwb [expr $addr + 0x20] 0x0d
mwb [expr $addr + 0x24] 0x00
# FCR - clear and disable FIFOs
mwb [expr $addr + 0x08] 0x07
mwb [expr $addr + 0x08] 0x00
# IER - disable IRQs
mwb [expr $addr + 0x04] 0x00
# LCR - 8-N-1
mwb [expr $addr + 0x0c] 0x03
# MCR - no flow control or loopback
mwb [expr $addr + 0x10] 0x00
# PWREMU_MGNT -- rx + tx normal, free running during JTAG halt
mww [expr $addr + 0x30] 0xe001
########################
# turn on icache - set I bit in cp15 register c1
mcr 15 0 0 1 0 0x00051078
}
# NAND -- socket has two chipselects, MT29F16G08FAA puts 1GByte on each one.
#
# NOTE: "hwecc4" here presumes that if you're using the standard 2GB NAND
# you either (a) have 'new' DM355 chips, with boot ROMs that don't need to
# use "hwecc4_infix" for the UBL; or else (b) aren't updating anything that
# needs infix layout ... like an old UBL, old U-Boot, old MVL kernel, etc.
set _FLASHNAME $_CHIPNAME.boot
nand device $_FLASHNAME davinci $_TARGETNAME 0x02000000 hwecc4 0x01e10000
set _FLASHNAME $_CHIPNAME.flash
nand device $_FLASHNAME davinci $_TARGETNAME 0x02004000 hwecc4 0x01e10000
# FIXME
# - support writing UBL with its header (new layout only with new ROMs)
# - support writing ABL/U-Boot with its header (new layout)
|
