Age | Commit message (Collapse) | Author | Files | Lines |
|
Add new chip info and tcl target
Change-Id: Ib9d33d1b145a8659857b7a6cc9c5acba047f41d1
Signed-off-by: Kyle Schwarz <zeranoe@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7081
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7f2 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
|
|
Change-Id: Iec5aba3a082f2e25f21d7ca173ed710894b370a4
Signed-off-by: Rocco Marco Guglielmi <roccomarco.guglielmi@gmail.com>
Change-Id: Ia83850e326661c8acb0712a280fdf961258322a4
Reviewed-on: https://review.openocd.org/c/openocd/+/7373
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
|
|
Fix typo in comments
Signed-off-by: George Voicu <razvanvg@hotmail.com>
Change-Id: Icc2d770e73f896e20dd347de324328030544bdb9
Reviewed-on: https://review.openocd.org/c/openocd/+/7333
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
The existing rp2040-core0.cfg configuration file was intended
for a special adapter which selects a SWD multidrop target on its own.
This means that rp2040-core0.cfg is totally unusable with a standard SWD
adapter.
To fix the problem, mark rp2040-core0.cfg as deprecated and
add rp2040.cfg, a basic config file with multidrop target selection.
Change-Id: I5194e42f529a2d9645481424b7c66ab61efa44ee
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7275
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
instrument "target/stm32x5x_common.cfg" used by both STM32L5x/U5x
to support HLA adapters like "interface/stlink.cfg" in non-secure mode
if the device switches to secure mode, the debug session will be
stopped immediately (with an explanatory message).
Change-Id: I645fdd55e3448ef82d0ddcc396f42fd7b2f39ac3
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Patrik Bachan <diggit@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/317/
Reviewed-on: https://review.openocd.org/c/openocd/+/6546
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
|
|
Some config changes required to run ESP32-S3 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I38022bb5ff5830e1cf9d11d6fe795ea99d91e9db
Reviewed-on: https://review.openocd.org/c/openocd/+/7254
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Some config changes required to run ESP32-S2 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie0a742442254ec6e95d4e05be40213b079a94dab
Reviewed-on: https://review.openocd.org/c/openocd/+/7253
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Some config changes required to run ESP32 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I484324f8497ec7934bb73164c638fc5f6460fcc4
Reviewed-on: https://review.openocd.org/c/openocd/+/7252
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
The work area should be backed up.
The flash probe runs an algorithm on the target CPU.
The flash is probed during gdb connect if gdb_memory_map is enabled
(is enabled by default).
Without backup the target memory gets corrupted on gdb connect.
Change-Id: I3344b9dc6cbf904d49f3b05ab104b541d1d63422
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7257
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
|
|
Since all the device definition when accessing device from jtag is also
valid when accessing from swd, lets make sure the configuration can
handle the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I5af071137fd8c3b52cc4ef72401f8eba952f9cad
Reviewed-on: https://review.openocd.org/c/openocd/+/7090
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
The STM32L5 and U5 devices have DBGMCU_CR trace related bits changed
wrt other STM32 devices.
Fix the setting in configuration script.
Change-Id: I0bbc48e7b1290b603c6966cf5ddd42df389e6ede
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7117
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Change-Id: I5cf3ab09dbf100d40ce40a4599cd8d2af18a5567
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/4574
Tested-by: jenkins
|
|
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Still some config file uses deprecated commands.
Replace them with the new commands.
Change-Id: I6ccbfb832e0ad2012e9af160bd2d92ad104af2bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7181
Tested-by: jenkins
|
|
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I97d0f01f342dddb31b2d454858fe854f002cf567
Reviewed-on: https://review.openocd.org/c/openocd/+/7077
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie1a56a398052f6f0e0eb2fe96777effeb59918f6
Reviewed-on: https://review.openocd.org/c/openocd/+/7076
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
- Config files for DAP/JTAG and DAP/SWD systems
- Xtensa core config definitions for NXP RT685 with Xtensa HiFi DSP
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I9c3280052073d86e09c7553de661eb8662a95c4a
Reviewed-on: https://review.openocd.org/c/openocd/+/7145
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Add new flash driver for internal flash of onsemi RSL10 device.
Valgrind-clean. Clang AddressSanitizer shows no errors.
Signed-off-by: Toms Stūrmanis <toms.sturmanis@gmail.com>
Change-Id: I8030542cb9805e94f56d7a69404cef5d88d6dd5a
Reviewed-on: https://review.openocd.org/c/openocd/+/7115
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
|
|
ARM semihosting + some custom syscalls implemented for
Espressif chips (ESP32, ESP32-S2, ESP32-S3)
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ic8174cf1cd344fa16d619b7b8405c9650e869443
Reviewed-on: https://review.openocd.org/c/openocd/+/7074
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
While reviewing on gerrit the change
https://review.openocd.org/6932/
it get clear that the missing documentation on stm32f4x's code
was triggering errors in the new change.
OpenOCD is currently unable to read traces, but these can be
hopefully be read with some other tool.
Document the settings for enabling trace on stm32[fl]4x.
Change-Id: Ibae77a53de16375d3d500e728678740095547009
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6945
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
|
|
With commit dc7b32ea4a00 ("armv7m_trace: get rid of the old tpiu
code") the target's event "trace-config" has been deprecated.
Create the TPIU device.
Replace the target's event "trace-config" with tpiu's event
"pre-enable" in the STM32 devices that require enabling the trace
clock _before_ programming the TPIU.
Make the script multi-instance-able in case it's used for JTAG
chained devices.
Uniform the code in STM32F4x with the other scripts.
Remove the empty event from STM32WLx.
Change-Id: Ifda219c3c5f37e03072a88168611cf505eb630b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
|
|
- Add new Xtensa TCL board files
- Add new Xtensa KC705 on-board FTDI interface
- Add new generic Xtensa and VDebug Xtensa target files
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I4acb15c83d1b7b8e6063833ce829530cb22a795e
Reviewed-on: https://review.openocd.org/c/openocd/+/7083
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Add linuxgpiod cfg for Aspeed AST2600 for a case if JTAG master needs
to be implemented using linuxgpiod intead of hardware JTAG master mode.
These AST2600 GPIOs will be mapped to JTAG/SWD signals.
+-----------+-------------+-------------+
| signal | GPIO name | gpio offset |
+-----------+-------------+-------------+
| TCK/SWCLK | GPIOI2 | 66 |
| TMS/SWDIO | GPIOI3 | 67 |
| TDI | GPIOI1 | 65 |
| TDO | GPIOI4 | 68 |
| nTRST | GPIOI0 | 64 |
+-----------+-------------+-------------+
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Change-Id: I19278402b0895be12d38c0ecea8fdbc56fd491b8
Reviewed-on: https://review.openocd.org/c/openocd/+/7112
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
|
|
Add support for Lattice MachXO3 FPGA family.
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Change-Id: I01fcec0ee458e809246e4505019d15047655dd47
Reviewed-on: https://review.openocd.org/c/openocd/+/7113
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
This patch adds support for DAP interface to Cadence vdebug driver.
It implements a new transport layer for dapdirect_swd.
Change-Id: I64b02a9e1ce91e552e07fca692879655496f88b6
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6965
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
ngultra is a Quad-R52 SoC + an FPGA.
Signed-off-by: Adrien Grassein <agrassein@nanoxplore.com>
Change-Id: I6a04eab3d9a7610e9dfa3d9f647868e579b6bd8a
Reviewed-on: https://review.openocd.org/c/openocd/+/7046
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Memory protection must be disabled to allow stub flasher
operate correctly.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I6f292ee672ae001cd6e4df5d24eb7bb862639093
Reviewed-on: https://review.openocd.org/c/openocd/+/7037
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Memory protection must be disabled to allow stub flasher
operate correctly.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I2f239d98fca6882c4361691af306a5652b58ee78
Reviewed-on: https://review.openocd.org/c/openocd/+/7036
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
This driver is used with the ESP32 chips which has builtin USB-JTAG
interface. e.g. with ESP32-C3, ESP32-S3
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: If966268cb8d26f76540dd5440245a17ed0b72c61
Reviewed-on: https://review.openocd.org/c/openocd/+/6943
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
|
|
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ief3da306a6e1978de7dfb8f552f9ff23151f9944
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7030
Tested-by: jenkins
|
|
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/interface | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7bd6a628e9e153fc477cddf9b97087a39ec48aa7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7029
Tested-by: jenkins
|
|
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/board | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ibcf7da62e842aafd036a78db9ea2b9f11f79af16
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7028
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
|
|
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/ target| while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7b2610300b24cccd07bfa6fb5f1266970d5d3a1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7027
Tested-by: jenkins
|
|
The SPDX tag is aimed at machine handling and it's thus expected
to be placed in the first line.
Change-Id: I3992856eeb28b333c38d010ef286e22471ede263
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7026
Tested-by: jenkins
|
|
OpenOCD project is switching to SPDX tags.
Replace the few FSF boilerplate in tcl folder.
Change-Id: I15b146eb77cc491ed7355178f684f3e76fc763b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7025
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
|
|
Remove trailing '.'
While there, add newline to file's last line.
Change-Id: I3a727e406b572d051b28e17688c24627e55520c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7024
Tested-by: jenkins
|
|
Change-Id: I83d2477e8bc837aeac69bd5d08fdd923fd00a37c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7023
Tested-by: jenkins
|
|
In order to facilitate debugging multiple cores, specify the coreid and
the hwthread rtos in the imx8m target configuration.
Change-Id: Ibd871517a160ceca15002fb10e27cb793f14d086
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-on: https://review.openocd.org/c/openocd/+/7019
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
ESP32-S3 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794
Reviewed-on: https://review.openocd.org/c/openocd/+/6990
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
Add Ampere Altra ("Quicksilver") and Ampere Altra Max ("Mystique")
target/board configuration files.
The target configuration file supports silicon and emulation.
The board configuration files support 1 and 2 socket platforms.
Tested on Ampere emulation and silicon
Change-Id: I036c798a50624e30ab51ccd2895b6f60c40be096
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5591
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
|
|
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I21506526e3ebd9c3a70a25ba60bf83aee431feb6
Reviewed-on: https://review.openocd.org/c/openocd/+/7016
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
ESP32-S2 is a single core Xtensa chip.
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I2fb32978e801af5aa21616c581691406ad7cd6bb
Reviewed-on: https://review.openocd.org/c/openocd/+/6940
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
|
|
This commit is adapted from [1].
[1] https://review.openocd.org/c/openocd/+/4999
Signed-off-by: Michael Walle <michael.walle@kontron.com>
Signed-off-by: Heiko Thiery <heiko.thiery@kontron.com>
[ adapted to use common configuration ]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9a428371694e7864e03055b8de18a55a7843b8c2
Reviewed-on: https://review.openocd.org/c/openocd/+/6977
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|
|
The LS1028A is similar to the LS1088A, except that it has 2 CPUs (and
different ethernet capabilities). From a JTAG perspective, all that's
different is the number of CPUs and the TAPID.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Iba3a0ecfbf82cfcfeb7eea42d52121c3b9dc93a2
Reviewed-on: https://review.openocd.org/c/openocd/+/6976
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
|