aboutsummaryrefslogtreecommitdiff
path: root/tcl/interface
AgeCommit message (Collapse)AuthorFilesLines
2017-05-31imx_gpio: add mmap based jtag interface for IMX processorsGrzegorz Kostka1-0/+35
For some targets (like nrf51) sysfs driver is too slow. This patch implements memory maped driver for IMX processors. Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should work on any NXP IMX CPU. Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7 Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com> Reviewed-on: http://openocd.zylin.com/4106 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2017-05-12jtag/drivers: Add Cypress KitProg driverForest Crossman1-0/+12
This patch adds a driver for the SWD-only Cypress KitProg programmer/debugger. Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5 Signed-off-by: Forest Crossman <cyrozap@gmail.com> Reviewed-on: http://openocd.zylin.com/3221 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2017-04-23added interface config file for In-Circuit's ICprog OpenOCD JTAG adapterMatthias Bock1-0/+14
Change-Id: I9f9758d3a30bbcca9f750f604e011e5cc25809c5 Signed-off-by: Matthias Bock <mail@matthiasbock.net> Reviewed-on: http://openocd.zylin.com/4107 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2016-11-06Remove support for the GPL incompatible FTDI D2XX libraryAndreas Fritiofson1-2/+2
Convert Presto, OpenJTAG and USB-Blaster (I) adapter drivers to libftdi only. Change-Id: Ib28887620a3dcbb754b9dbf87b9731acca3ac600 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/3237 Tested-by: jenkins Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-11-06Remove since long deprecated ft2232 driverAndreas Fritiofson51-633/+0
Purge all legacy interface configurations so there's no more confusion over which one to use. Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just duplicates what INSTALL says. Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/3236 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-08-14interface: Add XDS100v3 support.Remco Bloemen1-0/+11
XDS100v3 is software compatible with the XDS100v2, but has a different usb pid. This commit adds `xds100v3.cfg` that sources the v2 one and changes the usb pid. Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80 Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com> Reviewed-on: http://openocd.zylin.com/3632 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14tcl/interface/ftdi: add config for the MBFTDI adapterAntony Pavlov1-0/+16
MBFTDI is a very cheap FT2232-based JTAG adapter for programming Marsohod FPGA board. Please see http://www.marsohod.org/prodmbftdi for details. Change-Id: I35f758b49d1566098dc27f9581829cccad93ceeb Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-on: http://openocd.zylin.com/3604 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-04-12interface/jlink: Fix comment about serial numberMarc Schink1-10/+5
Leading zeros for the serial number are not necessary anymore. Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Change-Id: Ie4ff47b9cda7ccf314c6fda9a2784947db5ee4d9 Reviewed-on: http://openocd.zylin.com/3401 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-02-13add Digilent HS2 supportAndrew Kohlsmith1-0/+10
Change-Id: If506c33f22d95f4c47f30c4348d461197c976fdd Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/3160 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2016-02-03tcl: Support for the miniSpartan6+ board.Tim 'mithro' Ansell1-0/+15
* https://www.scarabhardware.com/minispartan6/ * https://github.com/scarabhardware/miniSpartan6-plus/raw/master/miniSpartan6%2B_Rev_B.pdf The miniSpartan6+ board is wired identically to the Pipistrello device but sadly doesn't have a custom device description. Change-Id: I07fd57b1ec87d72edf68860684928a3781e2f08a Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com> Reviewed-on: http://openocd.zylin.com/3117 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-11-16tcl/interface/ftdi: add 100ask's OpenJTAG configPaul Fertser1-0/+16
Schematics provided by Matthias Bock. Change-Id: I3d00453fece3b4df58a53bee21fff646a8b71a34 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2718 Tested-by: jenkins
2015-11-13topic: Interface config file for FTDI UM232H moduleRagnar Sundblad1-0/+35
Added interface config file for the FTDI FT232H based UM232H module. This should work with UM232H-B too, an even cheaper module, but that has not been tested. Change-Id: Ifc312d6741da0b7862fe07d854023190d7afe251 Signed-off-by: Ragnar Sundblad <raggesu@gmail.com> Reviewed-on: http://openocd.zylin.com/3031 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2015-10-21tcl: Setting lowlevel driver for ixo-usb-jtagTim 'mithro' Ansell1-3/+31
Also add further documentation about the project and how to use it. Change-Id: Ia9878de566b3c8c1ea29f129287d5aea904d861d Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com> Reviewed-on: http://openocd.zylin.com/2961 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-09-30tcl/interface/ftdi: Add Digilent JTAG-HS3 configAndreas Färber1-0/+13
Derived from tcl/interface/digilent-hs1.cfg. JTAG-HS3 has an open drain buffer on pin 14 for SRST to work with PS_SRST_B on Xilinx Zynq SoC. Change-Id: I1e9e72d0511528a61207e318aff937ae9fad5bf9 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/2728 Tested-by: jenkins Reviewed-by: Robert Jordens <jordens@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-08-06bcm2835gpio: Add SWD support, Raspberry Pi 2 support.Christoph Pittracher2-0/+44
Added support for SWD transport similar to sysfsgpio driver. Added configurable peripheral base address to support Raspberry Pi 2. Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04 Signed-off-by: Christoph Pittracher <pitt@segfault.info> Reviewed-on: http://openocd.zylin.com/2802 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-08-06kc705: digilent-jtag/kintex7/jtagspi boardRobert Jordens1-0/+11
Xilinx Kintex7 Development board with integrated Digilent JTAG-SMT1 (a.k.a. HS1) interface and a 128 MBit SPI flash. Change-Id: I9daba0a2fb2c17e04bcb37bd41872ebde25e0d2f Signed-off-by: Robert Jordens <jordens@gmail.com> Reviewed-on: http://openocd.zylin.com/2861 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-08-06pipistrello: ftdi-jtag/spartan6/jtagspi boardRobert Jordens1-0/+13
The Pipistrello is a low cost FPGA board with a Xilinx Spartan6 LX45, a SPI flash and onboard FTDI JTAG. This board is a good example use case for the jtagspi flash driver talking through a proxy bitstream. Change-Id: I04a80610ff825c36ebcb67b879507028eed141ad Signed-off-by: Robert Jordens <jordens@gmail.com> Reviewed-on: http://openocd.zylin.com/2846 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-04-14turtelizer2-revC: Tested with real hardware.Uwe Bonnes2-5/+4
Also some hints around deprecated tcl/interface/turtelizer2.cfg added. Change-Id: Ifa57b49febffaeddd5d8ff0a48833d3544927b10 Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de> Reviewed-on: http://openocd.zylin.com/2584 Tested-by: jenkins Reviewed-by: Harald Kipp Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-04-14tcl/interface/parport: default to sane value on non-windows systemsPaul Fertser1-1/+5
When using ppdev driver 0 is the most appropriate default value as it corresponds to /dev/parport0. Raw port address is suitable only for direct access (I think that's parport-giveio on windows). Reported by danitool on IRC. Change-Id: I983c22251de6601b433ad31aaf660fb664cee7e9 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2572 Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-03-09tcl/interface/ftdi/xdsv2: fix and clarify EMU* signalsMatthijs van Duin1-3/+42
The signal names are changed for consistency with TI's docs and sources. Change-Id: Ic5c5314daa20f6f610be8a848399f951d47aa137 Signed-off-by: Matthijs van Duin <matthijs@rinnic-vaude.nl> Reviewed-on: http://openocd.zylin.com/2231 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-02-22cfg: add board and target configs for TI SimpleLink Wi-Fi CC3200 LaunchPadPaul Fertser1-0/+15
Change-Id: I4396ee737c1dad380aa23894bbd1faf75f26d072 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2465 Tested-by: jenkins
2015-02-11tcl/interface/ftdi: correct LED config for BusBlaster KT-LinkAnton Kuzmin1-1/+1
Configure the LED to be off by default, blink on activity. Change-Id: I8515ee66c49bddf866268b85811be15c2dbc086c Signed-off-by: Anton Kuzmin <anton.kuzmin@cs.fau.de> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2539 Tested-by: jenkins
2015-02-11J-Link serial number config optionJoerg Fischer1-0/+11
Add serial option to jlink config commands, handy when there is more than one adapter connected. To select adapter 0123456 for OpenOCD, use jlink serial 0123456 Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee Signed-off-by: Joerg Fischer <turboj@gmx.de> Reviewed-on: http://openocd.zylin.com/2521 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-01-15tcl/interface/ftdi: add config for the IoT-LAB adapterPaul Fertser1-0/+11
This is an integrated adapter used on the IoT-LAB boards. Schematics are available from https://github.com/iot-lab/iot-lab/wiki/Docs/openm3-schematics.pdf Change-Id: I1c80e72653c3f319bb04d01e3dfddb1c2447c398 Tested-by: Quentin Lampin <quentin.lampin@orange.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2415 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-11-02tcl/interface/ftdi/swd-resistor-hack: clarify and add schematic diagramPaul Fertser1-0/+17
Change-Id: I8600ee983de85e4225430ae508a50cd938122d89 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2357 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-10-16cmsis-dap: add serial number supportSpencer Oliver1-0/+3
Change-Id: I66926d1013e2b3a43ce0d18d3599771428706b6a Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2329 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-10-06interface/ftdi/olimex-arm-usb-ocd-h: fix nTRST control definitionPaul Fertser1-2/+2
According to my inspection of an Olimex ARM-USB-OCD-H adapter ACBUS0 is connected directly to an SN74LVC2T45 buffer input B2, and the corresponding output A2 is connected directly to the JTAG connector. It seems the information in the Olimex flyer is incorrect for the -H version and TRST can't be tri-stated, ACBUS2 is unused. The older ARM-USB-OCD device has SN74AC244 for an output buffer and ACBUS2 controls its !2OE, ACBUS0 connected to 2A1 (2Y1 is nTRST), in accordance with the information flyer. Change-Id: I22828b7b959b6f62c3f51367feb8fab9705641e5 Reported-by: Tim Sander <tim@krieglstein.org> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2286 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Tim Sander <tim@krieglstein.org>
2014-09-22Support hla_serial command for ST-LINK adapters.Austin Phillips2-0/+14
The hla_serial command allows for a programming device serial number to be specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2 programmers to be attached to a single machine and operated using openocd. Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791 Signed-off-by: Austin Phillips <austin_phillips@hotmail.com> Reviewed-on: http://openocd.zylin.com/2198 Tested-by: jenkins Reviewed-by: Martin Glunz <mg@wunderkis.de> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-09-11tcl/interface/ftdi/sheevaplug: fix device descriptionPaul Fertser1-6/+1
Without this SheevaPlug debugging interface can't be matched. Change-Id: Ifca149130d03c1aa165ed1123e8540e49485f023 Reported-by: Andreas Schneider <schneider.andi@gmail.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2265 Tested-by: jenkins
2014-09-08tcl/interface/ftdi: fix TRST for Olimex TINY adaptersPaul Fertser2-4/+4
According to the research by Eldar, TINY-H adapter has nTRST connected to ACBUS0 directly via a 100 Ohms series resistor. I think it's safe to assume the older TINY adapter does the same. See high-res photos at [1]. This patch should fix issues with JTAG for the case when nTRST is actually connected but is missing from the config. [1] https://wikidevi.com/wiki/Olimex_ARM-USB-TINY-H Change-Id: Iaaee7be30536ebb502802d38b82cd9573408f854 Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2247 Tested-by: jenkins Reviewed-by: demokmail <demokmail@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-09-08tcl/interface/ftdi: add kt-link config (with SWD) for DP BusBlasterPaul Fertser2-0/+24
Change-Id: Icbeca8c0c3845c0b777fb2e4c81b17e7b7cc5ff8 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2269 Tested-by: jenkins Reviewed-by: Ben Gamari <bgamari@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-08-19tcl/interface/ftdi: auto-select SWD from converters' configsPaul Fertser3-0/+6
When you source a JTAG-SWD converter config, any other transport doesn't make any sense, so just autoselect it right there. Change-Id: I6c098740905a0d4007473fc19cc07e11cbcc9369 Suggested-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2248 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
2014-08-04interface/ftdi: Mark flyswatter.cfg as testedAndreas Fritiofson1-5/+0
- Flyswatter + Proxmark3 (Atmel AT91SAM7S256) - works - Flyswatter + Tiva Launchpad (EK-TM4C123GXL) - works Change-Id: I615e0ff9262be6ae1064fb2de8e6e810775e7db4 Tested-by: Ondrej Mikle <ondrej.mikle@nic.cz> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2237 Tested-by: jenkins
2014-06-28cfg: add SWD configs for stellaris ftdi based adaptersSpencer Oliver3-0/+6
Tested on hardware. Change-Id: Ib0191e97988dc79e9a62da74bd7fe25f548ff5a2 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2185 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Tested-by: jenkins
2014-06-28tcl/interface/ftdi: add SWD configs for kt-link, olimex, rowley and resistor ↵Paul Fertser4-0/+24
hack Resistor hack is runtime-tested, other configs are based on schematics. Change-Id: I8daffa0434cd41d142fbec7c230a302284f7aa31 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2184 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2014-06-28jtag/drivers/ftdi: require defining SWD_EN signal for SWD modePaul Fertser1-1/+1
Use a special signal instead of a dedicated swd mask. Amend jtag-lock-pick_tiny_2 config accordingly. Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2183 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2014-06-28cfg: Add SWD support to JTAG-lock-pick Tiny 2Andreas Fritiofson1-0/+2
Change-Id: I61eac507fa6861b7daf603ebca58e8bf3cc699c1 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2136 Tested-by: jenkins Reviewed-by: Jens Bauer <jens@gpio.dk> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-03-17tcl/interface/ftdi: add Digilent JTAG-SMT2 configPaul Fertser1-0/+17
Tested on ZedBoard by Tim Sander. Change-Id: I4316d9b4d36f01bbe91a46c78ea8bca22efb1a5a Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2029 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-17stlink_usb.c: add support for STLink V2-1Bartosz Bielawski1-0/+9
The new version of STLink (V2-1) has a different USB endpoint layout. As the PID of the device also changed it's possible to change EPs used by OpenOCD in runtime. The patch adds three new fields to stlink_usb_handle_s and assigns right EP numbers in stlink_usb_open(). Parts of the code inspired by and used with consent of Jens Hoffmann. Change-Id: I93b69fb889f15317e9bf864905f435905db39745 Signed-off-by: Bartosz Bielawski <bartosz.bielawski@gmail.com> Reviewed-on: http://openocd.zylin.com/2019 Tested-by: jenkins Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-09interface/ftdi/xds100v2.cfg: Add another VID/PID, drop descTom Rini1-2/+1
The XDS100v2 is often embedded in a number of platforms using the VID/PID of 0x0403/0x6010 and a generic FTDI device description. Add this VID/PID combination and remove the description line. Change-Id: I370e6199ac24f802426e9541e19ee38f18f1209a Signed-off-by: Tom Rini <trini@ti.com> Reviewed-on: http://openocd.zylin.com/2016 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-02-11interface/ftdi/xds100v2.cfg: default to reset state and ask user to release ↵Paul Fertser1-1/+3
it later This adapter is special and needs a reset sequence to be performed before operation. Since there're no suitable hooks to do that, we have no choice but to ask the user to manually add the necessary commands to his or her config file. Change-Id: I48fb4276e77529768266840221b68c3ae26801e1 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1884 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-02-04interface/ftdi: add TUMPA Lite configPaul Fertser1-0/+12
TUMPA Lite is a cheap FT232H-based breakout board, without any buffering. It also lacks series resistors so for some targets (especially when not using ridiculously short wires) one needs to add about 47 Ohms in series on every high-speed line. The SRST line is connected directly to the FT232H too. Real-life tested (including SRST and TRST). Change-Id: I5ed4f88d8d20384e9c52efe2ff0c290e2650d43e Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1918 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-01-20jtag/drivers: add USB-Blaster IIFranck Jullien1-0/+8
This patchs adds a new access driver for the existing USB-Blaster interface driver. This interface (as it is build-in on the sockit development board) is composed of a Cypress EZ-USB plus a CPLD. The Cypress chip as an embedded 8051 microcontroller. When it's powered up, the firmware is downloaded to the chip then the device is disconnected and reconnected with the new firmware. The USB-Blaster II protocol is almost identicial to the old one. The only difference is that you need to send a 0x5F before read TDO back. This command seems to copy TDO buffer datas to the endpoint buffer. Driver will be auto enabled if libusb-1.0 is detected. Change-Id: I562a720a68cb4dcabeab791947d5d38776cb70fa Signed-off-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-on: http://openocd.zylin.com/1791 Tested-by: jenkins Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-01-09cmsis-dap: add initial cmsis-dap supportSpencer Oliver1-0/+7
This is based on work from: https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap Main changes include moving over to using HIDAPI rather than libusb-1.0 and cleaning up to merge into master. Support for reset using srst has also been added. It has been tested on all the mbed boards as well as the Freedom board from Freescale. These boards only implement SWD mode, however JTAG mode has been tested with a Keil ULINK2 and a stm32 target - but requires a lot more work. Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com> Reviewed-on: http://openocd.zylin.com/1542 Tested-by: jenkins
2013-12-31jtag_vpi: make the server address configurableFranck Jullien1-2/+10
Change-Id: I58e89c789b79ffb0b54ef94d208be876c271ddf7 Signed-off-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-on: http://openocd.zylin.com/1840 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-12-14ftdi/neodb.cfg: mark as testedPaul Fertser1-5/+0
Working against openmoko gta02 target, including TRST and SRST (the stupid samsung chip fully resets under trst, so it's actually of little use here). Change-Id: I831124659fc12efbccef536f07d15509c2112f92 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1814 Tested-by: jenkins Reviewed-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-10-31ftdi/tumpa.cfg: enable proper output buffer control, add another USB IDPaul Fertser1-2/+2
The schematics used for writing the config file were incorrect, real hardware needs ACBUS3 _low_ as it's connected directly to the output buffer's !OE pin. Also apparently sometimes TUMPA comes with default FTDI IDs. Real-life tested (including TRST and SRST) with a custom stm32f103 board, thanks to Mike Wang for the adapter sample. Change-Id: Iab566e6d14f8392030f6ff2c8d976e1b57cf5ce6 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1789 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-09-08jtag: drivers: Add JTAP VPI client driverFranck Jullien1-0/+10
This patch adds a driver for the jtag_vpi server [1]. This server is now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC). The jtag_vpi server provides an interface between OpenOCD and a simulated core. [1] http://github.com/fjullien/jtag_vpi Change-Id: I717b72cace4845f66c878581345074f99002e21a Signed-off-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-on: http://openocd.zylin.com/1609 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-08-29Added new ftdi interface devicePushpal Sidhu1-0/+26
Added new configuration file for gw16042 device. Also added this to interface/ftdi examples in documentation. Change-Id: I07bb10bfc79a5d13007288cd57f254d889075214 Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> Reviewed-on: http://openocd.zylin.com/1563 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-08-15interface/ftdi/tumpa: remove ftdi_device_desc as it's incorrectPaul Fertser1-1/+0
The end users on IRC report that actual USB device has different information in its descriptor so it doesn't match. Remove it altogether. Change-Id: Id7841667390a514581e630e67b9283675803135b Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1548 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
generated by cgit v1.1 at 2024-11-16 13:27:22 +0000