aboutsummaryrefslogtreecommitdiff
path: root/tcl/interface
AgeCommit message (Collapse)AuthorFilesLines
2014-08-19tcl/interface/ftdi: auto-select SWD from converters' configsPaul Fertser3-0/+6
When you source a JTAG-SWD converter config, any other transport doesn't make any sense, so just autoselect it right there. Change-Id: I6c098740905a0d4007473fc19cc07e11cbcc9369 Suggested-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2248 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
2014-08-04interface/ftdi: Mark flyswatter.cfg as testedAndreas Fritiofson1-5/+0
- Flyswatter + Proxmark3 (Atmel AT91SAM7S256) - works - Flyswatter + Tiva Launchpad (EK-TM4C123GXL) - works Change-Id: I615e0ff9262be6ae1064fb2de8e6e810775e7db4 Tested-by: Ondrej Mikle <ondrej.mikle@nic.cz> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2237 Tested-by: jenkins
2014-06-28cfg: add SWD configs for stellaris ftdi based adaptersSpencer Oliver3-0/+6
Tested on hardware. Change-Id: Ib0191e97988dc79e9a62da74bd7fe25f548ff5a2 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/2185 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Tested-by: jenkins
2014-06-28tcl/interface/ftdi: add SWD configs for kt-link, olimex, rowley and resistor ↵Paul Fertser4-0/+24
hack Resistor hack is runtime-tested, other configs are based on schematics. Change-Id: I8daffa0434cd41d142fbec7c230a302284f7aa31 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2184 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2014-06-28jtag/drivers/ftdi: require defining SWD_EN signal for SWD modePaul Fertser1-1/+1
Use a special signal instead of a dedicated swd mask. Amend jtag-lock-pick_tiny_2 config accordingly. Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2183 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2014-06-28cfg: Add SWD support to JTAG-lock-pick Tiny 2Andreas Fritiofson1-0/+2
Change-Id: I61eac507fa6861b7daf603ebca58e8bf3cc699c1 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2136 Tested-by: jenkins Reviewed-by: Jens Bauer <jens@gpio.dk> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2014-03-17tcl/interface/ftdi: add Digilent JTAG-SMT2 configPaul Fertser1-0/+17
Tested on ZedBoard by Tim Sander. Change-Id: I4316d9b4d36f01bbe91a46c78ea8bca22efb1a5a Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2029 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-17stlink_usb.c: add support for STLink V2-1Bartosz Bielawski1-0/+9
The new version of STLink (V2-1) has a different USB endpoint layout. As the PID of the device also changed it's possible to change EPs used by OpenOCD in runtime. The patch adds three new fields to stlink_usb_handle_s and assigns right EP numbers in stlink_usb_open(). Parts of the code inspired by and used with consent of Jens Hoffmann. Change-Id: I93b69fb889f15317e9bf864905f435905db39745 Signed-off-by: Bartosz Bielawski <bartosz.bielawski@gmail.com> Reviewed-on: http://openocd.zylin.com/2019 Tested-by: jenkins Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp> Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-03-09interface/ftdi/xds100v2.cfg: Add another VID/PID, drop descTom Rini1-2/+1
The XDS100v2 is often embedded in a number of platforms using the VID/PID of 0x0403/0x6010 and a generic FTDI device description. Add this VID/PID combination and remove the description line. Change-Id: I370e6199ac24f802426e9541e19ee38f18f1209a Signed-off-by: Tom Rini <trini@ti.com> Reviewed-on: http://openocd.zylin.com/2016 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-02-11interface/ftdi/xds100v2.cfg: default to reset state and ask user to release ↵Paul Fertser1-1/+3
it later This adapter is special and needs a reset sequence to be performed before operation. Since there're no suitable hooks to do that, we have no choice but to ask the user to manually add the necessary commands to his or her config file. Change-Id: I48fb4276e77529768266840221b68c3ae26801e1 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1884 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2014-02-04interface/ftdi: add TUMPA Lite configPaul Fertser1-0/+12
TUMPA Lite is a cheap FT232H-based breakout board, without any buffering. It also lacks series resistors so for some targets (especially when not using ridiculously short wires) one needs to add about 47 Ohms in series on every high-speed line. The SRST line is connected directly to the FT232H too. Real-life tested (including SRST and TRST). Change-Id: I5ed4f88d8d20384e9c52efe2ff0c290e2650d43e Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1918 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-01-20jtag/drivers: add USB-Blaster IIFranck Jullien1-0/+8
This patchs adds a new access driver for the existing USB-Blaster interface driver. This interface (as it is build-in on the sockit development board) is composed of a Cypress EZ-USB plus a CPLD. The Cypress chip as an embedded 8051 microcontroller. When it's powered up, the firmware is downloaded to the chip then the device is disconnected and reconnected with the new firmware. The USB-Blaster II protocol is almost identicial to the old one. The only difference is that you need to send a 0x5F before read TDO back. This command seems to copy TDO buffer datas to the endpoint buffer. Driver will be auto enabled if libusb-1.0 is detected. Change-Id: I562a720a68cb4dcabeab791947d5d38776cb70fa Signed-off-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-on: http://openocd.zylin.com/1791 Tested-by: jenkins Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2014-01-09cmsis-dap: add initial cmsis-dap supportSpencer Oliver1-0/+7
This is based on work from: https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap Main changes include moving over to using HIDAPI rather than libusb-1.0 and cleaning up to merge into master. Support for reset using srst has also been added. It has been tested on all the mbed boards as well as the Freedom board from Freescale. These boards only implement SWD mode, however JTAG mode has been tested with a Keil ULINK2 and a stm32 target - but requires a lot more work. Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com> Reviewed-on: http://openocd.zylin.com/1542 Tested-by: jenkins
2013-12-31jtag_vpi: make the server address configurableFranck Jullien1-2/+10
Change-Id: I58e89c789b79ffb0b54ef94d208be876c271ddf7 Signed-off-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-on: http://openocd.zylin.com/1840 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-12-14ftdi/neodb.cfg: mark as testedPaul Fertser1-5/+0
Working against openmoko gta02 target, including TRST and SRST (the stupid samsung chip fully resets under trst, so it's actually of little use here). Change-Id: I831124659fc12efbccef536f07d15509c2112f92 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1814 Tested-by: jenkins Reviewed-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-10-31ftdi/tumpa.cfg: enable proper output buffer control, add another USB IDPaul Fertser1-2/+2
The schematics used for writing the config file were incorrect, real hardware needs ACBUS3 _low_ as it's connected directly to the output buffer's !OE pin. Also apparently sometimes TUMPA comes with default FTDI IDs. Real-life tested (including TRST and SRST) with a custom stm32f103 board, thanks to Mike Wang for the adapter sample. Change-Id: Iab566e6d14f8392030f6ff2c8d976e1b57cf5ce6 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1789 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-09-08jtag: drivers: Add JTAP VPI client driverFranck Jullien1-0/+10
This patch adds a driver for the jtag_vpi server [1]. This server is now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC). The jtag_vpi server provides an interface between OpenOCD and a simulated core. [1] http://github.com/fjullien/jtag_vpi Change-Id: I717b72cace4845f66c878581345074f99002e21a Signed-off-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-on: http://openocd.zylin.com/1609 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-08-29Added new ftdi interface devicePushpal Sidhu1-0/+26
Added new configuration file for gw16042 device. Also added this to interface/ftdi examples in documentation. Change-Id: I07bb10bfc79a5d13007288cd57f254d889075214 Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> Reviewed-on: http://openocd.zylin.com/1563 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-08-15interface/ftdi/tumpa: remove ftdi_device_desc as it's incorrectPaul Fertser1-1/+0
The end users on IRC report that actual USB device has different information in its descriptor so it doesn't match. Remove it altogether. Change-Id: Id7841667390a514581e630e67b9283675803135b Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1548 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-08-09remove the untested warning in ftdi/olimex-arm-usb-tiny-h.cfgSergey Alirzaev1-6/+0
the dongle seems working, including srst signal Change-Id: I5da9046bd8a35d8d826f1b663c01bd2600a6cf14 Signed-off-by: Sergey Alirzaev <zl29ah@gmail.com> Reviewed-on: http://openocd.zylin.com/1545 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-07-15ftdi/board: Add support for DENX M53EVKMarek Vasut1-0/+14
Add support for DENX M53EVK board and it's integrated on-board JTAG adapter using FT2232H. Change-Id: I022dcafa7799bb84a7873ba67ed82f1e49094320 Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Reviewed-on: http://openocd.zylin.com/1461 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2013-07-09ftdi/xds100v2.cfg: Remove the warning as it has been testedLaszlo Papp1-5/+0
Change-Id: I3a8711867e247bc49caa79274ae882f07719d4ce Signed-off-by: Laszlo Papp <lpapp@kde.org> Reviewed-on: http://openocd.zylin.com/1492 Reviewed-by: Peter Stuge <peter@stuge.se> Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2013-07-08cfg: Update Flyswatter 2 URLAndreas Fritiofson1-1/+1
It pointed to the Flyswatter 1 page. Change-Id: Ib7e82669a31cad2bf8f6ba4a60b25ef9920b2584 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/1478 Tested-by: jenkins Reviewed-by: Xiaofan <xiaofanc@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-06-12ftdi: config for TUMPAPaul Fertser1-0/+15
Add a config file for TIAO USB Multi-Protocol Adapter. Based on schematics from http://www.mediafire.com/?zv158nnx1gv0cy2 Cc: Volkan K <volkan-k@users.sourceforge.net> Change-Id: I0dfd93b0b1e558e4ccd7c94c005c099947ec94df Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1438 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2013-06-10Add BCM2835 (as found in Raspberry Pi) interface driverPaul Fertser1-0/+33
This adds support for JTAG programming by bitbanging GPIOs exposed on the RaspberryPi's expansion header. Tested by connecting directly to an STM32VLDiscovery board, without any additional circuity. I observed maximum about 4MHz on the TCK pin with an old analogue 'scope and about 100kHz when setting the speed to 100kHz. Busyloop waiting is needed because even with a single 0ns nanosleep call (with FIFO priority) it lowers the TCK speed to ~30kHz which is way too low to be useful. The speed testing with adapter_khz 2000 gave the following results: sudo chrt -f 1 nice -n -19 ./src/openocd \ -f interface/raspberrypi-native.cfg \ -c "set WORKAREASIZE 0x2000" \ -f target/stm32f1x.cfg -c "adapter_khz 2000" wrote 131072 bytes from file random.bin in 3.973677s (32.212 KiB/s) dumped 131072 bytes in 1.445699s (88.538 KiB/s) This is 3.7 times faster for writing and 14.3 times faster for reading compared to the generic sysfsgpio driver; probably the writing speed is limited by the target itself here and reading speed might be considerably higher too with appropriate connection and a capable target. BCM2835 name is choosen over BCM2708 because the published peripherals datasheet uses the particular model name and not family name. Change-Id: Ib78168be27f53c2a3c88c3dd8154d1190c318c78 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/758 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-06-05Added OpenJTAG DriverRyan Corbin1-0/+8
Updated OpenJTAG driver from www.openjtag.org to work with latest version of OpenOCD. Change-Id: I2917f4e5835fb9ca5265e81dc38515fa97ae9503 Signed-off-by: Ryan Corbin <corbin.ryan@gmail.com> Reviewed-on: http://openocd.zylin.com/1406 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-06-05aice: add Andes AICE supportHsiangkai Wang1-0/+15
Andes AICE uses USB to transfer packets between OpenOCD and AICE. It uses high-level USB commands to control targets instead of using JTAG signals. I define an interface as aice_port_api_s. It contains all basic operations needed by target-dependent code. Change-Id: I117bc4f938fab2732e44c509ea68b30172d6fdb9 Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com> Reviewed-on: http://openocd.zylin.com/1256 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-05-29interface/ftdi: remove "untested" warning from DP BusblasterPaul Fertser1-6/+0
This is reported as working by mitsakos on IRC. Change-Id: I26b97779c3e8e237c5b3996aa81183031b12ec0c Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/1419 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-03-13interface: opendous_ftdi config file addedRodrigo Melo1-0/+15
This config file add support to the opendous cable based on the chip ft2232H, using the ft2232 interface driver. Change-Id: I8171a0c475af8d61e081844ee86466a392138fb0 Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar> Reviewed-on: http://openocd.zylin.com/1096 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-03-07interface: opendous_ftdi config file addedRodrigo Melo1-0/+17
This config file add support to the opendous cable based on the chip ft2232H, using the ftdi interface driver. Change-Id: I4491f99d7b14f7078a04583ef0c4acd8692c4349 Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar> Reviewed-on: http://openocd.zylin.com/1097 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-02-08jtag_interface: .speed can be NULL when not neededFranck Jullien7-17/+0
adapter_init (core.c) won't check speed configuration of the selected interface if it's not needed (.speed = NULL). When it's not needed, we can now omit adapter_khz in init scripts and we don't have to implement dummy handlers for speed_div and khz functions. It also removes calls to adapter_khz in interface configuration files when not used anymore. Change-Id: I6eb1894385503fede542a368f297cec6565eed44 Signed-off-by: Franck Jullien <franck.jullien@gmail.com> Reviewed-on: http://openocd.zylin.com/1131 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2012-12-23icdi: add TI icdi interfaceSpencer Oliver1-0/+15
This is the new proprietary interface replacing the older FTDI based adapters. It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad. Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/922 Tested-by: jenkins
2012-12-23stlink: rename stlink cmd namesSpencer Oliver2-8/+8
As part of the switch to using the hla for the stlink interface we rename the cmds to a more generic name. Update scripts to match new names. Also add handlers for deprecated names. Change-Id: I6f00743da746e3aa13ce06acfdc93c8049545e07 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/921 Tested-by: jenkins
2012-12-23stlink: use common layoutSpencer Oliver2-2/+2
Even though the stlinkv1 and stlinkv2 use different usb classes they share the same layout scheme. Merge the two into a common layout, thus enabling us to support other adapter layouts. Change-Id: I7d02c44a7f94ebc7f2cb5428b02ee40294fb430d Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/918 Tested-by: jenkins
2012-10-28ftdi/flyswatter2.cfg: Define the LED signalPeter Stuge1-0/+1
Change-Id: Ic5d85c0d855bcffba54de7df6cff4d726656af97 Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://openocd.zylin.com/940 Tested-by: jenkins
2012-10-28ftdi/flyswatter2.cfg: Fix the signal layoutPeter Stuge1-8/+3
Change-Id: If6612af25fa3562f49e9c8ccff01b6ef0af5ceb0 Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://openocd.zylin.com/938 Tested-by: jenkins
2012-10-02lpc1768-stick: avoid driving srst high at startupSpencer Oliver1-1/+1
this avoid driving nSRST high after startup, by making sure the nOE is initialized inactive/high. This also matches the config used for the STM32-PerformanceStick. Change-Id: I9376de575b7dc834310d57dbd58575d51f60183e Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/878 Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com> Tested-by: jenkins
2012-10-02cfg: cortino tested and workingSpencer Oliver1-5/+0
Change-Id: I13534742c76ebbb05b47bf98768c997068da747a Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/851 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02cfg: fix incorrect cortino reset configSpencer Oliver1-2/+2
The cortino uses a direct srst connection rather than via any buffer. As a result this fixes issues with the newer ftdi driver. Change-Id: I28f6781bccae24de79aa6a03161f298a14fe2581 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/850 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02cfg: ftdi icdi enable srst open drain configSpencer Oliver1-1/+1
Change-Id: I21a115121f167dc88cd9bf2d1ca1ac9f3e1110d7 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/848 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02cfg: lm3s811ek config tested and workingSpencer Oliver1-5/+0
Change-Id: I5402b5521d6e1ef0a569f5cad02c003681f5444b Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/847 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02cfg: fix incorrect stm32-performance stick configSpencer Oliver1-2/+2
This hardware uses a output enable buffer that was not correctly defined. Fixes issues when using the new ftdi driver. Change-Id: Iba6235a71a6d3c7d16ab729f858b336a4574dfea Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/844 Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com> Tested-by: jenkins
2012-10-02cfg: stm32-performance stick config tested and workingSpencer Oliver1-5/+0
Change-Id: I9852d11e369e501af240a2b8e9f74306aee4e4a0 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/845 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02cfg: str9-comstick tested and workingSpencer Oliver1-5/+0
Change-Id: Ia6c45477381e78cb9508b4731438161e18be1f38 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/843 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02cfg: fix incorrect str9-comstick reset configSpencer Oliver1-2/+2
The str9-comstick uses a direct srst connection rather than via any buffer. As a result this fixes issues with the newer ftdi driver. Change-Id: I0968e8459997a6a2b7bf0c46e89662cd57b4f496 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/842 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-09-26drivers: new jtag bitbang driver using sysfs gpioMarc Reilly1-0/+24
This driver implements a bitbang jtag interface using gpio lines exported via sysfs. The aim of this driver implementation is to use system GPIOs but to avoid the need for an additional kernel driver. A config suitable for RaspberryPi is included. Change-Id: Ib2acf720247a219768d1cbfeebd88057ed2d7b8b Signed-off-by: Marc Reilly <marc@cpdesign.com.au> Reviewed-on: http://openocd.zylin.com/762 Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-08-29Add JTAG-lock-pick Tiny 2 config filesFreddie Chopin2-0/+24
DISTORTEC's JTAG-lock-pick Tiny 2 is a new interface using FT232HL chip and layout similar to KT-LINK. Change-Id: I2831b169cd448ca70397f2dd86c5b749dda3dabf Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com> Reviewed-on: http://openocd.zylin.com/787 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-08-24ftdi: Olimex ARM-USB-TINY validatedAurelien Jacobs1-6/+0
Flashing a CFI flash and debugging with gdb work fine. Change-Id: Ib2578ee6f41c1003968198439033d00d805122f7 Signed-off-by: Aurelien Jacobs <aurel@gnuage.org> Reviewed-on: http://openocd.zylin.com/770 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-08-14cfg: remove duplicate Olimex ARM-USB-OCD configSpencer Oliver1-11/+0
This file is already included as olimex-arm-usb-ocd.cfg. Change-Id: I0e66977c58e74ac93a0dc3a0c88a5e5af4992f8b Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-on: http://openocd.zylin.com/780 Tested-by: jenkins Reviewed-by: Peter Stuge <peter@stuge.se>
2012-08-09cfg: added new openocd-usb highspeed adapterAndrew Karpow2-0/+24
The embedded projects shop released a new highspeed version of the openocd-usb adapter. These configuration files adds support for it. Change-Id: I9b23d7889f998712b9041af101e3f0b9aba85b28 Signed-off-by: Andrew Karpow <notandyk@gmail.com> Reviewed-on: http://openocd.zylin.com/771 Tested-by: jenkins Reviewed-by: Peter Stuge <peter@stuge.se>
generated by cgit v1.1 at 2024-09-11 22:15:28 +0000