aboutsummaryrefslogtreecommitdiff
path: root/contrib
AgeCommit message (Collapse)AuthorFilesLines
2023-08-26contrib/firmware: add new i2c bit-banging feature to angie's firmwareAhmed BOUDJELIDA11-129/+485
add new i2c bit-banging feature, we can now connect in JTAG with the SoC target and in i2c with the main board components at the same time. Change-Id: I8e4516fe1ad5238e0373444f1c3c9bc0814d0f52 Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7796 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-26jtag/drivers: add new VIDs for angie driver - add a check for a returned valueAhmed BOUDJELIDA1-0/+2
add a line that checks the returned value of set signals function add two VIDs of other original boards (have onboard angie architecture) so angie driver can connect to them and change their VID after renumeration. Change-Id: Ide4f1f6f38168a410191bf3ff75bcd59dcf7ef50 Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7795 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-12jtag/drivers: Add new driver for ANGIE USB-JTAG AdapterAhmed BOUDJELIDA1-0/+4
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter. The driver is based on the openULINK project. This driver communicate with ANGIE's firmware in order to establish JTAG protocol to debug the target chip. Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the FX2 microcontroller, the driver adds two functions, one to download the firmware (embedded C) to the FX2, and the second to program the FPGA with its bitstream. Add ANGIE's configuration file to tcl/interface/ Add the device VID/PID to 60-openocd.rules file. Add ANGIE to OpenOCD's documentation Change-Id: Id17111c74073da01450d43d466e11b0cc086691f Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7702 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-08-12contrib/firmware: add new adapter ANGIE's firmware/bitstream codeAhmed BOUDJELIDA24-0/+3779
This is ANGIE's firmware and bitstream code. The 'Embeded C' code is based on the openULINK project. The hdl bitstream source code is for the spartan-6 FPGA included in ANGIE. Since ANGIE has a different microcontroller (EZ-USB FX2) than openULINK (EZ-USB AN2131), the registers file (reg_ezusb.h) has been changed completely, so are the descriptors, interruptions and the endpoints configuration. Change-Id: I70590c7c58bac6f1939c5ffba57e87d86850664d Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7701 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-08jtag/stlink: add STLINK-V3PWR supportLaurent LEMELE1-0/+2
STLINK-V3PWR is both a standalone debugger probe compatible with STLINK-V3 and a source measurement unit (SMU). Link: http://www.st.com/stlink-v3pwr This code adds support for the debugger probe functionality. Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1 Signed-off-by: Laurent LEMELE <laurent.lemele@st.com> Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7755 Tested-by: jenkins
2023-04-14flash/rsl10: fix typoMark Zhuang1-1/+1
Change-Id: I11af37309fe4684fcb340a00fcc7b2096b8dad76 Signed-off-by: Mark Zhuang <mark.zhuang@spacemit.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7584 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-04-01github/workflow: build libjaylink from sourceErhan Kurubas1-0/+13
Libjaylink submodule disabled by default at https://review.openocd.org/c/openocd/+/7129 --enable-internal-libjaylink config option will be deprecated soon. So, building the source is a permanent solution. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: Id06654d806a3a49f35e3ba41e9e4cc58c1a0d388 Reviewed-on: https://review.openocd.org/c/openocd/+/7552 Tested-by: jenkins Reviewed-by: zapb <dev@zapb.de> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-01-15flash/nor, contrib/loaders: move numicro M0 write assembly to contrib/loadersJian-Hong Pan5-2/+80
Simply move numicro M0 flash write assembly to contrib/loaders. Also, modify corresponding Makefile and generated numicro_m0.inc. To make the path more general, this patch rename the path "contrib/loaders/flash/numicro_m4" to "contrib/loaders/flash/numicro" as well. Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com> Change-Id: I9adea24c2b3c97319a9b015cf50257f3d131dc26 Reviewed-on: https://review.openocd.org/c/openocd/+/7346 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-01-15flash/nor, contrib/loaders: move numicro M4 write assembly to contrib/loadersJian-Hong Pan3-0/+106
Simply move numicro M4 flash write assembly to contrib/loaders. Also, add corresponding Makefile and generated numicro_m4.inc. Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com> Change-Id: I22b8be0a245857335b11bd0b538db415fc34748d Reviewed-on: https://review.openocd.org/c/openocd/+/7343 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-01-15nds32: drop it, together with aice adapter driverAntonio Borneo1-1/+0
The target nds32 and its companion adapter aice have not received any real improvement since 2013. It has been hard to keep them aligned during the evolution of OpenOCD code, with no way for maintainers to really check if they are still working. No real documentation is present for them in OpenOCD. The nds32 code triggers ~50 errors/warnings with scan-build. The arch nds32 has been dropped from Linux kernel v5.18-rc1. For all the reasons above, this code has been deprecated with commit 2e5df83de7f2 ("nds32: deprecate it, together with aice adapter driver") and tagged to be dropped before v0.13.0. Let it r.i.p. in OpenOCD git history. While there, drop from checkpatch list the camelcase symbols that where only used in this code. Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7382 Tested-by: jenkins
2022-09-18openocd: fix SPDX tag format for files .cAntonio Borneo26-26/+26
With the old checkpatch we cannot use the correct format for the SPDX tags in the file .c, in fact the C99 comments are not allowed and we had to use the block comment. With the new checkpatch, let's switch to the correct SPDX format. Change created automatically through the command: sed -i \ 's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \ $(find src/ contrib/ -name \*.c) Change-Id: I6da16506baa7af718947562505dd49606d124171 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7153 Tested-by: jenkins
2022-09-13src/flash/nor: flash driver for RSL10Toms Stūrmanis3-0/+60
Add new flash driver for internal flash of onsemi RSL10 device. Valgrind-clean. Clang AddressSanitizer shows no errors. Signed-off-by: Toms Stūrmanis <toms.sturmanis@gmail.com> Change-Id: I8030542cb9805e94f56d7a69404cef5d88d6dd5a Reviewed-on: https://review.openocd.org/c/openocd/+/7115 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2022-09-13contrib: add GPL license tag on files that miss itAntonio Borneo35-0/+69
Some file miss completely the license tag. Add the SPDX tag, using the same GPL-2.0-or-later license of the OpenOCD project. The SPDX tag on files *.c is incorrect, as it should use the C99 single line comment using '//'. But current checkpatch doesn't allow C99 comments, so keep using standard C comments, by now. Change-Id: I24bd362eeb6b74f09aceb9b757d45cbfa4afe334 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7160 Tested-by: jenkins
2022-09-13contrib: replace the GPLv2-or-later license tagAntonio Borneo65-901/+131
Replace the GPLv2-or-later boilerplate with the SPDX tag. The SPDX tag on files *.c is incorrect, as it should use the C99 single line comment using '//'. But current checkpatch doesn't allow C99 comments, so keep using standard C comments, by now. Change-Id: I380d552940f1c405309a3346454251c0e80b5a45 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7159 Tested-by: jenkins
2022-09-13contrib: replace the BSD-3-Clause license tagAntonio Borneo29-752/+62
Replace the BSD-3-Clause boilerplate with the SPDX tag. Add the SPDX tag and the copyright to two makefiles that were added by TI with the other files in their respective folder. The SPDX tag on files *.c is incorrect, as it should use the C99 single line comment using '//'. But current checkpatch doesn't allow C99 comments, so keep using standard C comments, by now. Change-Id: I3ad1b2dbdb6054b74dcc26e394c9223ba0427caf Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7158 Tested-by: jenkins
2022-09-13contrib: replace the GPLv3-or-later license tagAntonio Borneo3-17/+8
These files are not built in OpenOCD and are not in conflict with OpenOCD license. Replace the GPL boilerplate with the SPDX tag. Add the SPDX tag. The SPDX tag on files *.c is incorrect, as it should use the C99 single line comment using '//'. But current checkpatch doesn't allow C99 comments, so keep using standard C comments, by now. Change-Id: I934e4add24098f0e8574120b3bc32e9bcf166abd Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7157 Tested-by: jenkins
2022-09-13openocd: fix syntax of SPDX tagsAntonio Borneo7-14/+13
Put the SPDX tag alone in a comment in the first line of the file. Replace the obsolete GPL-2.0+ tag The SPDX tag on files *.c is incorrect, as it should use the C99 single line comment using '//'. But current checkpatch doesn't allow C99 comments, so keep using standard C comments, by now. Change-Id: Ia91b0f7da42c439b6340bbe81983b86b68f6d65c Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7156 Tested-by: jenkins
2022-08-27doc: how to use QEMU to test big-endian buildAntonio Borneo1-0/+27
Document the process of using buildroot to build a big-endian binary of OpenOCD and using QEMU User Mode Emulation for running the big-endian binary on a little-endian host PC. Change-Id: Ic5fe26e353a4cf69e57af3c23ae7fa4b25347b2b Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/6968 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2022-08-15loaders/reset/espressif: replace the GPL-2.0-or-later license tagErhan Kurubas5-65/+10
Replace the FSF boilerplate with the SPDX tag. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: Iddccae2bd8906a3587a2aa2684124356a340fc74 Reviewed-on: https://review.openocd.org/c/openocd/+/7105 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2022-07-02jtag: add esp_usb_jtag driverErhan Kurubas1-0/+4
This driver is used with the ESP32 chips which has builtin USB-JTAG interface. e.g. with ESP32-C3, ESP32-S3 Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: If966268cb8d26f76540dd5440245a17ed0b72c61 Reviewed-on: https://review.openocd.org/c/openocd/+/6943 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2022-06-24target: add Espressif ESP32-S3 basic supportErhan Kurubas3-0/+200
ESP32-S3 is a dual core Xtensa SoC Not full featured yet. Some of the missing functionality: -Semihosting -Flash breakpoints -Flash loader -Apptrace -FreeRTOS Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794 Reviewed-on: https://review.openocd.org/c/openocd/+/6990 Tested-by: jenkins Reviewed-by: Ian Thompson <ianst@cadence.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2022-06-24target: add Espressif ESP32 basic supportErhan Kurubas4-0/+242
ESP32 is a dual core Xtensa SoC Not full featured yet. Some of the missing functionality: -Semihosting -Flash breakpoints -Flash loader -Apptrace -FreeRTOS Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750 Reviewed-on: https://review.openocd.org/c/openocd/+/6989 Tested-by: jenkins Reviewed-by: Ian Thompson <ianst@cadence.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2022-06-03github/workflow: enable libftdi based adaptersTarek BOCHKATI1-4/+10
Change-Id: I74b07b21573294dd7d9d3caf41c5755622c77149 Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7008 Tested-by: jenkins Reviewed-by: Xiaofan Chen <xiaofanc@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2022-05-07cross-build.sh: fix build with capstoneTarek BOCHKATI1-1/+1
since commit 12d1ad0c7529 : update capstone include path ... the generated capstone.pc is not working so fix the includedir in capstone.pc to get github action working Change-Id: I7767e181a74c73a7514eeb6293cd556a794dbfe9 Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/6969 Tested-by: jenkins Reviewed-by: Tim Newsome <tim@sifive.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2022-04-24flash/stm32f1x: add support for RISC-V GigaDevice GD32VF103Tomas Vanek3-0/+65
The device has compatible flash macro with STM32F1 family, reuse stm32f1x driver code. Detect non-ARM target - for simplicy test target type name 'riscv' and the address has 32 bits. In case of RISC-V CPU use simple chunked write algo - async algo cannot be used as the core implemented in this device doesn't allow memory access while running. Change-Id: Ie3886fbd8573652691f91a02335812a7300689f7 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: https://review.openocd.org/c/openocd/+/6704 Tested-by: jenkins Reviewed-by: Tim Newsome <tim@sifive.com>
2022-03-12Remove all occurrences of 'mem2array' and 'array2mem'Marc Schink1-13/+5
Replace deprecated commands 'mem2array' and 'array2mem' with new Tcl commands 'read_memory' and 'write_memory'. Change-Id: I116d995995396133ca782b14cce02bd1ab917a4e Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: https://review.openocd.org/c/openocd/+/6859 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-12-24contrib/udev: Add missing J-Link USB PIDMarc Schink1-0/+2
See libjaylink/contrib/99-libjaylink.rules Change-Id: I36733e18eb4bc11828c5fa563c687d28be9e34bd Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: https://review.openocd.org/c/openocd/+/6778 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-12-03flash/nor/fespi: algorithm, large address, errorsTim Newsome8-125/+498
* Move more smarts into the target algorithm code, and rewrite that in C so it's easier to understand/maintain. * Support >24-bit addresses. * Check for errors. Change-Id: I3b1a143589fe6defafb8f95820aa682acc9646e7 Signed-off-by: Tim Newsome <tim@sifive.com> Reviewed-on: https://review.openocd.org/c/openocd/+/6679 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2021-11-03flash/nor/stm32lx: fixed writes at high adapter speedsJimmy2-19/+37
The busy flag must be polled after each half-page write. At low clock speeds, no issue is observed when the poll is omitted, because the writes complete before the next write begins. But at high clock speeds the subsequent writes would overlap and cause the operation to fail. The status polls are done on the target for efficiency, since the half-pages are very small. Change-Id: Ia1e9b4a6a71930549b3d84a902744ce6e596301b Signed-off-by: Jimmy <nhminus@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/5598 Tested-by: jenkins Reviewed-by: Jelle De Vleeschouwer Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
2021-10-02udev: add ASIX Presto programmerAntonio Borneo1-0/+3
The driver is in OpenOCD since 2007, but the USB VID/PID have never been listed in udev rules. Change-Id: I77df469929dd7f6b6483678c0e76f22c30a7614c Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/6563 Tested-by: jenkins
2021-09-18stlink: Add PID for V3 device without MSDAndreas Sandberg1-0/+1
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been disabled. This PID has been observed on a Nucleo-G431RB board. Signed-off-by: Andreas Sandberg <andreas@sandberg.uk> Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976 Reviewed-on: https://review.openocd.org/c/openocd/+/6555 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-09-12flash/stm32l4x: fix flash programming in 64-bit hostsTarek BOCHKATI1-0/+2
stm32l4_work_area struct is shared between the loader and stm32l4x flash driver '*wp' and '*rp' pointers' size is 4 bytes each since stm32l4x devices have 32-bit processors. however when used in openocd code, their size depends on the host if the host is 32-bit, then the size is 4 bytes each. if the host is 64-bit, then the size is 8 bytes each. to avoid this size difference, change their types depending on the usage (pointers for the loader, and 32-bit integers in openocd code). Change-Id: I0a3df4bb4bf872b01cdb9357eb28307868d7d469 Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/6556 Tested-by: jenkins Reviewed-by: Yestin Sun <sunyi0804@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2021-09-02flash/stm32l4x: switch to to c loader instead of assembly loaderTarek BOCHKATI4-113/+205
switching to C loader instead of the assembly version will enhance readability will reduce the maintenance effort. besides the switch to C loader, we added a new parameters to the loader like flash_word_size and flash_sr_bsy_mask in order to support properly STM32U5x and STM32G0Bx/G0Cx in dual-bank mode. Change-Id: I24cafc2ba637a065593a0506eae787b21080a0ba Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/6109 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2021-09-02flash/nor: add support for Nuvoton NPCX series flashWealian Liao6-0/+735
Added NPCX flash driver to support the Nuvoton NPCX series microcontrollers. Add config file for NPCX series. Change-Id: Ia10b019a3521f59ad1e10ccdc56827ba30c3eac8 Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com> Signed-off-by: Mulin Chao <mlchao@nuvoton.com> Reviewed-on: https://review.openocd.org/c/openocd/+/5950 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2021-08-25tcl: add lattice ECP5 family supportOleksij Rempel1-0/+2
Add support for ECP5 FPGA targets and board based on this chips: Radiona ULX3S and Lambdaconcept ECPIX-5 Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-on: https://review.openocd.org/c/openocd/+/6112 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2021-08-14tcl/interface: add Ashling Opella-LD FTDI config filesRanjith Chandran1-0/+3
Adding Ashling's FTDI based Debug adapter Opella-LD's JTAG and SWD config files Change-Id: Ie0e82e3b8326de37641901f5c825372cab31de58 Signed-off-by: ranjith.tc@ashling.com Reviewed-on: http://openocd.zylin.com/6379 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-08-14drivers/remote_bitbang: Group adapter commandsMarc Schink1-2/+2
Use a command group 'remote_bitbang' with subcommands instead of individual commands with 'remote_bitbang_' prefix. The old commands are still available for backward compatibility but marked as deprecated. Change-Id: I2692320f19c8a357112a365db6ca7e13cd6ad411 Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: http://openocd.zylin.com/6389 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-06-18contrib/itmdump.c: fix implicit declaration warningDiego Herranz1-1/+2
atoi used but stdlib.h wasn't included. Also, include statements reordered alphabetically. Change-Id: I7fcdbf3fa940a172204ec811399e1a7fdebdc979 Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com> Reviewed-on: http://openocd.zylin.com/6312 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-06-04contrib: add an example of using list.hAndreas Fritiofson1-0/+74
Change-Id: Ic3d399d7ad2e4d10677cf78d64968040941b74e5 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/6280 Tested-by: jenkins Reviewed-by: Tim Newsome <tim@sifive.com>
2021-05-01udev rules: add OSBDM deviceJiri Kastner1-0/+5
Change-Id: I7221a6b3fe6fcd4f17ea664c10fd32c645e21d7c Signed-off-by: Jiri Kastner <cz172638@gmail.com> Reviewed-on: http://openocd.zylin.com/6198 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-04-05udev rules: add missing Altera USB Blaster devicesAntonio Borneo1-0/+6
All Altera USB Blaster devices require a dedicated line in the udev rules, but some USB VID/PID present in interface and board config file is missing in udev rules. Add the missing Altera USB Blaster devices in udev rules. While there, fix an incorrect pair VID/PID that are reported swapped inside a comment. Change-Id: I2d67e90b10db99ef2638405585859c1393456f65 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/6102 Tested-by: jenkins
2021-04-05udev rules: add missing ftdi USB VID/PIDAntonio Borneo1-0/+23
All ftdi devices require a dedicated line in the udev rules, but some USB VID/PID present in interface and board config file is missing in udev rules. Add the missing ftdi devices in udev rules. Change-Id: I850a4a95a2d4bb63b3fd09be803be8c23c4d6b49 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/6101 Tested-by: jenkins
2021-03-20tcl/interface/ftdi: Add PLS SPC5 debugger configAndrew Wesie1-0/+3
Change-Id: I694201db0811beebc94e87822c87fbfc6aecc4c4 Signed-off-by: Andrew Wesie <awesie@gmail.com> Reviewed-on: http://openocd.zylin.com/6081 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-03-19tcl/interface/ftdi: Add miniWiggler debugger configAndrew Wesie1-0/+3
Change-Id: I91f73a377cd9525008d09fda7a7c58d498014b74 Signed-off-by: Andrew Wesie <awesie@gmail.com> Reviewed-on: http://openocd.zylin.com/6111 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2021-03-19Implement CRC32 algorithm for RISC-V.Tim Newsome4-4/+301
Signed-off-by: Tim Newsome <tim@sifive.com> Change-Id: Id437f78e74e3d837ff203f84c4eeb996bfad9a01 Reviewed-on: http://openocd.zylin.com/6076 Reviewed-by: Jan Matyas <matyas@codasip.com> Reviewed-by: Marc Schink <dev@zapb.de> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2021-01-13udev: fix permission for Ambiq Micro EVK'sAntonio Borneo1-3/+3
Commit 68e204f1e91a ("udev: Add rules for Ambiq Micro EVK's.") was initially proposed as http://openocd.zylin.com/3429/ then replaced by http://openocd.zylin.com/3980/ The initial proposal was for file '99-openocd.rules', in which MODE="664" was the norm. After merge of http://openocd.zylin.com/2804/ the new udev rules in '60-openocd.rules' switched to MODE="660", but the evolution of the above patch missed this change. Switch udev rules of Ambiq Micro EVK's to MODE="660" and uniform them to the rest of the file. Change-Id: I4b4eea535184ee8569da3264bff4f1fafb5bce4d Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Fixes: 68e204f1e91a ("udev: Add rules for Ambiq Micro EVK's.") Reviewed-on: http://openocd.zylin.com/6004 Tested-by: jenkins
2021-01-13contrib: udev file for Cypress SuperSpeed Explorer kitJiri Kastner1-0/+3
lsusb output: Bus 003 Device 011: ID 04b4:0007 Cypress Semiconductor Corp. Couldn't open device, some information will be missing Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x04b4 Cypress Semiconductor Corp. idProduct 0x0007 bcdDevice 0.00 iManufacturer 1 iProduct 2 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 114 bNumInterfaces 4 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 100mA Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 0 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Union: bMasterInterface 0 bSlaveInterface 1 CDC Call Management: bmCapabilities 0x00 bDataInterface 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 4 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 5 bInterfaceProtocol 0 iInterface 0 Change-Id: I62f0300199da3551c8774a4a5a4cd106a3ab2904 Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Jiri Kastner <cz172638@gmail.com> Reviewed-on: http://openocd.zylin.com/3611 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-01-08contrib: rpc_examples: haskell: fix ftbs with current librariesPaul Fertser1-7/+4
And get rid of some warnings along the way. Change-Id: I8fdbe1fa304276be6b0f25249b902b3576aa3793 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/5987 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-11-1560-openocd.rules: add ULINKplus CMSIS-DAP based adapterTarek BOCHKATI1-0/+1
Change-Id: I5935e0a184b8995122d197046ef8fb4e7eefb884 Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com> Reviewed-on: http://openocd.zylin.com/5926 Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2020-11-08Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interfaceAndreas Bolsch18-0/+1910
- write speed up to 150 kByte/s on STM32F469I-disco (due to SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in dual 4-line mode or STM32H73BI-Disco in octal mode - tested with STM32L476G-disco (64MBit flash, 3-byte addr), STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and STM32L476G-Disco (all 128Mbit flash, 3-byte addr), STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr) STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr) STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr) STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr) - suitable cfg for Discovery boards included - limited parsing of SFDP data if flash device not hardcoded (tested only in single/quad mode as most devices either don't support SFDP at all or have empty(!) SFDP memory) - 'set' command for auto detection override (e. g. for EEPROMs) - 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.) - makefile for creation of binary loader files - tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg - tcl/board/stm32f7discovery.cfg removed as name is ambiguous (superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg) - dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI with two W25Q128FV, sample cfg files included and on STM32H745I-Disco, STM32H747I-Disco, STM32H750B-Disco - read/verify/erase_check uses indirect read mode to work around silicon bug in H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last bytes causes debug interface to hang) - octospi supported only in single/dual 1-line, 2-line, 4-line and single 8-line modes, (not in hyper flash mode) Requirements: GPIOs must be initialized appropriately, and SPI flash chip be configured appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip specific, cf. included cfg files. The driver infers most parameters from current setting in CR, CCR, ... registers. Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8 Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com> Reviewed-on: http://openocd.zylin.com/4321 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Christopher Head <chead@zaber.com>
generated by cgit v1.1 at 2024-10-12 17:28:13 +0000