aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2023-08-26jtag/drivers: add new VIDs for angie driver - add a check for a returned valueAhmed BOUDJELIDA2-4/+10
add a line that checks the returned value of set signals function add two VIDs of other original boards (have onboard angie architecture) so angie driver can connect to them and change their VID after renumeration. Change-Id: Ide4f1f6f38168a410191bf3ff75bcd59dcf7ef50 Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7795 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-26mips32: add per-cpu quirks featureArtur Rojek6-1/+104
Introduce the ability to detect CPUs based on CP0 PRId register and apply cpu specific quirks, which alter the default ejtag behavior. First of those is EJTAG_QUIRK_PAD_DRET, which makes sure extra NOPs are placed after the DRET instruction on exit from debug mode. This fixes resume behavior on Ingenic JZ4780 SoC. The proper detection of some (currently unsupported) CPUs becomes quite complicated, so please consult the following Linux kernel code when adding new CPUs: * arch/mips/include/asm/cpu.h * arch/mips/kernel/cpu-probe.c Change-Id: I0f413d5096cd43ef346b02cea85024985b7face6 Signed-off-by: Artur Rojek <contact@artur-rojek.eu> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: https://review.openocd.org/c/openocd/+/7859 Tested-by: jenkins
2023-08-26stlink: increase stlink v2 max speed to 2.25 MbpsMarcin Niestroj1-1/+1
stlink v2 on Nucleo-64 board (e.g. NUCLEO-L476RG) has target SWO signal connected to STM32F103CB'S PA10, which is UART1_RX. UART1 within this MCU in theory can be configured to 4.5 Mbps baudrate, which means this is the upper limit supported by HW. As a confirmation BMP (Black Magic Probe) project also states in documentation that UART1 can be used with up to 4.5 Mbps baudrate. Tests have shown that configuring 4.5 Mbps baudrate on stlink v2 available on NUCLEO-L476RG board results in receiving corrupted data. Using 2.25 Mbps however allows to successfully receive all data from SWO. This makes sense in terms of STM32F103CB capabilities, since 2.25 Mbps is the next supported baudrate due to division by 2. Increase supported stlink v2 SWO speed from 2 to 2.25 Mbps. Tested with NUCLEO-L476RG: $ stm32l4x.tpiu configure -protocol uart \ -traceclk 80000000 -pin-freq 2250000 \ -output /dev/stdout $ stm32l4x.tpiu enable 2.25 Mbps speed confirmed with logic analyzer. Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev> Change-Id: Icbec04585664aba8b217e8f9a75458e577f7617f Reviewed-on: https://review.openocd.org/c/openocd/+/7848 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-26tcl/board: Add j721e native swd configurationKaelin Laundry2-0/+31
Direct memory driver swd native configuration for j721E Signed-off-by: Kaelin Laundry <wasabifan@outlook.com> Signed-off-by: Nishanth Menon <nm@ti.com> Change-Id: I27455040f48c47271ae110afd114fce005824969 Reviewed-on: https://review.openocd.org/c/openocd/+/7259 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-26tcl/board: Add am625 native swd configurationNishanth Menon2-0/+51
Direct memory driver swd native configuration for am625. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Jason Peck <jpeck@ti.com> Change-Id: I6cf521fe9af0a4b8f8ab4853bc25722368b713e6 Reviewed-on: https://review.openocd.org/c/openocd/+/7091 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-08-26jtag/drivers: dmem: Add Emulated AP modeJason Peck2-6/+299
This emulation mode supports software translation of an AP request into an address mapped transaction that does not rely on physical AP hardware. This is necessary in some hardware such as K3 SoCs since the hardware architecture anticipates a potential race condition between AP doing direct memory access generating transactions back to system bus and firewalls that data path out. This emulation mode allows direct memory driver to emulate CoreSight Access Port (AP) and reuse the SoC configuration meant for JTAG debuggers. Since the address ranges are flat in nature, the requisite memory base and size will need to be provided a-priori to the driver for mapping. The other design alternative would be to map requested memory map for every register operation, but, that would defeat our intent of getting max debug performance. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Jason Peck <jpeck@ti.com> Change-Id: I2d3c5f7833f1973e90b4f6b247827f62fc2905d0 Reviewed-on: https://review.openocd.org/c/openocd/+/7089 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-26jtag/drivers: Add dmem driverNishanth Menon6-0/+424
Direct memory driver support for CoreSight Access Port(AP). Even though we emulate SWD (serial wire debug), we aren't actually using swd. Instead, we are using a direct memory access to get to the register set. This is similar in approach to other fast access native drivers such as am335xgpio drivers. Example operation on Texas Instrument's AM62x K3 SoC: +-----------+ | OpenOCD | SoC mem map | on |--------------+ | Cortex-A53| | +-----------+ | | +-----------+ +-----v-----+ |Cortex-M4F |<───────| | +-----------+ | | | DebugSS | +-----------+ | | |Cortex-M4F |<───────| | +-----------+ +-----------+ Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Jason Peck <jpeck@ti.com> Change-Id: I8470cb15348863dd844b2c0e3f63a9063cb032c6 Reviewed-on: https://review.openocd.org/c/openocd/+/7088 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-26tcl/board: add TI am62a7evm configJason Kacines1-0/+25
Add basic connection details with am625 SK/EVM For further details, see https://www.ti.com/tool/SK-AM62A-LP Change-Id: I0b6b4004f3a04be7a90207e44c588a4f68aff47a Signed-off-by: Jason Kacines <j-kacines@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7855 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2023-08-26tcl/target/ti_k3: Add AM62A7 SoCJason Kacines1-0/+23
Add support for the TI K3 family AM62A7 SoC. For further details, see https://www.ti.com/lit/pdf/spruj16a Change-Id: Ie69bde4895f34b04f9967f63d1ca9c8149c50b8a Signed-off-by: Jason Kacines <j-kacines@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7854 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2023-08-26tcl/target/ti_k3: Add missing documentation for supported SoCsJason Kacines1-0/+4
Add links for the SoCs are supported by the conf file for future reference. Change-Id: Ic5b7786ef3ac31414fe2ce56c1237a18ce99aaa1 Signed-off-by: Jason Kacines <j-kacines@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7853 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2023-08-26rtos/zephyr: arm: fetch arm exc return offsetBruno Mendes1-0/+1
Since zephyrproject-rtos/zephyr@c3eeae8, Zephyr OS exposes offset of mode_exc_return in the arch struct for ARM. Accounting for this allows for consistency and enables logic with further offsets that may be added after this. Signed-off-by: Bruno Mendes <bd_mendes@outlook.com> Change-Id: Id53ebd80c5d98a7d94eb6b00ad638ce51e719822 Reviewed-on: https://review.openocd.org/c/openocd/+/7851 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-08-26tcl/target: add Realtek RTL872xD configKarl Palsson1-0/+33
Sufficient to probe both cores via multiple APs. No support listed for jtag in the datasheet or usermanual. Tested against a BW-16 board: https://www.amebaiot.com/en/amebad/#partner_bw16 Change-Id: Idf82085e7b7327fdf3d6d668e6fb59eff6e0431b Signed-off-by: Karl Palsson <karlp@tweak.au> Reviewed-on: https://review.openocd.org/c/openocd/+/7847 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-08-26target/cortex_m: Add Realtek Real-M200 and M300Karl Palsson3-0/+14
These cores are advertised as M23 and M33 compatible, but are identified by the Realtek implementor id. These cores are found on the RTL872xD family, at least. Raw CPUIDs: Real-M200 (KM0): 721cd200 Real-M300 (KM4): 721fd220 Change-Id: I4106ccb7e8c562f98072a71e9e818f57999d664e Signed-off-by: Karl Palsson <karlp@tweak.au> Reviewed-on: https://review.openocd.org/c/openocd/+/7846 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-26target/cortex_m: check core implementor fieldKarl Palsson7-38/+52
Presently, we only look at the Part Number field of the CPUID, and completely ignore the Implmentor field, simply assuming it to be ARM. Parts have since been found, with different implementors, that use overlapping part numbers, causing detection to fail. Expand the "part number" field to be a full implementor+part number, excluding the revision/patch fields, to make checking more reliable. Change-Id: Id81774f829104f57a0c105320d0d2e479fa01522 Signed-off-by: Karl Palsson <karlp@tweak.au> Reviewed-on: https://review.openocd.org/c/openocd/+/7845 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2023-08-26efm32: drop unnecessary and incomplete checksKarl Palsson1-12/+0
There's really no reason to try and add an extra layer of cpu verification here. Change-Id: If8c4aa03754607be6c089f514ae300b09b067ffa Signed-off-by: Karl Palsson <karlp@tweak.au> Reviewed-on: https://review.openocd.org/c/openocd/+/7844 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-12flash/nor/spi: Improve erase performance on zd25q16Nikolay Dimitrov1-1/+1
Use blocks (64 KiB) instead of sectors (4 KiB) when erasing the zd25Q16 SPI flash memory (thanks to Tomas Vanek!) Change-Id: I969a69ad35f51b84eb3e11b93f0d79db3e98613a Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org> Reviewed-on: https://review.openocd.org/c/openocd/+/7850 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2023-08-12flash/nor/spi: add zetta zd25q16Nikolay Dimitrov1-0/+1
* Zetta 16 Mbit (2 MiB) SPI flash * Tested on Olimex RP2040-PICO30 and Neo6502 boards Change-Id: I02224dd7a72a9b72f01b31edbd958daa23f28956 Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org> Reviewed-on: https://review.openocd.org/c/openocd/+/7849 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2023-08-12pld: allow calling of configuration functions before 'init'Daniel Anselmi2-3/+3
Change-Id: I7c475fbbf8c13ae227e3393f01528eb180e9de51 Signed-off-by: Daniel Anselmi <danselmi@gmx.ch> Reviewed-on: https://review.openocd.org/c/openocd/+/7835 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-12pld: fix sparser warningsDaniel Anselmi2-2/+2
Change-Id: I31c5b19cd93ac41b026f824337488c9aa9b12439 Signed-off-by: Daniel Anselmi <danselmi@gmx.ch> Reviewed-on: https://review.openocd.org/c/openocd/+/7828 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-12target/aarch64: add missing aarch64_poll() callsDaniel Goehring1-0/+9
Add missing aarch64_poll() calls to ensure the event TARGET_EVENT_HALTED is called when necessary. This is needed with the poller update introduced in commit 95603fae18f8 ("openocd: revert workarounds for 'expr' syntax change") Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com> Change-Id: I6e91f1b6bc1f0d16e6f0eb76fc67d20111e3afd2 Reviewed-on: https://review.openocd.org/c/openocd/+/7737 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-12tcl: add configuration files for the ARC HSDK-4xD boardArtemiy Volkov2-0/+69
This commit provides startup files for the Synopsys DesignWare ARC HSDK-4xD board. These have been adapted from the corresponding snps_hsdk.cfg files, the only functional change being the JTAG IDs for the new board's CPU cores. Change-Id: I19a0cd13bc09de90cfe2a7cccf1239e459fd8077 Signed-off-by: Artemiy Volkov <artemiy@synopsys.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7829 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Evgeniy Didin <didin@synopsys.com>
2023-08-12tcl/interface/ftdi: support for SIPEED RV-Debuggergudvinr1-0/+13
BL702-based JTAG debugger that emulates FT2232D device Change-Id: Iefbf03645e6d8d154f4b1cad3385b8bc09da37dd Signed-off-by: gudvinr <gudvinr@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7830 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-08-12jtag/drivers: Add new driver for ANGIE USB-JTAG AdapterAhmed BOUDJELIDA12-0/+2488
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter. The driver is based on the openULINK project. This driver communicate with ANGIE's firmware in order to establish JTAG protocol to debug the target chip. Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the FX2 microcontroller, the driver adds two functions, one to download the firmware (embedded C) to the FX2, and the second to program the FPGA with its bitstream. Add ANGIE's configuration file to tcl/interface/ Add the device VID/PID to 60-openocd.rules file. Add ANGIE to OpenOCD's documentation Change-Id: Id17111c74073da01450d43d466e11b0cc086691f Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7702 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-08-12contrib/firmware: add new adapter ANGIE's firmware/bitstream codeAhmed BOUDJELIDA25-0/+3847
This is ANGIE's firmware and bitstream code. The 'Embeded C' code is based on the openULINK project. The hdl bitstream source code is for the spartan-6 FPGA included in ANGIE. Since ANGIE has a different microcontroller (EZ-USB FX2) than openULINK (EZ-USB AN2131), the registers file (reg_ezusb.h) has been changed completely, so are the descriptors, interruptions and the endpoints configuration. Change-Id: I70590c7c58bac6f1939c5ffba57e87d86850664d Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7701 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-12libusb_helper: split error and returned valueAntonio Borneo8-62/+85
The USB control transfer can be executed without any data. The libusb API libusb_control_transfer() can thus be called with zero 'size', thus returning zero byte transferred when succeed. The OpenOCD API jtag_libusb_control_transfer() returns zero either in case of transfer error and in case of libusb_control_transfer() returning zero, making impossible discriminating the two cases. Extend jtag_libusb_control_transfer() with separate return value for error code and explicit parameter's pointer for transferred bytes. Make the transferred pointer optional, as many callers do not properly handle the returned value. Use 'int' type pointer for transferred, instead of the 'uint16_t' that would have matched the type of 'size'. This can simplify the caller's code by using a single 'int transferred' variable shared with other jtag_libusb_bulk_read|write, while keeping possible the comparison int vs uint16_t without cast. This change is inspired from commit d612baacaa3f ("jtag_libusb_bulk_read|write: return error code instead of size") Change-Id: I14d9bff3e845675be03465c307a136e69eebc317 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7756 Tested-by: jenkins Reviewed-by: ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
2023-08-12LICENSES: Add the LGPL-2.1 licenseThomas Gleixner2-0/+504
Add the full text of the LGPL 2.1 license to OpenOCD. It was copied directly from: https://spdx.org/licenses/LGPL-2.1.html#licenseText Add the required tags for reference and tooling. Checkpatch-ignore: FSF_MAILING_ADDRESS Change-Id: I081f2197fb3c60e17cd6e3353d38194c720ee8a3 Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7743 Tested-by: jenkins Reviewed-by: ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
2023-08-08breakpoints: use 64-bit type for watchpoint mask and valueParshintsev Anatoly10-34/+36
This patch changes data types of watchpoint value and mask to allow for 64-bit values match that some architectures (like RISCV) allow. In addition this patch fixes the behavior of watchpoint command to zero-out mask if only data value is provided. Change-Id: I3c7ec1630f03ea9534ec34c0ebe99e08ea56e7f0 Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7840 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com> Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2023-08-05doc: port "0" requests any available port for usage by OpenOCD serverParshintsev Anatoly1-0/+3
Change-Id: I0d38533748898516dce44e81d0bff6bd35ee4aec Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7842 Reviewed-by: Jan Matyas <jan.matyas@codasip.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2023-08-05pld/virtex2: allow calling set_instr_codes and set_user_codes before 'init'Daniel Anselmi1-2/+2
Change-Id: Ib21366b2fdbf33ee06a958e52b725989114751f4 Signed-off-by: Daniel Anselmi <danselmi@gmx.ch> Reviewed-on: https://review.openocd.org/c/openocd/+/7821 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-08-03register: refactor register_cache_invalidate()Marek Vrbka1-3/+2
register_cache_invalidate() is written a way which uses pointer arithmetic, which makes it harder to read. This patch replaces it with more readable way to iterate over array of structs. Change-Id: Ia420f70a3bb6998c690c8c600c71301dca9f9dbf Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7735 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
2023-07-29target: fix messages and return values of failed op because not haltedTomas Vanek29-131/+145
Lot of messages was logged as LOG_WARNING, but the operation failed immediately. Sometimes no error message was logged at all. Add missing messages, change warnings to errors. Sometimes ERROR_TARGET_INVALID was returned. Some command handlers returned ERROR_OK! Always return ERROR_TARGET_NOT_HALTED. While on it use LOG_TARGET_ERROR() whenever possible. Prefix command_print() message with 'Error:' to get closer to LOG_TARGET_ERROR() variant. Error message was not added to get() and set() methods of struct xxx_reg_type - the return value is properly checked and a message is logged by the caller in case of ERROR_TARGET_NOT_HALTED. Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Change-Id: I2fe4187c6025f0038956ab387edbf3f461c69398 Reviewed-on: https://review.openocd.org/c/openocd/+/7819 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-24jtag/drivers/xds110: Fix compiler warning.Tim Newsome1-10/+1
Compiler would complain that `written` was used without being initialized. Simplify the code a little. The number of bytes written is already checked in usb_write(). Signed-off-by: Tim Newsome <tim@sifive.com> Change-Id: Ibada85dcccfca6f1269c584cdbc4f2e3b93bb8f3 Reviewed-on: https://review.openocd.org/c/openocd/+/7813 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
2023-07-22target/riscv: Add null pointer check before right shift for bscan tunneling.eolson1-2/+4
Change-Id: I5d4764c777f33d48705b3e5273eb840c13cfbfb7 Signed-off-by: eolson <erin.olson@seagate.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7814 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
2023-07-22target/arc: fix off-by-one error in arc_save_context()Artemiy Volkov1-14/+10
While not affecting the function's main purpose, an error has crept into arc_save_context() that results in logging wrong register values when the debug level is 3 or more. For instance, when debugging a trivial program and halting at entry to main, the following values are printed to the log: Debug: 2915 2020 arc.c:894 arc_save_context(): Get core register regnum=0, name=r0, value=0x0000000 ... Debug: 2947 2020 arc.c:894 arc_save_context(): Get core register regnum=60, name=lp_count, value=0x900002d8 Debug: 2948 2020 arc.c:894 arc_save_context(): Get core register regnum=63, name=pcl, value=0xffffffff Debug: 2949 2020 arc.c:909 arc_save_context(): Get aux register regnum=64, name=pc, value=0x900000b4 Debug: 2950 2020 arc.c:909 arc_save_context(): Get aux register regnum=65, name=lp_start, value=0x900000bc Debug: 2951 2020 arc.c:909 arc_save_context(): Get aux register regnum=66, name=lp_end, value=0x00080801 Debug: 2952 2020 arc.c:909 arc_save_context(): Get aux register regnum=67, name=status32, value=0xffffffff After the change, the register contents make much more sense: Debug: 2923 3934 arc.c:889 arc_save_context(): Get core register regnum=0, name=r0, value=0x00000000 ... Debug: 2955 3934 arc.c:889 arc_save_context(): Get core register regnum=60, name=lp_count, value=0x00000000 Debug: 2956 3934 arc.c:889 arc_save_context(): Get core register regnum=63, name=pcl, value=0x900002d8 Debug: 2957 3934 arc.c:903 arc_save_context(): Get aux register regnum=64, name=pc, value=0x900002da Debug: 2958 3934 arc.c:903 arc_save_context(): Get aux register regnum=65, name=lp_start, value=0x900000b4 Debug: 2959 3934 arc.c:903 arc_save_context(): Get aux register regnum=66, name=lp_end, value=0x900000bc Debug: 2960 3934 arc.c:903 arc_save_context(): Get aux register regnum=67, name=status32, value=0x00080801 While at it, simplify a couple of expressions. Change-Id: I8f2d79404707fbac4503af45b393ea73f91e6beb Signed-off-by: Artemiy Volkov <artemiy@synopsys.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7765 Tested-by: jenkins Reviewed-by: Evgeniy Didin <didin@synopsys.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14tcl/board: add esp32s3-builtin.cfg fileErhan Kurubas1-0/+15
Board config file for ESP32-S3, to allow communication with the builtin USB-JTAG adapter. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I1310f5db30f7df38fe9344f7ba2334611b53863e Reviewed-on: https://review.openocd.org/c/openocd/+/7749 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-07-14tcl/interface: add Espressif builtin usb_jtag config file.Erhan Kurubas1-0/+9
This config file enables communication over USB-JTAG with ESP32-C3, ESP32-S3, ESP32-H2 and ESP32-C6 chips Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: Iceea26972588d8c4919d1f3248684ece48ca9121 Reviewed-on: https://review.openocd.org/c/openocd/+/7748 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14target/espressif: cleanup unused macro definitionsErhan Kurubas3-43/+0
Memory region addresses are not in use for now. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I9a2189e956ae59b56245ec914ab16719df857b2d Reviewed-on: https://review.openocd.org/c/openocd/+/7762 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14target/espressif: read entry addresses of pre-defined stub functionsErhan Kurubas6-21/+300
Debug stubs functionality provided by ESP IDF allows executing target function in any address. e.g; esp32_cmd_gcov() Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I56d844e5a862c9bf33fdb991b01abb7a76047ca7 Reviewed-on: https://review.openocd.org/c/openocd/+/7758 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14target/esp_xtensa: add xtensa on_halt handlerErhan Kurubas7-3/+35
Right after target halt, some activities needs to be done such as printing exception reason, disable wdts and reading debug stubs information. Missing activities will be submitted in the next patches. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I27aad5614d903f4bd7c8d6dba6bfb0bdb93ed8dc Reviewed-on: https://review.openocd.org/c/openocd/+/7757 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-07-14tcl/target: update esp32s3.cfg to reference shared functions in the ↵Erhan Kurubas1-92/+12
esp_common.cfg This commit enhances code reusability, simplifies maintenance, and ensures consistency across all chip configurations by consolidating commonly used commands and variables into the common config file. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: Ifb0122f3b98a767f27746409499733b70fb7d0e8 Reviewed-on: https://review.openocd.org/c/openocd/+/7747 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14tcl/target: update esp32s2.cfg to reference shared functions in the ↵Erhan Kurubas1-50/+12
esp_common.cfg This commit enhances code reusability, simplifies maintenance, and ensures consistency across all chip configurations by consolidating commonly used commands and variables into the common config file. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I36c86fe4ebc99928ce48a5bff8cb9580a0fa3ac0 Reviewed-on: https://review.openocd.org/c/openocd/+/7746 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14tcl/target: update esp32.cfg to reference shared functions in the esp_common.cfgErhan Kurubas1-79/+15
This commit enhances code reusability, simplifies maintenance, and ensures consistency across all chip configurations by consolidating commonly used commands and variables into the common config file. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I9181737d83eeba4e983b6a455b8a1523f2576dd2 Reviewed-on: https://review.openocd.org/c/openocd/+/7745 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-07-14tcl/target: move Espressif shared functions to esp_common.cfgErhan Kurubas1-3/+182
Consolidate commonly used commands and variables from chip config files into functions in esp_common.cfg. This includes "jtag newtap," "target create,"and "configure -event." Enhances code reusability and simplifies maintenance. Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: I9e8bf07a4a15d4544ceb564607dea66837381d70 Reviewed-on: https://review.openocd.org/c/openocd/+/7744 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14doc:usb_adapters: add lsusb dump of STLINK-V3PWRAntonio Borneo2-0/+324
Add USB VID:PID 0483:3755 and 0483:3757. Change-Id: Iace29fa97f1b8e9d86078b9775561ca525635523 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7768 Tested-by: jenkins
2023-07-14ipdbg: fix 'double free' in case of failed startDaniel Anselmi1-3/+1
Change-Id: Id241d9dd0793095106fea000422617fbef462669 Signed-off-by: Daniel Anselmi <danselmi@gmx.ch> Reviewed-on: https://review.openocd.org/c/openocd/+/7770 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-07-14flash/nor/stm32l4x: Add revision 'V' for STM32L4R/S devicesMarc Schink1-0/+1
See section 57.6.1 in RM0432. Change-Id: Ic4977aee74d1838f420c1d9ff19925d09f8f6e2b Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: https://review.openocd.org/c/openocd/+/7763 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14tcl/ultrascale: add more ultrascale devicesDaniel Anselmi1-26/+73
Add more ultrascale devices. Set instruction codes for SSI devices such that refresh/program read_stat and user registers will work. Change-Id: Id0a0706f4016eb8a4732725a5b72ae61efd73421 Signed-off-by: Daniel Anselmi <danselmi@gmx.ch> Reviewed-on: https://review.openocd.org/c/openocd/+/7716 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2023-07-14tcl/cpld: add config files for virtex-7 devices with ir-length > 6Daniel Anselmi4-9/+90
Adding a single file for each different ir-length. Change-Id: Iba3dd55b91c28fdb4d0cafa1ededd939fe61a267 Signed-off-by: Daniel Anselmi <danselmi@gmx.ch> Reviewed-on: https://review.openocd.org/c/openocd/+/7715 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2023-07-13target/espressif: fix build issue with older gcc versionsErhan Kurubas1-1/+1
Compilation on old gcc 4.8.4 fails: error: missing braces around initializer [-Werror=missing-braces] Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: Ie8b5747f9e23ba5a82bd7f666846e7286284a338 Reviewed-on: https://review.openocd.org/c/openocd/+/7815 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2023-07-08jtag/stlink: add STLINK-V3PWR supportLaurent LEMELE5-6/+53
STLINK-V3PWR is both a standalone debugger probe compatible with STLINK-V3 and a source measurement unit (SMU). Link: http://www.st.com/stlink-v3pwr This code adds support for the debugger probe functionality. Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1 Signed-off-by: Laurent LEMELE <laurent.lemele@st.com> Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7755 Tested-by: jenkins
generated by cgit v1.1 at 2024-09-18 09:41:03 +0000