9 files changed, 18 insertions, 18 deletions
diff --git a/tcl/board/hitex_str9-comstick.cfg b/tcl/board/hitex_str9-comstick.cfg
index 4d1bb2e..c85681b 100644
--- a/tcl/board/hitex_str9-comstick.cfg
+++ b/tcl/board/hitex_str9-comstick.cfg
@@ -73,7 +73,7 @@ $_TARGETNAME configure -event reset-init {
 $_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
 
 #flash bank <driver> <base> <size> <chip_width> <bus_width>
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 0
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 0
diff --git a/tcl/board/lubbock.cfg b/tcl/board/lubbock.cfg
index 095c60a..b58ad5a 100644
--- a/tcl/board/lubbock.cfg
+++ b/tcl/board/lubbock.cfg
@@ -12,9 +12,9 @@ jtag_ntrst_delay 250
 
 # CS0, CS1 -- two banks of CFI flash, 32 MBytes each
 # each bank is 32-bits wide, two 16-bit chips in parallel
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME cfi 0x00000000 0x02000000 2 4 $_TARGETNAME
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME cfi 0x04000000 0x02000000 2 4 $_TARGETNAME
 
 # CS2 low -- FPGA registers
diff --git a/tcl/board/str910-eval.cfg b/tcl/board/str910-eval.cfg
index a2772a8..9e3f881 100644
--- a/tcl/board/str910-eval.cfg
+++ b/tcl/board/str910-eval.cfg
@@ -58,9 +58,9 @@ $_TARGETNAME configure -event reset-init {
 }
 
 #flash bank str9x <base> <size> 0 0 <target#> <variant>
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 0
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 0
 
 # For more information about the configuration files, take a look at:
diff --git a/tcl/target/at91sam3u4c.cfg b/tcl/target/at91sam3u4c.cfg
index e281287..5cacbcb 100644
--- a/tcl/target/at91sam3u4c.cfg
+++ b/tcl/target/at91sam3u4c.cfg
@@ -2,10 +2,10 @@
 source [find target/at91sam3uxx.cfg]
 
 # size is automatically "calculated" by probing
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME at91sam3 0x000080000 0 1 1 $_TARGETNAME
 # This is a 256K chip, it has the 2nd bank
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME at91sam3 0x000100000 0 1 1 $_TARGETNAME
 
 
diff --git a/tcl/target/at91sam3u4e.cfg b/tcl/target/at91sam3u4e.cfg
index e549185..6f6e0d8 100644
--- a/tcl/target/at91sam3u4e.cfg
+++ b/tcl/target/at91sam3u4e.cfg
@@ -2,10 +2,10 @@
 source [find target/at91sam3uXX.cfg]
 
 # size is automatically "calculated" by probing
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME at91sam3 0x000080000 0 1 1 $_TARGETNAME
 # This is a 256K chip - it has the 2nd bank
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME at91sam3 0x000100000 0 1 1 $_TARGETNAME
 
 
diff --git a/tcl/target/pic32mx.cfg b/tcl/target/pic32mx.cfg
index 673d254..0b99cdb 100644
--- a/tcl/target/pic32mx.cfg
+++ b/tcl/target/pic32mx.cfg
@@ -67,9 +67,9 @@ $_TARGETNAME configure -event reset-init {
 	mww 0xbf882030 $_PIC32MX_PROGSIZE
 }
 
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME pic32mx 0x1fc00000 0 0 0 $_TARGETNAME
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME pic32mx 0x1d000000 0 0 0 $_TARGETNAME
 
 # For more information about the configuration files, take a look at:
diff --git a/tcl/target/str710.cfg b/tcl/target/str710.cfg
index 4d68586..a5955b6 100644
--- a/tcl/target/str710.cfg
+++ b/tcl/target/str710.cfg
@@ -47,9 +47,9 @@ $_TARGETNAME configure -event gdb-flash-erase-start {
 $_TARGETNAME configure -work-area-phys 0x2000C000 -work-area-size 0x4000 -work-area-backup 0
 
 #flash bank str7x <base> <size> 0 0 <target#> <variant>
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME str7x 0x40000000 0x00040000 0 0 $_TARGETNAME STR71x
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME str7x 0x400C0000 0x00004000 0 0 $_TARGETNAME STR71x
 
 # For more information about the configuration files, take a look at:
diff --git a/tcl/target/str750.cfg b/tcl/target/str750.cfg
index 8a64226..7d9f034 100644
--- a/tcl/target/str750.cfg
+++ b/tcl/target/str750.cfg
@@ -53,8 +53,8 @@ $_TARGETNAME configure -event gdb-flash-erase-start {
 $_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0
 
 #flash bank <driver> <base> <size> <chip_width> <bus_width>
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME str7x 0x20000000 0x00040000 0 0 $_TARGETNAME STR75x
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME str7x 0x200C0000 0x00004000 0 0 $_TARGETNAME STR75x
 
diff --git a/tcl/target/str912.cfg b/tcl/target/str912.cfg
index 6f2981a..a16c83a 100644
--- a/tcl/target/str912.cfg
+++ b/tcl/target/str912.cfg
@@ -63,9 +63,9 @@ $_TARGETNAME configure -event reset-init {
 $_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
 
 #flash bank str9x <base> <size> 0 0 <target#> <variant>
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 $_TARGETNAME
-set _FLASHNAME $_CHIPNAME.flash
+set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 $_TARGETNAME
 
 # For more information about the configuration files, take a look at: