diff options
Diffstat (limited to 'doc/openocd.texi')
-rw-r--r-- | doc/openocd.texi | 25 |
1 files changed, 12 insertions, 13 deletions
diff --git a/doc/openocd.texi b/doc/openocd.texi index 8ffbcf3..a0c8ebb 100644 --- a/doc/openocd.texi +++ b/doc/openocd.texi @@ -7345,12 +7345,13 @@ flash bank $_FLASHNAME npcx 0x64000000 0 0 0 $_TARGETNAME @end deffn @deffn {Flash Driver} {nrf5} -All members of the nRF51 microcontroller families from Nordic Semiconductor -include internal flash and use ARM Cortex-M0 core. nRF52 family powered -by ARM Cortex-M4 or M4F core is supported too. nRF52832 is fully supported -including BPROT flash protection scheme. nRF52833 and nRF52840 devices are -supported with the exception of security extensions (flash access control list -- ACL). +Supports all members of the nRF51, nRF52 and nRF53 microcontroller families from +Nordic Semiconductor. nRF91 family is supported too. One driver handles both +the main flash and the UICR area. + +Flash protection is handled on nRF51 family and nRF52805, nRF52810, nRF52811, +nRF52832 devices. Flash access control list (ACL) protection scheme of the newer +devices is not supported. @example flash bank $_FLASHNAME nrf5 0 0x00000000 0 0 $_TARGETNAME @@ -8827,8 +8828,8 @@ The file format must be inferred by the driver. @section PLD/FPGA Drivers, Options, and Commands -Drivers may support PLD-specific options to the @command{pld device} -definition command, and may also define commands usable only with +Drivers may support PLD-specific options to the @command{pld create} +command, and may also define commands usable only with that particular type of PLD. @deffn {FPGA Driver} {virtex2} [@option{-no_jstart}] @@ -8914,13 +8915,12 @@ For the option @option{-family} @var{name} is one of @var{trion|titanium}. @end deffn -@deffn {FPGA Driver} {intel} [@option{-family} <name>] +@deffn {FPGA Driver} {intel} @option{-family} <name> This driver can be used to load the bitstream into Intel (former Altera) FPGAs. -The families Cyclone III, Cyclone IV, Cyclone V, Cyclone 10, Arria II are supported. +The families Cyclone III, Cyclone IV, Cyclone V, Cyclone 10 and Arria II are supported. @c Arria V and Arria 10, MAX II, MAX V, MAX10) -For the option @option{-family} @var{name} is one of @var{cycloneiii cycloneiv cyclonev cyclone10 arriaii}. -This is needed when the JTAG ID of the device is ambiguous (same ID is used for chips in different families). +The option @option{-family} @var{name} is one of @var{cycloneiii cycloneiv cyclonev cyclone10 arriaii}. As input file format the driver supports a '.rbf' (raw bitstream file) file. The '.rbf' file can be generated from a '.sof' file with @verb{|quartus_cpf -c blinker.sof blinker.rbf|} @@ -11376,7 +11376,6 @@ tunneled DR scan consists of: @item A width+1 stream of bits for the tunneled TDI. The plus one is because there is a one-clock skew between TDI of Xilinx chain and TDO from tunneled chain. @item 3 bits of zero that the tunnel uses to go back to idle state. @end enumerate - @end deffn @deffn {Command} {riscv set_bscan_tunnel_ir} value |