Add LPC8Nxx and NHS3xx support.

Change-Id: I0bdbca8dd9b234aca355230af7269463c9f70bd1
Signed-off-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-on: http://openocd.zylin.com/4515
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>

2 files changed, 85 insertions, 0 deletions

diff --git a/tcl/target/lpc8nxx.cfg b/tcl/target/lpc8nxx.cfg
new file mode 100644
index 0000000..b933290
--- /dev/null
+++ b/tcl/target/lpc8nxx.cfg
@@ -0,0 +1,81 @@
+# NXP LPC8Nxx NHS31xx Cortex-M0+ with 8kB SRAM
+# Copyright (C) 2018 by Jean-Christian de Rivaz
+# Based on NXP proposal https://community.nxp.com/message/1011149
+# Many thanks to Dries Moors from NXP support.
+# SWD only transport
+
+source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
+
+if { [info exists CHIPNAME] } {
+	set  _CHIPNAME $CHIPNAME
+} else {
+	set  _CHIPNAME lpc8nxx
+}
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id 0
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m -endian little -dap $_CHIPNAME.dap
+if {![using_hla]} {
+	# If srst is not fitted use SYSRESETREQ to  perform a soft reset
+	cortex_m reset_config sysresetreq
+}
+adapter_nsrst_delay 100
+
+$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x1ff0 -work-area-backup 0
+
+flash bank $_CHIPNAME.flash lpc2000 0x0 0x7800 0 0 $_TARGETNAME lpc800 500
+
+echo "*********************************************************************************"
+echo "*         !!!!! IMPORTANT NOTICE FOR LPC8Nxx and NHS31xx CHIPS !!!!!"
+echo "* When this IC is in power-off or peep power down mode, the SWD HW block is also"
+echo "* unpowered. These modes can be entered by firmware. The default firmware image"
+echo "* (flashed in production) makes use of this. Best is to avoid these power modes"
+echo "* during development, and only later add them when the functionality is complete."
+echo "* Hardware reset or NFC field are the only ways to connect in case the SWD is"
+echo "* powered off. OpenOCD can do a hardware reset if you wire the adapter SRST"
+echo "* signal to the chip RESETN pin and add the following in your configuration:"
+echo "*     reset_config srst_only; flash init; catch init; reset"
+echo "* But if the actual firmware immediately set the power down mode after reset,"
+echo "* OpenOCD might be not fast enough to halt the CPU before the SWD lost power. In"
+echo "* that case the only solution is to apply a NFC field to keep the SWD powered."
+echo "*********************************************************************************"
+
+# Using soft-reset 'reset_config none' is strongly discouraged.
+# RESETN sets the system clock to 500 kHz. Unlike soft-reset does not.
+# Set the system clock to 500 kHz before reset to simulate the functionality of hw reset.
+#
+proc set_sysclk_500khz {} {
+	set SYSCLKCTRL 0x40048020
+	set SYSCLKUEN 0x40048024
+	mww $SYSCLKUEN 0
+	mmw $SYSCLKCTRL 0x8 0xe
+	mww $SYSCLKUEN 1
+	echo "Notice: sysclock set to 500kHz."
+}
+
+# Do not remap the ARM interrupt vectors to anything but the beginning ot the flash.
+# Table System memory remap register (SYSMEMREMAP, address 0x4004 8000) bit description
+# Bit Symbol  Value   Description
+# 0   map         -   interrupt vector remap. 0 after boot.
+#                 0   interrupt vector reside in Flash
+#                 1   interrupt vector reside in SRAM
+# 5:1 offset      -   system memory remap offset. 00000b after boot.
+#            00000b   interrupt vectors in flash or remapped to SRAM but no offset
+#            00001b -
+#            00111b   interrupt vectors offset in flash or SRAM to 1K word segment
+#            01000b -
+#            11111b   interrupt vectors offset in flash to 1K word segment 8 to 31
+# 31:6                reserved
+#
+proc set_no_remap {} {
+	mww 0x40048000 0x00
+	echo "Notice: interrupt vector set to no remap."
+}
+
+$_TARGETNAME configure -event reset-init {
+	set_sysclk_500khz
+	set_no_remap
+}
diff --git a/tcl/target/nhs31xx.cfg b/tcl/target/nhs31xx.cfg
new file mode 100644
index 0000000..964be7b
--- /dev/null
+++ b/tcl/target/nhs31xx.cfg
@@ -0,0 +1,4 @@
+# NXP NHS31xx Cortex-M0+ with 8kB SRAM
+
+set CHIPNAME nhs31xx
+source [find target/lpc8nxx.cfg]