diff options
author | Palmer Dabbelt <palmer@dabbelt.com> | 2017-03-21 12:02:10 -0700 |
---|---|---|
committer | Palmer Dabbelt <palmer@dabbelt.com> | 2017-03-21 17:20:11 -0700 |
commit | 0c790d385d082d6d8bec5c1dbd1fb2c139e91435 (patch) | |
tree | de8b35c1b14a8468d0a50c6466dc3b19d43a7108 /src | |
parent | c09ccbcc7c6272db2703422beb78236d23ace41b (diff) | |
download | riscv-openocd-0c790d385d082d6d8bec5c1dbd1fb2c139e91435.zip riscv-openocd-0c790d385d082d6d8bec5c1dbd1fb2c139e91435.tar.gz riscv-openocd-0c790d385d082d6d8bec5c1dbd1fb2c139e91435.tar.bz2 |
Builds
Diffstat (limited to 'src')
-rw-r--r-- | src/target/riscv/debug_defines.h | 831 | ||||
-rw-r--r-- | src/target/riscv/riscv-013.c | 127 |
2 files changed, 533 insertions, 425 deletions
diff --git a/src/target/riscv/debug_defines.h b/src/target/riscv/debug_defines.h index 2e0c192..ec535db 100644 --- a/src/target/riscv/debug_defines.h +++ b/src/target/riscv/debug_defines.h @@ -24,14 +24,14 @@ #define DTM_IDCODE_1_OFFSET 0 #define DTM_IDCODE_1_LENGTH 1 #define DTM_IDCODE_1 (0x1 << DTM_IDCODE_1_OFFSET) -#define DTM_DTMCONTROL 0x10 +#define DTM_DTMCS 0x10 /* * Writing 1 to this bit resets the DMI controller, clearing any * sticky error state. */ -#define DTM_DTMCONTROL_DMIRESET_OFFSET 16 -#define DTM_DTMCONTROL_DMIRESET_LENGTH 1 -#define DTM_DTMCONTROL_DMIRESET (0x1 << DTM_DTMCONTROL_DMIRESET_OFFSET) +#define DTM_DTMCS_DMIRESET_OFFSET 16 +#define DTM_DTMCS_DMIRESET_LENGTH 1 +#define DTM_DTMCS_DMIRESET (0x1 << DTM_DTMCS_DMIRESET_OFFSET) /* * This is the minimum number of cycles a debugger should spend in * Run-Test/Idle after every DMI scan to avoid a 'busy' @@ -46,9 +46,9 @@ * * And so on. */ -#define DTM_DTMCONTROL_IDLE_OFFSET 12 -#define DTM_DTMCONTROL_IDLE_LENGTH 3 -#define DTM_DTMCONTROL_IDLE (0x7 << DTM_DTMCONTROL_IDLE_OFFSET) +#define DTM_DTMCS_IDLE_OFFSET 12 +#define DTM_DTMCS_IDLE_LENGTH 3 +#define DTM_DTMCS_IDLE (0x7 << DTM_DTMCS_IDLE_OFFSET) /* * 0: No error. * @@ -59,15 +59,15 @@ * 3: An operation was attempted while a DMI access was still in * progress (resulted in \Fop of 3). */ -#define DTM_DTMCONTROL_DMISTAT_OFFSET 10 -#define DTM_DTMCONTROL_DMISTAT_LENGTH 2 -#define DTM_DTMCONTROL_DMISTAT (0x3 << DTM_DTMCONTROL_DMISTAT_OFFSET) +#define DTM_DTMCS_DMISTAT_OFFSET 10 +#define DTM_DTMCS_DMISTAT_LENGTH 2 +#define DTM_DTMCS_DMISTAT (0x3 << DTM_DTMCS_DMISTAT_OFFSET) /* * The size of \Faddress in \Rdmi. */ -#define DTM_DTMCONTROL_ABITS_OFFSET 4 -#define DTM_DTMCONTROL_ABITS_LENGTH 6 -#define DTM_DTMCONTROL_ABITS (0x3f << DTM_DTMCONTROL_ABITS_OFFSET) +#define DTM_DTMCS_ABITS_OFFSET 4 +#define DTM_DTMCS_ABITS_LENGTH 6 +#define DTM_DTMCS_ABITS (0x3f << DTM_DTMCS_ABITS_OFFSET) /* * 0: Version described in spec version 0.11. * @@ -76,9 +76,9 @@ * * Other values are reserved for future use. */ -#define DTM_DTMCONTROL_VERSION_OFFSET 0 -#define DTM_DTMCONTROL_VERSION_LENGTH 4 -#define DTM_DTMCONTROL_VERSION (0xf << DTM_DTMCONTROL_VERSION_OFFSET) +#define DTM_DTMCS_VERSION_OFFSET 0 +#define DTM_DTMCS_VERSION_LENGTH 4 +#define DTM_DTMCS_VERSION (0xf << DTM_DTMCS_VERSION_OFFSET) #define DTM_DMI 0x11 /* * Address used for DMI access. In Update-DR this value is used @@ -113,7 +113,7 @@ * * 2: A previous operation failed. The data scanned into \Rdmi in * this access will be ignored. This status is sticky and can be -* cleared by writing \Fdmireset in \Rdtmcontrol. +* cleared by writing \Fdmireset in \Rdtmcs. * * This indicates that the DM itself responded with an error, e.g. * in the System Bus and Serial Port overflow/underflow cases. @@ -121,7 +121,7 @@ * 3: An operation was attempted while a DMI request is still in * progress. The data scanned into \Rdmi in this access will be * ignored. This status is sticky and can be cleared by writing -* \Fdmireset in \Rdtmcontrol. If a debugger sees this status, it +* \Fdmireset in \Rdtmcs. If a debugger sees this status, it * needs to give the target more TCK edges between Update-DR and * Capture-DR. The simplest way to do that is to add extra transitions * in Run-Test/Idle. @@ -171,23 +171,23 @@ #define CSR_DCSR_EBREAKU_LENGTH 1 #define CSR_DCSR_EBREAKU (0x1 << CSR_DCSR_EBREAKU_OFFSET) /* -* Controls the behavior of any counters while the component is in -* Halt Mode. This includes the {\tt cycle} and {\tt instret} CSRs. -* When 1, counters are stopped when the component is in Halt Mode. -* Otherwise, the counters continue to run. +* 0: Increment counters as usual. +* +* 1: Don't increment any counters while in Halt Mode. This includes +* the {\tt cycle} and {\tt instret} CSRs. This is preferred for most +* debugging scenarios. * * An implementation may choose not to support writing to this bit. * The debugger must read back the value it writes to check whether * the feature is supported. */ -#define CSR_DCSR_STOPCYCLE_OFFSET 10 -#define CSR_DCSR_STOPCYCLE_LENGTH 1 -#define CSR_DCSR_STOPCYCLE (0x1 << CSR_DCSR_STOPCYCLE_OFFSET) +#define CSR_DCSR_STOPCOUNT_OFFSET 10 +#define CSR_DCSR_STOPCOUNT_LENGTH 1 +#define CSR_DCSR_STOPCOUNT (0x1 << CSR_DCSR_STOPCOUNT_OFFSET) /* -* Controls the behavior of any timers while the component is in Debug -* Mode. This includes the {\tt time} and {tt timeh} CSRs. When 1, -* timers are stopped when the component is in Halt Mode. Otherwise, -* the timers continue to run. +* 0: Increment timers as usual. +* +* 1: Don't increment any hart-local timers while in Halt Mode. * * An implementation may choose not to support writing to this bit. * The debugger must read back the value it writes to check whether @@ -324,7 +324,7 @@ #define CSR_MCONTROL_MASKMAX_LENGTH 6 #define CSR_MCONTROL_MASKMAX (0x3fL << CSR_MCONTROL_MASKMAX_OFFSET) /* -* 0: Perform a match on the address. +* 0: Perform a match on the virtual address. * * 1: Perform a match on the data value loaded/stored, or the * instruction executed. @@ -350,7 +350,7 @@ * * Data load triggers with \Ftiming of 0 will result in the same load * happening again when the debugger lets the core run. For data load -* triggers debuggers must first attempt to set the breakpoint with +* triggers, debuggers must first attempt to set the breakpoint with * \Ftiming of 1. * * A chain of triggers that don't all have the same \Ftiming value @@ -439,20 +439,20 @@ #define CSR_MCONTROL_U_LENGTH 1 #define CSR_MCONTROL_U (0x1L << CSR_MCONTROL_U_OFFSET) /* -* When set, the trigger fires on the address or opcode of an +* When set, the trigger fires on the virtual address or opcode of an * instruction that is executed. */ #define CSR_MCONTROL_EXECUTE_OFFSET 2 #define CSR_MCONTROL_EXECUTE_LENGTH 1 #define CSR_MCONTROL_EXECUTE (0x1L << CSR_MCONTROL_EXECUTE_OFFSET) /* -* When set, the trigger fires on the address or data of a store. +* When set, the trigger fires on the virtual address or data of a store. */ #define CSR_MCONTROL_STORE_OFFSET 1 #define CSR_MCONTROL_STORE_LENGTH 1 #define CSR_MCONTROL_STORE (0x1L << CSR_MCONTROL_STORE_OFFSET) /* -* When set, the trigger fires on the address or data of a load. +* When set, the trigger fires on the virtual address or data of a load. */ #define CSR_MCONTROL_LOAD_OFFSET 0 #define CSR_MCONTROL_LOAD_LENGTH 1 @@ -522,64 +522,171 @@ #define CSR_ICOUNT_ACTION_OFFSET 0 #define CSR_ICOUNT_ACTION_LENGTH 6 #define CSR_ICOUNT_ACTION (0x3fL << CSR_ICOUNT_ACTION_OFFSET) -#define DMI_DMCONTROL 0x00 +#define DMI_DMSTATUS 0x11 +/* +* This field is 1 when all currently selected harts do not exist in this system. + */ +#define DMI_DMSTATUS_ALLNONEXISTENT_OFFSET 15 +#define DMI_DMSTATUS_ALLNONEXISTENT_LENGTH 1 +#define DMI_DMSTATUS_ALLNONEXISTENT (0x1 << DMI_DMSTATUS_ALLNONEXISTENT_OFFSET) +/* +* This field is 1 when any currently selected hart does not exist in this system. + */ +#define DMI_DMSTATUS_ANYNONEXISTENT_OFFSET 14 +#define DMI_DMSTATUS_ANYNONEXISTENT_LENGTH 1 +#define DMI_DMSTATUS_ANYNONEXISTENT (0x1 << DMI_DMSTATUS_ANYNONEXISTENT_OFFSET) +/* +* This field is 1 when all currently selected harts are unavailable. + */ +#define DMI_DMSTATUS_ALLUNAVAIL_OFFSET 13 +#define DMI_DMSTATUS_ALLUNAVAIL_LENGTH 1 +#define DMI_DMSTATUS_ALLUNAVAIL (0x1 << DMI_DMSTATUS_ALLUNAVAIL_OFFSET) +/* +* This field is 1 when any currently selected hart is unavailable. + */ +#define DMI_DMSTATUS_ANYUNAVAIL_OFFSET 12 +#define DMI_DMSTATUS_ANYUNAVAIL_LENGTH 1 +#define DMI_DMSTATUS_ANYUNAVAIL (0x1 << DMI_DMSTATUS_ANYUNAVAIL_OFFSET) +/* +* This field is 1 when all currently selected harts are running. + */ +#define DMI_DMSTATUS_ALLRUNNING_OFFSET 11 +#define DMI_DMSTATUS_ALLRUNNING_LENGTH 1 +#define DMI_DMSTATUS_ALLRUNNING (0x1 << DMI_DMSTATUS_ALLRUNNING_OFFSET) +/* +* This field is 1 when any currently selected hart is running. + */ +#define DMI_DMSTATUS_ANYRUNNING_OFFSET 10 +#define DMI_DMSTATUS_ANYRUNNING_LENGTH 1 +#define DMI_DMSTATUS_ANYRUNNING (0x1 << DMI_DMSTATUS_ANYRUNNING_OFFSET) +/* +* This field is 1 when all currently selected harts are halted. + */ +#define DMI_DMSTATUS_ALLHALTED_OFFSET 9 +#define DMI_DMSTATUS_ALLHALTED_LENGTH 1 +#define DMI_DMSTATUS_ALLHALTED (0x1 << DMI_DMSTATUS_ALLHALTED_OFFSET) +/* +* This field is 1 when any currently selected hart is halted. + */ +#define DMI_DMSTATUS_ANYHALTED_OFFSET 8 +#define DMI_DMSTATUS_ANYHALTED_LENGTH 1 +#define DMI_DMSTATUS_ANYHALTED (0x1 << DMI_DMSTATUS_ANYHALTED_OFFSET) +/* +* 0 when authentication is required before using the DM. 1 when the +* authentication check has passed. On components that don't implement +* authentication, this bit must be preset as 1. + */ +#define DMI_DMSTATUS_AUTHENTICATED_OFFSET 7 +#define DMI_DMSTATUS_AUTHENTICATED_LENGTH 1 +#define DMI_DMSTATUS_AUTHENTICATED (0x1 << DMI_DMSTATUS_AUTHENTICATED_OFFSET) +/* +* 0: The authentication module is ready to process the next +* read/write to \Rauthdata. +* +* 1: The authentication module is busy. Accessing \Rauthdata results +* in unspecified behavior. +* +* \Fauthbusy only becomes set in immediate response to an access to +* \Rauthdata. + */ +#define DMI_DMSTATUS_AUTHBUSY_OFFSET 6 +#define DMI_DMSTATUS_AUTHBUSY_LENGTH 1 +#define DMI_DMSTATUS_AUTHBUSY (0x1 << DMI_DMSTATUS_AUTHBUSY_OFFSET) +#define DMI_DMSTATUS_CFGSTRVALID_OFFSET 4 +#define DMI_DMSTATUS_CFGSTRVALID_LENGTH 1 +#define DMI_DMSTATUS_CFGSTRVALID (0x1 << DMI_DMSTATUS_CFGSTRVALID_OFFSET) +/* +* Reserved for future use. Reads as 0. + */ +#define DMI_DMSTATUS_VERSIONHI_OFFSET 2 +#define DMI_DMSTATUS_VERSIONHI_LENGTH 2 +#define DMI_DMSTATUS_VERSIONHI (0x3 << DMI_DMSTATUS_VERSIONHI_OFFSET) +/* +* 00: There is no Debug Module present. +* +* 01: There is a Debug Module and it conforms to version 0.11 of this +* specification. +* +* 10: There is a Debug Module and it conforms to version 0.13 of this +* specification. +* +* 11: Reserved for future use. + */ +#define DMI_DMSTATUS_VERSIONLO_OFFSET 0 +#define DMI_DMSTATUS_VERSIONLO_LENGTH 2 +#define DMI_DMSTATUS_VERSIONLO (0x3 << DMI_DMSTATUS_VERSIONLO_OFFSET) +#define DMI_DMCONTROL 0x10 /* -* Halt request signal for the hart selected by \Fhartsel. When 1, the -* hart will halt if it's not currently halted. +* Halt request signal for all currently selected harts. When 1, the +* hart will halt if it is not currently halted. * Setting both \Fhaltreq and \Fresumereq leads to undefined behavior. * -* Writes apply to the new value of \Fhartsel. +* Writes apply to the new value of \Fhartsel and \Fhasel. */ #define DMI_DMCONTROL_HALTREQ_OFFSET 31 #define DMI_DMCONTROL_HALTREQ_LENGTH 1 #define DMI_DMCONTROL_HALTREQ (0x1 << DMI_DMCONTROL_HALTREQ_OFFSET) /* -* Resume request signal for the hart selected by \Fhartsel. When 1, -* the hart will resume if it's currently halted. +* Resume request signal for all currently selected harts. When 1, +* the hart will resume if it is currently halted. * Setting both \Fhaltreq and \Fresumereq leads to undefined behavior. * -* Writes apply to the new value of \Fhartsel. +* Writes apply to the new value of \Fhartsel and \Fhasel. */ #define DMI_DMCONTROL_RESUMEREQ_OFFSET 30 #define DMI_DMCONTROL_RESUMEREQ_LENGTH 1 #define DMI_DMCONTROL_RESUMEREQ (0x1 << DMI_DMCONTROL_RESUMEREQ_OFFSET) /* -* The status of the currently selected hart. +* This optional bit controls reset to all the currently selected harts. +* To perform a reset the debugger writes 1, and then writes 0 to +* deassert the reset signal. +* +* If this feature is not implemented, the bit always stays 0, so +* after writing 1 the debugger can read the register back to see if +* the feature is supported. * -* 0: Halted. +* Writes apply to the new value of \Fhartsel and \Fhasel. + */ +#define DMI_DMCONTROL_HARTRESET_OFFSET 29 +#define DMI_DMCONTROL_HARTRESET_LENGTH 1 +#define DMI_DMCONTROL_HARTRESET (0x1 << DMI_DMCONTROL_HARTRESET_OFFSET) +/* +* Selects the definition of currently selected harts. * -* 1: Running. +* 0: There is a single currently selected hart, that selected by \Fhartsel. * -* 2: Unavailable (eg. powered down, held in reset). +* 1: There may be multiple currently selected harts -- that selected by \Fhartsel, +* plus those selected by the hart array mask register. * -* 3: \Fhartsel specifies a hart that does not exist in this system. +* An implementation which does not implement the hart array mask register +* should tie this field to 0. A debugger which wishes to use the hart array +* mask register feature should set this bit and read back to see if the functionality +* is supported. */ -#define DMI_DMCONTROL_HARTSTATUS_OFFSET 26 -#define DMI_DMCONTROL_HARTSTATUS_LENGTH 2 -#define DMI_DMCONTROL_HARTSTATUS (0x3 << DMI_DMCONTROL_HARTSTATUS_OFFSET) +#define DMI_DMCONTROL_HASEL_OFFSET 26 +#define DMI_DMCONTROL_HASEL_LENGTH 1 +#define DMI_DMCONTROL_HASEL (0x1 << DMI_DMCONTROL_HASEL_OFFSET) /* -* The DM-specific index of the hart to select. +* The DM-specific index of the hart to select. This hart is always part of the +* currently selected harts. */ #define DMI_DMCONTROL_HARTSEL_OFFSET 16 #define DMI_DMCONTROL_HARTSEL_LENGTH 10 #define DMI_DMCONTROL_HARTSEL (0x3ff << DMI_DMCONTROL_HARTSEL_OFFSET) /* -* This optional bit controls reset to the currently selected hart. To -* perform a reset the debugger writes 1, and then writes 0 to -* deassert the reset signal. -* -* If this feature is not implemented, the bit always stays 0, so -* after writing 1 the debugger can read the register back to see if -* the feature is supported. +* This bit controls the reset signal from the DM to the rest of the +* system. To perform a reset the debugger writes 1, and then writes 0 +* to deassert the reset. */ -#define DMI_DMCONTROL_HARTRESET_OFFSET 10 -#define DMI_DMCONTROL_HARTRESET_LENGTH 1 -#define DMI_DMCONTROL_HARTRESET (0x1 << DMI_DMCONTROL_HARTRESET_OFFSET) +#define DMI_DMCONTROL_NDMRESET_OFFSET 1 +#define DMI_DMCONTROL_NDMRESET_LENGTH 1 +#define DMI_DMCONTROL_NDMRESET (0x1 << DMI_DMCONTROL_NDMRESET_OFFSET) /* * This bit serves as a reset signal for the Debug Module itself. * -* 0: The module, including authentication mechanism, is held in -* reset. +* 0: The module's state, including authentication mechanism, +* takes its reset values (the \Fdmactive bit is the only bit which can +* be written to something other than its reset value). * * 1: The module functions normally. * @@ -594,50 +701,19 @@ * preventing the Debug Module from being power gated while debugging * is active. */ -#define DMI_DMCONTROL_DMACTIVE_OFFSET 9 +#define DMI_DMCONTROL_DMACTIVE_OFFSET 0 #define DMI_DMCONTROL_DMACTIVE_LENGTH 1 #define DMI_DMCONTROL_DMACTIVE (0x1 << DMI_DMCONTROL_DMACTIVE_OFFSET) +#define DMI_HARTINFO 0x12 /* -* This bit controls the reset signal from the DM to the rest of the -* system. To perform a reset the debugger writes 1, and then writes 0 -* to deassert the reset. - */ -#define DMI_DMCONTROL_RESET_OFFSET 8 -#define DMI_DMCONTROL_RESET_LENGTH 1 -#define DMI_DMCONTROL_RESET (0x1 << DMI_DMCONTROL_RESET_OFFSET) -/* -* 0 when authentication is required before using the DM. 1 when the -* authentication check has passed. On components that don't implement -* authentication, this bit must be preset as 1. - */ -#define DMI_DMCONTROL_AUTHENTICATED_OFFSET 7 -#define DMI_DMCONTROL_AUTHENTICATED_LENGTH 1 -#define DMI_DMCONTROL_AUTHENTICATED (0x1 << DMI_DMCONTROL_AUTHENTICATED_OFFSET) -/* -* 0: The authentication module is ready to process the next -* read/write to \Rauthdata. -* -* 1: The authentication module is busy. Accessing \Rauthdata results -* in unspecified behavior. -* -* \Fauthbusy only becomes set in immediate response to an access to -* \Rauthdata. - */ -#define DMI_DMCONTROL_AUTHBUSY_OFFSET 6 -#define DMI_DMCONTROL_AUTHBUSY_LENGTH 1 -#define DMI_DMCONTROL_AUTHBUSY (0x1 << DMI_DMCONTROL_AUTHBUSY_OFFSET) -/* -* 0: There is no Debug Module present. -* -* 1: There is a Debug Module and it conforms to version 0.12 of this -* specification. -* -* Other values are reserved for future use. +* Number of {\tt dscratch} registers available for the debugger +* to use during program buffer execution, starting from \Rdscratchzero. +* The debugger can make no assumptions about the contents of these +* registers between commands. */ -#define DMI_DMCONTROL_VERSION_OFFSET 0 -#define DMI_DMCONTROL_VERSION_LENGTH 4 -#define DMI_DMCONTROL_VERSION (0xf << DMI_DMCONTROL_VERSION_OFFSET) -#define DMI_HARTINFO 0x01 +#define DMI_HARTINFO_NSCRATCH_OFFSET 20 +#define DMI_HARTINFO_NSCRATCH_LENGTH 4 +#define DMI_HARTINFO_NSCRATCH (0xf << DMI_HARTINFO_NSCRATCH_OFFSET) /* * 0: The {\tt data} registers are shadowed in the hart by CSR * registers. Each CSR register is XLEN bits in size, and corresponds @@ -669,7 +745,7 @@ #define DMI_HARTINFO_DATAADDR_OFFSET 0 #define DMI_HARTINFO_DATAADDR_LENGTH 12 #define DMI_HARTINFO_DATAADDR (0xfff << DMI_HARTINFO_DATAADDR_OFFSET) -#define DMI_HALTSUM 0x02 +#define DMI_HALTSUM 0x13 #define DMI_HALTSUM_HALT1023_992_OFFSET 31 #define DMI_HALTSUM_HALT1023_992_LENGTH 1 #define DMI_HALTSUM_HALT1023_992 (0x1 << DMI_HALTSUM_HALT1023_992_OFFSET) @@ -766,7 +842,240 @@ #define DMI_HALTSUM_HALT31_0_OFFSET 0 #define DMI_HALTSUM_HALT31_0_LENGTH 1 #define DMI_HALTSUM_HALT31_0 (0x1 << DMI_HALTSUM_HALT31_0_OFFSET) -#define DMI_SBCS 0x03 +#define DMI_HAWINDOWSEL 0x14 +#define DMI_HAWINDOWSEL_HAWINDOWSEL_OFFSET 0 +#define DMI_HAWINDOWSEL_HAWINDOWSEL_LENGTH 5 +#define DMI_HAWINDOWSEL_HAWINDOWSEL (0x1f << DMI_HAWINDOWSEL_HAWINDOWSEL_OFFSET) +#define DMI_HAWINDOW 0x15 +#define DMI_HAWINDOW_MASKDATA_OFFSET 0 +#define DMI_HAWINDOW_MASKDATA_LENGTH 32 +#define DMI_HAWINDOW_MASKDATA (0xffffffff << DMI_HAWINDOW_MASKDATA_OFFSET) +#define DMI_ABSTRACTCS 0x16 +/* +* Size of the Program Buffer, in 32-bit words. Valid sizes are 0 - 16. +* +* TODO: Explain what can be done with each size of the buffer, to suggest +* why you would want more or less words. + */ +#define DMI_ABSTRACTCS_PROGSIZE_OFFSET 24 +#define DMI_ABSTRACTCS_PROGSIZE_LENGTH 5 +#define DMI_ABSTRACTCS_PROGSIZE (0x1f << DMI_ABSTRACTCS_PROGSIZE_OFFSET) +/* +* 1: An abstract command is currently being executed. +* +* This bit is set as soon as \Rcommand is written, and is +* not cleared until that command has completed. + */ +#define DMI_ABSTRACTCS_BUSY_OFFSET 12 +#define DMI_ABSTRACTCS_BUSY_LENGTH 1 +#define DMI_ABSTRACTCS_BUSY (0x1 << DMI_ABSTRACTCS_BUSY_OFFSET) +/* +* Gets set if an abstract command fails. The bits in this field remain set until +* they are cleared by writing 1 to them. No abstract command is +* started until the value is reset to 0. +* +* 0 (none): No error. +* +* 1 (busy): An abstract command was executing while \Rcommand or one +* of the {\tt data} registers was accessed. +* +* 2 (not supported): The requested command is not supported. A +* command that is not supported while the hart is running may be +* supported when it is halted. +* +* 3 (exception): An exception occurred while executing the command +* (eg. while executing the Program Buffer). +* +* 4 (halt/resume): An abstract command couldn't execute because the +* hart wasn't in the expected state (running/halted). +* +* 7 (other): The command failed for another reason. + */ +#define DMI_ABSTRACTCS_CMDERR_OFFSET 8 +#define DMI_ABSTRACTCS_CMDERR_LENGTH 3 +#define DMI_ABSTRACTCS_CMDERR (0x7 << DMI_ABSTRACTCS_CMDERR_OFFSET) +/* +* Number of {\tt data} registers that are implemented as part of the +* abstract command interface. Valid sizes are 0 - 8. + */ +#define DMI_ABSTRACTCS_DATACOUNT_OFFSET 0 +#define DMI_ABSTRACTCS_DATACOUNT_LENGTH 5 +#define DMI_ABSTRACTCS_DATACOUNT (0x1f << DMI_ABSTRACTCS_DATACOUNT_OFFSET) +#define DMI_COMMAND 0x17 +/* +* The type determines the overall functionality of this +* abstract command. + */ +#define DMI_COMMAND_CMDTYPE_OFFSET 24 +#define DMI_COMMAND_CMDTYPE_LENGTH 8 +#define DMI_COMMAND_CMDTYPE (0xff << DMI_COMMAND_CMDTYPE_OFFSET) +/* +* This field is interpreted in a command-specific manner, +* described for each abstract command. + */ +#define DMI_COMMAND_CONTROL_OFFSET 0 +#define DMI_COMMAND_CONTROL_LENGTH 24 +#define DMI_COMMAND_CONTROL (0xffffff << DMI_COMMAND_CONTROL_OFFSET) +#define DMI_ABSTRACTAUTO 0x18 +/* +* When a bit in this field is 1, read or write accesses the corresponding {\tt progbuf} word +* cause the command in \Rcommand to be executed again. + */ +#define DMI_ABSTRACTAUTO_AUTOEXECPROGBUF_OFFSET 16 +#define DMI_ABSTRACTAUTO_AUTOEXECPROGBUF_LENGTH 16 +#define DMI_ABSTRACTAUTO_AUTOEXECPROGBUF (0xffff << DMI_ABSTRACTAUTO_AUTOEXECPROGBUF_OFFSET) +/* +* When a bit in this field is 1, read or write accesses the corresponding {\tt data} word +* cause the command in \Rcommand to be executed again. + */ +#define DMI_ABSTRACTAUTO_AUTOEXECDATA_OFFSET 0 +#define DMI_ABSTRACTAUTO_AUTOEXECDATA_LENGTH 12 +#define DMI_ABSTRACTAUTO_AUTOEXECDATA (0xfff << DMI_ABSTRACTAUTO_AUTOEXECDATA_OFFSET) +#define DMI_CFGSTRADDR0 0x19 +#define DMI_CFGSTRADDR0_ADDR_OFFSET 0 +#define DMI_CFGSTRADDR0_ADDR_LENGTH 32 +#define DMI_CFGSTRADDR0_ADDR (0xffffffff << DMI_CFGSTRADDR0_ADDR_OFFSET) +#define DMI_CFGSTRADDR1 0x1a +#define DMI_CFGSTRADDR2 0x1b +#define DMI_CFGSTRADDR3 0x1c +#define DMI_DATA0 0x04 +#define DMI_DATA0_DATA_OFFSET 0 +#define DMI_DATA0_DATA_LENGTH 32 +#define DMI_DATA0_DATA (0xffffffff << DMI_DATA0_DATA_OFFSET) +#define DMI_DATA1 0x05 +#define DMI_DATA2 0x06 +#define DMI_DATA3 0x07 +#define DMI_DATA4 0x08 +#define DMI_DATA5 0x09 +#define DMI_DATA6 0x0a +#define DMI_DATA7 0x0b +#define DMI_DATA8 0x0c +#define DMI_DATA9 0x0d +#define DMI_DATA10 0x0e +#define DMI_DATA11 0x0f +#define DMI_PROGBUF0 0x20 +#define DMI_PROGBUF0_DATA_OFFSET 0 +#define DMI_PROGBUF0_DATA_LENGTH 32 +#define DMI_PROGBUF0_DATA (0xffffffff << DMI_PROGBUF0_DATA_OFFSET) +#define DMI_PROGBUF1 0x21 +#define DMI_PROGBUF2 0x22 +#define DMI_PROGBUF3 0x23 +#define DMI_PROGBUF4 0x24 +#define DMI_PROGBUF5 0x25 +#define DMI_PROGBUF6 0x26 +#define DMI_PROGBUF7 0x27 +#define DMI_PROGBUF8 0x28 +#define DMI_PROGBUF9 0x29 +#define DMI_PROGBUF10 0x2a +#define DMI_AUTHDATA 0x30 +#define DMI_AUTHDATA_DATA_OFFSET 0 +#define DMI_AUTHDATA_DATA_LENGTH 32 +#define DMI_AUTHDATA_DATA (0xffffffff << DMI_AUTHDATA_DATA_OFFSET) +#define DMI_SERCS 0x34 +/* +* Number of supported serial ports. + */ +#define DMI_SERCS_SERIALCOUNT_OFFSET 28 +#define DMI_SERCS_SERIALCOUNT_LENGTH 4 +#define DMI_SERCS_SERIALCOUNT (0xf << DMI_SERCS_SERIALCOUNT_OFFSET) +/* +* Select which serial port is accessed by \Rserrx and \Rsertx. + */ +#define DMI_SERCS_SERIAL_OFFSET 24 +#define DMI_SERCS_SERIAL_LENGTH 3 +#define DMI_SERCS_SERIAL (0x7 << DMI_SERCS_SERIAL_OFFSET) +#define DMI_SERCS_ERROR7_OFFSET 23 +#define DMI_SERCS_ERROR7_LENGTH 1 +#define DMI_SERCS_ERROR7 (0x1 << DMI_SERCS_ERROR7_OFFSET) +#define DMI_SERCS_VALID7_OFFSET 22 +#define DMI_SERCS_VALID7_LENGTH 1 +#define DMI_SERCS_VALID7 (0x1 << DMI_SERCS_VALID7_OFFSET) +#define DMI_SERCS_FULL7_OFFSET 21 +#define DMI_SERCS_FULL7_LENGTH 1 +#define DMI_SERCS_FULL7 (0x1 << DMI_SERCS_FULL7_OFFSET) +#define DMI_SERCS_ERROR6_OFFSET 20 +#define DMI_SERCS_ERROR6_LENGTH 1 +#define DMI_SERCS_ERROR6 (0x1 << DMI_SERCS_ERROR6_OFFSET) +#define DMI_SERCS_VALID6_OFFSET 19 +#define DMI_SERCS_VALID6_LENGTH 1 +#define DMI_SERCS_VALID6 (0x1 << DMI_SERCS_VALID6_OFFSET) +#define DMI_SERCS_FULL6_OFFSET 18 +#define DMI_SERCS_FULL6_LENGTH 1 +#define DMI_SERCS_FULL6 (0x1 << DMI_SERCS_FULL6_OFFSET) +#define DMI_SERCS_ERROR5_OFFSET 17 +#define DMI_SERCS_ERROR5_LENGTH 1 +#define DMI_SERCS_ERROR5 (0x1 << DMI_SERCS_ERROR5_OFFSET) +#define DMI_SERCS_VALID5_OFFSET 16 +#define DMI_SERCS_VALID5_LENGTH 1 +#define DMI_SERCS_VALID5 (0x1 << DMI_SERCS_VALID5_OFFSET) +#define DMI_SERCS_FULL5_OFFSET 15 +#define DMI_SERCS_FULL5_LENGTH 1 +#define DMI_SERCS_FULL5 (0x1 << DMI_SERCS_FULL5_OFFSET) +#define DMI_SERCS_ERROR4_OFFSET 14 +#define DMI_SERCS_ERROR4_LENGTH 1 +#define DMI_SERCS_ERROR4 (0x1 << DMI_SERCS_ERROR4_OFFSET) +#define DMI_SERCS_VALID4_OFFSET 13 +#define DMI_SERCS_VALID4_LENGTH 1 +#define DMI_SERCS_VALID4 (0x1 << DMI_SERCS_VALID4_OFFSET) +#define DMI_SERCS_FULL4_OFFSET 12 +#define DMI_SERCS_FULL4_LENGTH 1 +#define DMI_SERCS_FULL4 (0x1 << DMI_SERCS_FULL4_OFFSET) +#define DMI_SERCS_ERROR3_OFFSET 11 +#define DMI_SERCS_ERROR3_LENGTH 1 +#define DMI_SERCS_ERROR3 (0x1 << DMI_SERCS_ERROR3_OFFSET) +#define DMI_SERCS_VALID3_OFFSET 10 +#define DMI_SERCS_VALID3_LENGTH 1 +#define DMI_SERCS_VALID3 (0x1 << DMI_SERCS_VALID3_OFFSET) +#define DMI_SERCS_FULL3_OFFSET 9 +#define DMI_SERCS_FULL3_LENGTH 1 +#define DMI_SERCS_FULL3 (0x1 << DMI_SERCS_FULL3_OFFSET) +#define DMI_SERCS_ERROR2_OFFSET 8 +#define DMI_SERCS_ERROR2_LENGTH 1 +#define DMI_SERCS_ERROR2 (0x1 << DMI_SERCS_ERROR2_OFFSET) +#define DMI_SERCS_VALID2_OFFSET 7 +#define DMI_SERCS_VALID2_LENGTH 1 +#define DMI_SERCS_VALID2 (0x1 << DMI_SERCS_VALID2_OFFSET) +#define DMI_SERCS_FULL2_OFFSET 6 +#define DMI_SERCS_FULL2_LENGTH 1 +#define DMI_SERCS_FULL2 (0x1 << DMI_SERCS_FULL2_OFFSET) +#define DMI_SERCS_ERROR1_OFFSET 5 +#define DMI_SERCS_ERROR1_LENGTH 1 +#define DMI_SERCS_ERROR1 (0x1 << DMI_SERCS_ERROR1_OFFSET) +#define DMI_SERCS_VALID1_OFFSET 4 +#define DMI_SERCS_VALID1_LENGTH 1 +#define DMI_SERCS_VALID1 (0x1 << DMI_SERCS_VALID1_OFFSET) +#define DMI_SERCS_FULL1_OFFSET 3 +#define DMI_SERCS_FULL1_LENGTH 1 +#define DMI_SERCS_FULL1 (0x1 << DMI_SERCS_FULL1_OFFSET) +/* +* 1 when the debugger-to-core queue for serial port 0 has +* over or underflowed. This bit will remain set until it is reset by +* writing 1 to this bit. + */ +#define DMI_SERCS_ERROR0_OFFSET 2 +#define DMI_SERCS_ERROR0_LENGTH 1 +#define DMI_SERCS_ERROR0 (0x1 << DMI_SERCS_ERROR0_OFFSET) +/* +* 1 when the core-to-debugger queue for serial port 0 is not empty. + */ +#define DMI_SERCS_VALID0_OFFSET 1 +#define DMI_SERCS_VALID0_LENGTH 1 +#define DMI_SERCS_VALID0 (0x1 << DMI_SERCS_VALID0_OFFSET) +/* +* 1 when the debugger-to-core queue for serial port 0 is full. + */ +#define DMI_SERCS_FULL0_OFFSET 0 +#define DMI_SERCS_FULL0_LENGTH 1 +#define DMI_SERCS_FULL0 (0x1 << DMI_SERCS_FULL0_OFFSET) +#define DMI_SERTX 0x35 +#define DMI_SERTX_DATA_OFFSET 0 +#define DMI_SERTX_DATA_LENGTH 32 +#define DMI_SERTX_DATA (0xffffffff << DMI_SERTX_DATA_OFFSET) +#define DMI_SERRX 0x36 +#define DMI_SERRX_DATA_OFFSET 0 +#define DMI_SERRX_DATA_LENGTH 32 +#define DMI_SERRX_DATA (0xffffffff << DMI_SERRX_DATA_OFFSET) +#define DMI_SBCS 0x38 /* * When a 1 is written here, triggers a read at the address in {\tt * sbaddress} using the access size set by \Fsbaccess. @@ -789,8 +1098,8 @@ * 4: 128-bit * * If an unsupported system bus access size is written here, -* the DM may not -* perform the access, or may perform the access with any access size +* the DM may not perform the access, or may perform the access +* with any access size. */ #define DMI_SBCS_SBACCESS_OFFSET 17 #define DMI_SBCS_SBACCESS_LENGTH 3 @@ -812,9 +1121,9 @@ #define DMI_SBCS_SBAUTOREAD (0x1 << DMI_SBCS_SBAUTOREAD_OFFSET) /* * When the debug module's system bus -* master causes a bus error, this field gets set. -* It remains set until 0 is written to any bit in this field. Until -* that happens, the system bus master is busy and no more accesses can be +* master causes a bus error, this field gets set. The bits in this +* field remain set until they are cleared by writing 1 to them. +* While this field is non-zero, no more system bus accesses can be * initiated by the debug module. * * 0: There was no bus error. @@ -870,14 +1179,14 @@ #define DMI_SBCS_SBACCESS8_OFFSET 0 #define DMI_SBCS_SBACCESS8_LENGTH 1 #define DMI_SBCS_SBACCESS8 (0x1 << DMI_SBCS_SBACCESS8_OFFSET) -#define DMI_SBADDRESS0 0x04 +#define DMI_SBADDRESS0 0x39 /* * Accesses bits 31:0 of the internal address. */ #define DMI_SBADDRESS0_ADDRESS_OFFSET 0 #define DMI_SBADDRESS0_ADDRESS_LENGTH 32 #define DMI_SBADDRESS0_ADDRESS (0xffffffff << DMI_SBADDRESS0_ADDRESS_OFFSET) -#define DMI_SBADDRESS1 0x05 +#define DMI_SBADDRESS1 0x3a /* * Accesses bits 63:32 of the internal address (if the system address * bus is that wide). @@ -885,7 +1194,7 @@ #define DMI_SBADDRESS1_ADDRESS_OFFSET 0 #define DMI_SBADDRESS1_ADDRESS_LENGTH 32 #define DMI_SBADDRESS1_ADDRESS (0xffffffff << DMI_SBADDRESS1_ADDRESS_OFFSET) -#define DMI_SBADDRESS2 0x06 +#define DMI_SBADDRESS2 0x3b /* * Accesses bits 95:64 of the internal address (if the system address * bus is that wide). @@ -893,14 +1202,14 @@ #define DMI_SBADDRESS2_ADDRESS_OFFSET 0 #define DMI_SBADDRESS2_ADDRESS_LENGTH 32 #define DMI_SBADDRESS2_ADDRESS (0xffffffff << DMI_SBADDRESS2_ADDRESS_OFFSET) -#define DMI_SBDATA0 0x07 +#define DMI_SBDATA0 0x3c /* * Accesses bits 31:0 of the internal data. */ #define DMI_SBDATA0_DATA_OFFSET 0 #define DMI_SBDATA0_DATA_LENGTH 32 #define DMI_SBDATA0_DATA (0xffffffff << DMI_SBDATA0_DATA_OFFSET) -#define DMI_SBDATA1 0x08 +#define DMI_SBDATA1 0x3d /* * Accesses bits 63:32 of the internal data (if the system bus is * that wide). @@ -908,7 +1217,7 @@ #define DMI_SBDATA1_DATA_OFFSET 0 #define DMI_SBDATA1_DATA_LENGTH 32 #define DMI_SBDATA1_DATA (0xffffffff << DMI_SBDATA1_DATA_OFFSET) -#define DMI_SBDATA2 0x09 +#define DMI_SBDATA2 0x3e /* * Accesses bits 95:64 of the internal data (if the system bus is * that wide). @@ -916,7 +1225,7 @@ #define DMI_SBDATA2_DATA_OFFSET 0 #define DMI_SBDATA2_DATA_LENGTH 32 #define DMI_SBDATA2_DATA (0xffffffff << DMI_SBDATA2_DATA_OFFSET) -#define DMI_SBDATA3 0x0a +#define DMI_SBDATA3 0x3f /* * Accesses bits 127:96 of the internal data (if the system bus is * that wide). @@ -924,215 +1233,7 @@ #define DMI_SBDATA3_DATA_OFFSET 0 #define DMI_SBDATA3_DATA_LENGTH 32 #define DMI_SBDATA3_DATA (0xffffffff << DMI_SBDATA3_DATA_OFFSET) -#define DMI_AUTHDATA 0x0b -#define DMI_AUTHDATA_DATA_OFFSET 0 -#define DMI_AUTHDATA_DATA_LENGTH 32 -#define DMI_AUTHDATA_DATA (0xffffffff << DMI_AUTHDATA_DATA_OFFSET) -#define DMI_ABSTRACTCS 0x0e -#define DMI_ABSTRACTCS_AUTOEXEC7_OFFSET 15 -#define DMI_ABSTRACTCS_AUTOEXEC7_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC7 (0x1 << DMI_ABSTRACTCS_AUTOEXEC7_OFFSET) -#define DMI_ABSTRACTCS_AUTOEXEC6_OFFSET 14 -#define DMI_ABSTRACTCS_AUTOEXEC6_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC6 (0x1 << DMI_ABSTRACTCS_AUTOEXEC6_OFFSET) -#define DMI_ABSTRACTCS_AUTOEXEC5_OFFSET 13 -#define DMI_ABSTRACTCS_AUTOEXEC5_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC5 (0x1 << DMI_ABSTRACTCS_AUTOEXEC5_OFFSET) -#define DMI_ABSTRACTCS_AUTOEXEC4_OFFSET 12 -#define DMI_ABSTRACTCS_AUTOEXEC4_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC4 (0x1 << DMI_ABSTRACTCS_AUTOEXEC4_OFFSET) -#define DMI_ABSTRACTCS_AUTOEXEC3_OFFSET 11 -#define DMI_ABSTRACTCS_AUTOEXEC3_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC3 (0x1 << DMI_ABSTRACTCS_AUTOEXEC3_OFFSET) -#define DMI_ABSTRACTCS_AUTOEXEC2_OFFSET 10 -#define DMI_ABSTRACTCS_AUTOEXEC2_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC2 (0x1 << DMI_ABSTRACTCS_AUTOEXEC2_OFFSET) -#define DMI_ABSTRACTCS_AUTOEXEC1_OFFSET 9 -#define DMI_ABSTRACTCS_AUTOEXEC1_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC1 (0x1 << DMI_ABSTRACTCS_AUTOEXEC1_OFFSET) -/* -* When 1, accesses to \Rdatazero cause the command in \Rcommand to be -* executed again. -* -* The same is true for other other autoexec bits: When 1, accesses to -* {\tt data}N cause the command in \Rcommand to be executed again. - */ -#define DMI_ABSTRACTCS_AUTOEXEC0_OFFSET 8 -#define DMI_ABSTRACTCS_AUTOEXEC0_LENGTH 1 -#define DMI_ABSTRACTCS_AUTOEXEC0 (0x1 << DMI_ABSTRACTCS_AUTOEXEC0_OFFSET) -/* -* Gets set if an abstract command fails. No abstract command is -* started until the value is reset to 0. -* -* 0 (none): No error. -* -* 1 (busy): An abstract command was executing while \Rcommand or one -* of the {\tt data} registers was accessed. -* -* 2 (not supported): The requested command is not supported. A -* command that is not supported while the hart is running may be -* supported when it is halted. -* -* 3 (exception): An exception occurred while executing the command -* (eg. while executing the Program Buffer). -* -* 4 (halt/resume): An abstract command couldn't execute because the -* hart wasn't in the expected state (running/halted). -* -* 7 (other): The command failed for another reason. - */ -#define DMI_ABSTRACTCS_CMDERR_OFFSET 5 -#define DMI_ABSTRACTCS_CMDERR_LENGTH 3 -#define DMI_ABSTRACTCS_CMDERR (0x7 << DMI_ABSTRACTCS_CMDERR_OFFSET) -/* -* 1: An abstract command is currently being executed. -* -* This bit is set as soon as \Rcommand is written, and isn't cleared -* until that command has completed. - */ -#define DMI_ABSTRACTCS_BUSY_OFFSET 4 -#define DMI_ABSTRACTCS_BUSY_LENGTH 1 -#define DMI_ABSTRACTCS_BUSY (0x1 << DMI_ABSTRACTCS_BUSY_OFFSET) -/* -* Number of {\tt data} registers that are implemented as part of the -* abstract command interface. If it's 0 then no abstract interface is -* implemented at all. - */ -#define DMI_ABSTRACTCS_DATACOUNT_OFFSET 0 -#define DMI_ABSTRACTCS_DATACOUNT_LENGTH 4 -#define DMI_ABSTRACTCS_DATACOUNT (0xf << DMI_ABSTRACTCS_DATACOUNT_OFFSET) -#define DMI_COMMAND 0x0f -/* -* The type determines the overall functionality of this -* abstract command. - */ -#define DMI_COMMAND_TYPE_OFFSET 24 -#define DMI_COMMAND_TYPE_LENGTH 8 -#define DMI_COMMAND_TYPE (0xff << DMI_COMMAND_TYPE_OFFSET) -/* -* This field is interpreted in a command-specific manner, -* described for each abstract command. - */ -#define DMI_COMMAND_CONTROL_OFFSET 0 -#define DMI_COMMAND_CONTROL_LENGTH 24 -#define DMI_COMMAND_CONTROL (0xffffff << DMI_COMMAND_CONTROL_OFFSET) -#define DMI_DATA0 0x10 -#define DMI_DATA0_DATA_OFFSET 0 -#define DMI_DATA0_DATA_LENGTH 32 -#define DMI_DATA0_DATA (0xffffffff << DMI_DATA0_DATA_OFFSET) -#define DMI_DATA1 0x11 -#define DMI_DATA2 0x12 -#define DMI_DATA3 0x13 -#define DMI_DATA4 0x14 -#define DMI_DATA5 0x15 -#define DMI_DATA6 0x16 -#define DMI_DATA7 0x17 -#define DMI_DATA8 0x18 -#define DMI_DATA9 0x19 -#define DMI_DATA10 0x1a -#define DMI_DATA11 0x1b -#define DMI_SERDATA 0x1c -#define DMI_SERDATA_DATA_OFFSET 0 -#define DMI_SERDATA_DATA_LENGTH 32 -#define DMI_SERDATA_DATA (0xffffffff << DMI_SERDATA_DATA_OFFSET) -#define DMI_SERCS 0x1d -/* -* Number of supported serial ports. - */ -#define DMI_SERCS_SERIALCOUNT_OFFSET 28 -#define DMI_SERCS_SERIALCOUNT_LENGTH 4 -#define DMI_SERCS_SERIALCOUNT (0xf << DMI_SERCS_SERIALCOUNT_OFFSET) -/* -* Select which serial port is accessed by \Rserdata. - */ -#define DMI_SERCS_SERIAL_OFFSET 16 -#define DMI_SERCS_SERIAL_LENGTH 3 -#define DMI_SERCS_SERIAL (0x7 << DMI_SERCS_SERIAL_OFFSET) -#define DMI_SERCS_VALID7_OFFSET 15 -#define DMI_SERCS_VALID7_LENGTH 1 -#define DMI_SERCS_VALID7 (0x1 << DMI_SERCS_VALID7_OFFSET) -#define DMI_SERCS_FULL_OVERFLOW7_OFFSET 14 -#define DMI_SERCS_FULL_OVERFLOW7_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW7 (0x1 << DMI_SERCS_FULL_OVERFLOW7_OFFSET) -#define DMI_SERCS_VALID6_OFFSET 13 -#define DMI_SERCS_VALID6_LENGTH 1 -#define DMI_SERCS_VALID6 (0x1 << DMI_SERCS_VALID6_OFFSET) -#define DMI_SERCS_FULL_OVERFLOW6_OFFSET 12 -#define DMI_SERCS_FULL_OVERFLOW6_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW6 (0x1 << DMI_SERCS_FULL_OVERFLOW6_OFFSET) -#define DMI_SERCS_VALID5_OFFSET 11 -#define DMI_SERCS_VALID5_LENGTH 1 -#define DMI_SERCS_VALID5 (0x1 << DMI_SERCS_VALID5_OFFSET) -#define DMI_SERCS_FULL_OVERFLOW5_OFFSET 10 -#define DMI_SERCS_FULL_OVERFLOW5_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW5 (0x1 << DMI_SERCS_FULL_OVERFLOW5_OFFSET) -#define DMI_SERCS_VALID4_OFFSET 9 -#define DMI_SERCS_VALID4_LENGTH 1 -#define DMI_SERCS_VALID4 (0x1 << DMI_SERCS_VALID4_OFFSET) -#define DMI_SERCS_FULL_OVERFLOW4_OFFSET 8 -#define DMI_SERCS_FULL_OVERFLOW4_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW4 (0x1 << DMI_SERCS_FULL_OVERFLOW4_OFFSET) -#define DMI_SERCS_VALID3_OFFSET 7 -#define DMI_SERCS_VALID3_LENGTH 1 -#define DMI_SERCS_VALID3 (0x1 << DMI_SERCS_VALID3_OFFSET) -#define DMI_SERCS_FULL_OVERFLOW3_OFFSET 6 -#define DMI_SERCS_FULL_OVERFLOW3_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW3 (0x1 << DMI_SERCS_FULL_OVERFLOW3_OFFSET) -#define DMI_SERCS_VALID2_OFFSET 5 -#define DMI_SERCS_VALID2_LENGTH 1 -#define DMI_SERCS_VALID2 (0x1 << DMI_SERCS_VALID2_OFFSET) -#define DMI_SERCS_FULL_OVERFLOW2_OFFSET 4 -#define DMI_SERCS_FULL_OVERFLOW2_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW2 (0x1 << DMI_SERCS_FULL_OVERFLOW2_OFFSET) -#define DMI_SERCS_VALID1_OFFSET 3 -#define DMI_SERCS_VALID1_LENGTH 1 -#define DMI_SERCS_VALID1 (0x1 << DMI_SERCS_VALID1_OFFSET) -#define DMI_SERCS_FULL_OVERFLOW1_OFFSET 2 -#define DMI_SERCS_FULL_OVERFLOW1_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW1 (0x1 << DMI_SERCS_FULL_OVERFLOW1_OFFSET) -/* -* 1 when the core-to-debugger queue for serial port 0 is not empty. - */ -#define DMI_SERCS_VALID0_OFFSET 1 -#define DMI_SERCS_VALID0_LENGTH 1 -#define DMI_SERCS_VALID0 (0x1 << DMI_SERCS_VALID0_OFFSET) -/* -* 1 when the debugger-to-core queue for serial port 0 is either full, -* or has overflowed. Overflow state is sticky, and can be reset by -* writing 0 to this bit. - */ -#define DMI_SERCS_FULL_OVERFLOW0_OFFSET 0 -#define DMI_SERCS_FULL_OVERFLOW0_LENGTH 1 -#define DMI_SERCS_FULL_OVERFLOW0 (0x1 << DMI_SERCS_FULL_OVERFLOW0_OFFSET) -#define DMI_PROGBUFCS 0x1f -/* -* Size of the Program Buffer, in 32-bit words. Valid sizes are 0 - 12. -* -* A debugger must not access any Program Buffer locations that -* fall outside the range specified here. -* -* TODO: Explain what can be done with each size of the buffer, to suggest -* why you would want more or less words. - */ -#define DMI_PROGBUFCS_PROGSIZE_OFFSET 0 -#define DMI_PROGBUFCS_PROGSIZE_LENGTH 4 -#define DMI_PROGBUFCS_PROGSIZE (0xf << DMI_PROGBUFCS_PROGSIZE_OFFSET) -#define DMI_PROGBUF0 0x20 -#define DMI_PROGBUF0_DATA_OFFSET 0 -#define DMI_PROGBUF0_DATA_LENGTH 32 -#define DMI_PROGBUF0_DATA (0xffffffff << DMI_PROGBUF0_DATA_OFFSET) -#define DMI_PROGBUF1 0x21 -#define DMI_PROGBUF2 0x22 -#define DMI_PROGBUF3 0x23 -#define DMI_PROGBUF4 0x24 -#define DMI_PROGBUF5 0x25 -#define DMI_PROGBUF6 0x26 -#define DMI_PROGBUF7 0x27 -#define DMI_PROGBUF8 0x28 -#define DMI_PROGBUF9 0x29 -#define DMI_PROGBUF10 0x2a -#define DMI_PROGBUF11 0x2b -#define SERINFO 0x110 +#define SERINFO 0x280 /* * Like \Fserialzero. */ @@ -1198,27 +1299,27 @@ #define SERSTAT0_RECVR_OFFSET 0 #define SERSTAT0_RECVR_LENGTH 1 #define SERSTAT0_RECVR (0x1 << SERSTAT0_RECVR_OFFSET) -#define SERSEND1 0x20c -#define SERRECV1 0x210 -#define SERSTAT1 0x214 -#define SERSEND2 0x218 -#define SERRECV2 0x21c -#define SERSTAT2 0x220 -#define SERSEND3 0x224 -#define SERRECV3 0x228 -#define SERSTAT3 0x22c -#define SERSEND4 0x230 -#define SERRECV4 0x234 -#define SERSTAT4 0x238 -#define SERSEND5 0x23c -#define SERRECV5 0x240 -#define SERSTAT5 0x244 -#define SERSEND6 0x248 -#define SERRECV6 0x24c -#define SERSTAT6 0x250 -#define SERSEND7 0x254 -#define SERRECV7 0x258 -#define SERSTAT7 0x25c +#define SERSEND1 0x210 +#define SERRECV1 0x214 +#define SERSTAT1 0x218 +#define SERSEND2 0x220 +#define SERRECV2 0x224 +#define SERSTAT2 0x228 +#define SERSEND3 0x230 +#define SERRECV3 0x234 +#define SERSTAT3 0x238 +#define SERSEND4 0x240 +#define SERRECV4 0x244 +#define SERSTAT4 0x248 +#define SERSEND5 0x250 +#define SERRECV5 0x254 +#define SERSTAT5 0x258 +#define SERSEND6 0x260 +#define SERRECV6 0x264 +#define SERSTAT6 0x268 +#define SERSEND7 0x274 +#define SERRECV7 0x278 +#define SERSTAT7 0x27c #define TRACE 0x728 /* * 1 if the trace buffer has wrapped since the last time \Fdiscard was @@ -1334,9 +1435,9 @@ /* * This is 0 to indicate Access Register Command. */ -#define AC_ACCESS_REGISTER_TYPE_OFFSET 24 -#define AC_ACCESS_REGISTER_TYPE_LENGTH 8 -#define AC_ACCESS_REGISTER_TYPE (0xff << AC_ACCESS_REGISTER_TYPE_OFFSET) +#define AC_ACCESS_REGISTER_CMDTYPE_OFFSET 24 +#define AC_ACCESS_REGISTER_CMDTYPE_LENGTH 8 +#define AC_ACCESS_REGISTER_CMDTYPE (0xff << AC_ACCESS_REGISTER_CMDTYPE_OFFSET) /* * 2: Access the lowest 32 bits of the register. * @@ -1344,28 +1445,38 @@ * * 4: Access the lowest 128 bits of the register. * -* If \Fsize specifies a size larger than the register is, then the -* access must fail. If a register is accessible, then \Fsize matching -* the register's actual size must be supported. +* If \Fsize specifies a size larger than the register's actual size, +* then the access must fail. If a register is accessible, then reads of \Fsize +* less than or equal to the register's actual size must be supported. */ -#define AC_ACCESS_REGISTER_SIZE_OFFSET 19 +#define AC_ACCESS_REGISTER_SIZE_OFFSET 20 #define AC_ACCESS_REGISTER_SIZE_LENGTH 3 #define AC_ACCESS_REGISTER_SIZE (0x7 << AC_ACCESS_REGISTER_SIZE_OFFSET) /* * When 1, execute the program in the Program Buffer exactly once -* before performing the read/write. +* before performing the transfer. +* \textbf{WARNING: preexec is considered for removal.} */ -#define AC_ACCESS_REGISTER_PREEXEC_OFFSET 18 +#define AC_ACCESS_REGISTER_PREEXEC_OFFSET 19 #define AC_ACCESS_REGISTER_PREEXEC_LENGTH 1 #define AC_ACCESS_REGISTER_PREEXEC (0x1 << AC_ACCESS_REGISTER_PREEXEC_OFFSET) /* * When 1, execute the program in the Program Buffer exactly once -* after performing the read/write. +* after performing the transfer, if any. */ -#define AC_ACCESS_REGISTER_POSTEXEC_OFFSET 17 +#define AC_ACCESS_REGISTER_POSTEXEC_OFFSET 18 #define AC_ACCESS_REGISTER_POSTEXEC_LENGTH 1 #define AC_ACCESS_REGISTER_POSTEXEC (0x1 << AC_ACCESS_REGISTER_POSTEXEC_OFFSET) /* +* 0: Don't do the operation specified by \Fwrite. +* +* 1: Do the operation specified by \Fwrite. + */ +#define AC_ACCESS_REGISTER_TRANSFER_OFFSET 17 +#define AC_ACCESS_REGISTER_TRANSFER_LENGTH 1 +#define AC_ACCESS_REGISTER_TRANSFER (0x1 << AC_ACCESS_REGISTER_TRANSFER_OFFSET) +/* +* When \Ftransfer is set: * 0: Copy data from the specified register into {\tt arg0} portion * of {\tt data}. * @@ -1385,6 +1496,6 @@ /* * This is 1 to indicate Quick Access command. */ -#define AC_QUICK_ACCESS_TYPE_OFFSET 24 -#define AC_QUICK_ACCESS_TYPE_LENGTH 8 -#define AC_QUICK_ACCESS_TYPE (0xff << AC_QUICK_ACCESS_TYPE_OFFSET) +#define AC_QUICK_ACCESS_CMDTYPE_OFFSET 24 +#define AC_QUICK_ACCESS_CMDTYPE_LENGTH 8 +#define AC_QUICK_ACCESS_CMDTYPE (0xff << AC_QUICK_ACCESS_CMDTYPE_OFFSET) diff --git a/src/target/riscv/riscv-013.c b/src/target/riscv/riscv-013.c index 6aac4fd..f12a29f 100644 --- a/src/target/riscv/riscv-013.c +++ b/src/target/riscv/riscv-013.c @@ -367,7 +367,7 @@ static uint32_t dtmcontrol_scan(struct target *target, uint32_t out) } uint32_t in = buf_get_u32(field.in_value, 0, 32); - LOG_DEBUG("DTMCONTROL: 0x%x -> 0x%x", out, in); + LOG_DEBUG("DTMCS: 0x%x -> 0x%x", out, in); return in; } @@ -389,7 +389,7 @@ static void increase_dmi_busy_delay(struct target *target) info->dtmcontrol_idle, info->dmi_busy_delay, info->ac_busy_delay); - dtmcontrol_scan(target, DTM_DTMCONTROL_DMIRESET); + dtmcontrol_scan(target, DTM_DTMCS_DMIRESET); } /** @@ -1462,29 +1462,30 @@ static int examine(struct target *target) uint32_t dtmcontrol = dtmcontrol_scan(target, 0); LOG_DEBUG("dtmcontrol=0x%x", dtmcontrol); - LOG_DEBUG(" dmireset=%d", get_field(dtmcontrol, DTM_DTMCONTROL_DMIRESET)); - LOG_DEBUG(" idle=%d", get_field(dtmcontrol, DTM_DTMCONTROL_IDLE)); - LOG_DEBUG(" dmistat=%d", get_field(dtmcontrol, DTM_DTMCONTROL_DMISTAT)); - LOG_DEBUG(" abits=%d", get_field(dtmcontrol, DTM_DTMCONTROL_ABITS)); - LOG_DEBUG(" version=%d", get_field(dtmcontrol, DTM_DTMCONTROL_VERSION)); + LOG_DEBUG(" dmireset=%d", get_field(dtmcontrol, DTM_DTMCS_DMIRESET)); + LOG_DEBUG(" idle=%d", get_field(dtmcontrol, DTM_DTMCS_IDLE)); + LOG_DEBUG(" dmistat=%d", get_field(dtmcontrol, DTM_DTMCS_DMISTAT)); + LOG_DEBUG(" abits=%d", get_field(dtmcontrol, DTM_DTMCS_ABITS)); + LOG_DEBUG(" version=%d", get_field(dtmcontrol, DTM_DTMCS_VERSION)); if (dtmcontrol == 0) { LOG_ERROR("dtmcontrol is 0. Check JTAG connectivity/board power."); return ERROR_FAIL; } - if (get_field(dtmcontrol, DTM_DTMCONTROL_VERSION) != 1) { + if (get_field(dtmcontrol, DTM_DTMCS_VERSION) != 1) { LOG_ERROR("Unsupported DTM version %d. (dtmcontrol=0x%x)", - get_field(dtmcontrol, DTM_DTMCONTROL_VERSION), dtmcontrol); + get_field(dtmcontrol, DTM_DTMCS_VERSION), dtmcontrol); return ERROR_FAIL; } riscv013_info_t *info = get_info(target); - info->abits = get_field(dtmcontrol, DTM_DTMCONTROL_ABITS); - info->dtmcontrol_idle = get_field(dtmcontrol, DTM_DTMCONTROL_IDLE); + info->abits = get_field(dtmcontrol, DTM_DTMCS_ABITS); + info->dtmcontrol_idle = get_field(dtmcontrol, DTM_DTMCS_IDLE); uint32_t dmcontrol = dmi_read(target, DMI_DMCONTROL); - if (get_field(dmcontrol, DMI_DMCONTROL_VERSION) != 1) { - LOG_ERROR("OpenOCD only supports Debug Module version 1, not %d " - "(dmcontrol=0x%x)", get_field(dmcontrol, DMI_DMCONTROL_VERSION), dmcontrol); + uint32_t dmstatus = dmi_read(target, DMI_DMSTATUS); + if (get_field(dmstatus, DMI_DMSTATUS_VERSIONLO) != 2) { + LOG_ERROR("OpenOCD only supports Debug Module version 2, not %d " + "(dmstatus=0x%x)", get_field(dmstatus, DMI_DMSTATUS_VERSIONLO), dmstatus); return ERROR_FAIL; } @@ -1494,18 +1495,7 @@ static int examine(struct target *target) dmcontrol = dmi_read(target, DMI_DMCONTROL); LOG_DEBUG("dmcontrol: 0x%08x", dmcontrol); - LOG_DEBUG(" haltreq=%d", get_field(dmcontrol, DMI_DMCONTROL_HALTREQ)); - LOG_DEBUG(" resumereq=%d", get_field(dmcontrol, DMI_DMCONTROL_RESUMEREQ)); - LOG_DEBUG(" hartstatus=%d", get_field(dmcontrol, DMI_DMCONTROL_HARTSTATUS)); - LOG_DEBUG(" hartsel=0x%x", get_field(dmcontrol, DMI_DMCONTROL_HARTSEL)); - LOG_DEBUG(" hartreset=0x%x", get_field(dmcontrol, DMI_DMCONTROL_HARTRESET)); - LOG_DEBUG(" dmactive=%d", get_field(dmcontrol, DMI_DMCONTROL_DMACTIVE)); - LOG_DEBUG(" reset=%d", get_field(dmcontrol, DMI_DMCONTROL_RESET)); - LOG_DEBUG(" authenticated=%d", get_field(dmcontrol, DMI_DMCONTROL_AUTHENTICATED)); - LOG_DEBUG(" authbusy=%d", get_field(dmcontrol, DMI_DMCONTROL_AUTHBUSY)); - LOG_DEBUG(" version=%d", get_field(dmcontrol, DMI_DMCONTROL_VERSION)); - - unsigned hartstatus = get_field(dmcontrol, DMI_DMCONTROL_HARTSTATUS); + LOG_DEBUG("dmstatus: 0x%08x", dmstatus); if (!get_field(dmcontrol, DMI_DMCONTROL_DMACTIVE)) { LOG_ERROR("Debug Module did not become active. dmcontrol=0x%x", @@ -1513,32 +1503,27 @@ static int examine(struct target *target) return ERROR_FAIL; } - if (!get_field(dmcontrol, DMI_DMCONTROL_AUTHENTICATED)) { + if (!get_field(dmstatus, DMI_DMSTATUS_AUTHENTICATED)) { LOG_ERROR("Authentication required by RISC-V core but not " "supported by OpenOCD. dmcontrol=0x%x", dmcontrol); return ERROR_FAIL; } - if (hartstatus == 2) { + if (get_field(dmstatus, DMI_DMSTATUS_ANYUNAVAIL)) { LOG_ERROR("The hart is unavailable."); return ERROR_FAIL; } - if (hartstatus == 3) { + if (get_field(dmstatus, DMI_DMSTATUS_ANYNONEXISTENT)) { LOG_ERROR("The hart doesn't exist."); return ERROR_FAIL; } // Check that abstract data registers are accessible. uint32_t abstractcs = dmi_read(target, DMI_ABSTRACTCS); - info->datacount = get_field(abstractcs, DMI_ABSTRACTCS_DATACOUNT); LOG_DEBUG("abstractcs=0x%x", abstractcs); - LOG_DEBUG(" datacount=%d", info->datacount); - - uint32_t accesscs = dmi_read(target, DMI_PROGBUFCS); - info->progsize = get_field(accesscs, DMI_PROGBUFCS_PROGSIZE); - LOG_DEBUG("accesscs=0x%x", accesscs); - LOG_DEBUG(" progsize=%d", info->progsize); + info->datacount = get_field(abstractcs, DMI_ABSTRACTCS_DATACOUNT); + info->progsize = get_field(abstractcs, DMI_ABSTRACTCS_PROGSIZE); uint32_t value = 0x53467665; for (unsigned i = 0; i < info->datacount; i++) { @@ -1571,17 +1556,20 @@ static int examine(struct target *target) value += 0x52534335; } - if (hartstatus == 1) { + bool should_attempt_resume = false; + if (get_field(dmstatus, DMI_DMSTATUS_ANYRUNNING)) { + should_attempt_resume = true; LOG_DEBUG("Hart currently running. Requesting halt.\n"); dmi_write(target, DMI_DMCONTROL, DMI_DMCONTROL_HALTREQ | DMI_DMCONTROL_DMACTIVE); for (unsigned i = 0; i < 256; i++) { dmcontrol = dmi_read(target, DMI_DMCONTROL); - if (get_field(dmcontrol, DMI_DMCONTROL_HARTSTATUS) == 0) + dmstatus = dmi_read(target, DMI_DMSTATUS); + if (get_field(dmstatus, DMI_DMSTATUS_ALLHALTED)) break; } - if (get_field(dmcontrol, DMI_DMCONTROL_HARTSTATUS) != 0) { - LOG_ERROR("hart didn't halt; dmcontrol=0x%x", dmcontrol); + if (!get_field(dmstatus, DMI_DMSTATUS_ALLHALTED)) { + LOG_ERROR("hart didn't halt; dmstatus=0x%x", dmstatus); return ERROR_FAIL; } } @@ -1610,18 +1598,19 @@ static int examine(struct target *target) return ERROR_FAIL; } - if (hartstatus == 1) { + if (should_attempt_resume) { LOG_DEBUG("Resuming hart.\n"); // Resume if the hart had been running. dmi_write(target, DMI_DMCONTROL, DMI_DMCONTROL_DMACTIVE | DMI_DMCONTROL_RESUMEREQ); for (unsigned i = 0; i < 256; i++) { dmcontrol = dmi_read(target, DMI_DMCONTROL); - if (get_field(dmcontrol, DMI_DMCONTROL_HARTSTATUS) == 1) + dmstatus = dmi_read(target, DMI_DMSTATUS); + if (get_field(dmstatus, DMI_DMSTATUS_ALLRUNNING)) break; } - if (get_field(dmcontrol, DMI_DMCONTROL_HARTSTATUS) != 1) { - LOG_ERROR("hart didn't resume; dmcontrol=0x%x", dmcontrol); + if (!get_field(dmstatus, DMI_DMSTATUS_ALLRUNNING)) { + LOG_ERROR("hart didn't resume; dmstatus=0x%x", dmstatus); return ERROR_FAIL; } } @@ -1767,25 +1756,29 @@ static int poll_target(struct target *target, bool announce) if (debug_level >= LOG_LVL_DEBUG) { debug_level = LOG_LVL_INFO; } - uint32_t dmcontrol = dmi_read(target, DMI_DMCONTROL); debug_level = old_debug_level; - switch (get_field(dmcontrol, DMI_DMCONTROL_HARTSTATUS)) { - case 0: - if (target->state != TARGET_HALTED) { - return handle_halt(target, announce); - } - break; - case 1: - target->state = TARGET_RUNNING; - break; - case 2: - // Could be unavailable for other reasons. - target->state = TARGET_RESET; - break; - case 3: - LOG_ERROR("Hart disappeared!"); - return ERROR_FAIL; + uint32_t dmstatus = dmi_read(target, DMI_DMSTATUS); + if (get_field(dmstatus, DMI_DMSTATUS_ALLHALTED)) { + if (target->state != TARGET_HALTED) { + return handle_halt(target, announce); + } + return ERROR_OK; + } + + if (get_field(dmstatus, DMI_DMSTATUS_ALLRUNNING)) { + target->state = TARGET_RUNNING; + return ERROR_OK; + } + + if (get_field(dmstatus, DMI_DMSTATUS_ANYUNAVAIL)) { + target->state = TARGET_RESET; + return ERROR_OK; + } + + if (get_field(dmstatus, DMI_DMSTATUS_ANYNONEXISTENT)) { + LOG_ERROR("Hart disappeared!"); + return ERROR_FAIL; } return ERROR_OK; @@ -1864,8 +1857,9 @@ static int read_memory(struct target *target, uint32_t address, abstract_register_size(xlen(target)) | reg_number_to_no(S1)) != ERROR_OK) { return ERROR_FAIL; } - dmi_write(target, DMI_ABSTRACTCS, DMI_ABSTRACTCS_AUTOEXEC0 | DMI_ABSTRACTCS_CMDERR); - uint32_t abstractcs; + dmi_write(target, DMI_ABSTRACTCS, DMI_ABSTRACTCS_CMDERR); + dmi_write(target, DMI_ABSTRACTAUTO, 0x1 << DMI_ABSTRACTAUTO_AUTOEXECPROGBUF_OFFSET); + for (uint32_t i = 0; i < count; i++) { uint32_t value = dmi_read(target, DMI_DATA0); switch (size) { @@ -1913,7 +1907,7 @@ static int check_dmi_error(struct target *target) false); if (status != DMI_STATUS_SUCCESS) { // Clear errors. - dtmcontrol_scan(target, DTM_DTMCONTROL_DMIRESET); + dtmcontrol_scan(target, DTM_DTMCS_DMIRESET); increase_dmi_busy_delay(target); return 1; } @@ -1975,7 +1969,10 @@ static int write_memory(struct target *target, uint32_t address, | abstract_register_size(xlen(target)) | reg_number_to_no(S1), true); scans_add_dmi_write(scans, DMI_ABSTRACTCS, - DMI_ABSTRACTCS_AUTOEXEC0 | DMI_ABSTRACTCS_CMDERR, + DMI_ABSTRACTCS_CMDERR, + false); + scans_add_dmi_write(scans, DMI_ABSTRACTAUTO, + 0x1 << DMI_ABSTRACTAUTO_AUTOEXECPROGBUF_OFFSET, false); } } |