finish removing deprecated/obsolete commands

It's been about a year since these were deprecated and, in most
cases, removed.  There's no point in carrying that documentation,
or backwards compatibility for "jtag_device" and "jtag_speed",
around forever.  (Or a few remnants of obsolete code...)

Removed a few obsolete uses of "jtag_speed":

 - The Calao stuff hasn't worked since July 2008.  (Those Atmel
   targets need to work with a 32KHz core clock after reset until
   board-specific init-reset code sets up the PLL and enables a
   faster JTAg clock.)
 - Parport speed controls don't actually work (tops out at about
   1 MHz on typical HW).
 - In general, speed controls need to live in board.cfg files (or
   sometimes target.cfg files), not interface.cfg ...

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

1 files changed, 0 insertions, 86 deletions

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 8e1d1a8..86f5748 100644
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -81,7 +81,6 @@ Free Documentation License''.
 * TFTP::                             TFTP
 * GDB and OpenOCD::                  Using GDB and OpenOCD
 * Tcl Scripting API::                Tcl Scripting API
-* Upgrading::                        Deprecated/Removed Commands
 * FAQ::                              Frequently Asked Questions
 * Tcl Crash Course::                 Tcl Crash Course
 * License::                          GNU Free Documentation License
@@ -6507,91 +6506,6 @@ We should add support for a variable like Tcl variable
 is jim, not real tcl).
 @end quotation
 
-@node Upgrading
-@chapter Deprecated/Removed Commands
-@cindex Deprecated/Removed Commands
-Certain OpenOCD commands have been deprecated or
-removed during the various revisions.
-
-Upgrade your scripts as soon as possible.
-These descriptions for old commands may be removed
-a year after the command itself was removed.
-This means that in January 2010 this chapter may
-become much shorter.
-
-@itemize @bullet
-@item @b{arm7_9 fast_writes}
-@cindex arm7_9 fast_writes
-@*Use @command{arm7_9 fast_memory_access} instead.
-@xref{arm7_9 fast_memory_access}.
-@item @b{endstate}
-@cindex endstate
-@*An buggy old command that would not really work since background polling would wipe out the global endstate
-@item @b{arm7_9 force_hw_bkpts}
-@*Use @command{gdb_breakpoint_override} instead. Note that GDB will use hardware breakpoints
-for flash if the GDB memory map has been set up(default when flash is declared in
-target configuration). @xref{gdb_breakpoint_override}.
-@item @b{arm7_9 sw_bkpts}
-@*On by default. @xref{gdb_breakpoint_override}.
-@item @b{daemon_startup}
-@*this config option has been removed, simply adding @option{init} and @option{reset halt} to
-the end of your config script will give the same behaviour as using @option{daemon_startup reset}
-and @option{target cortex_m3 little reset_halt 0}.
-@item @b{dump_binary}
-@*use @option{dump_image} command with same args. @xref{dump_image}.
-@item @b{flash erase}
-@*use @option{flash erase_sector} command with same args. @xref{flash erase_sector}.
-@item @b{flash write}
-@*use @option{flash write_bank} command with same args. @xref{flash write_bank}.
-@item @b{flash write_binary}
-@*use @option{flash write_bank} command with same args. @xref{flash write_bank}.
-@item @b{flash auto_erase}
-@*use @option{flash write_image} command passing @option{erase} as the first parameter. @xref{flash write_image}.
-
-@item @b{jtag_device}
-@*use the @command{jtag newtap} command, converting from positional syntax
-to named prefixes, and naming the TAP.
-@xref{jtag newtap}.
-Note that if you try to use the old command, a message will tell you the
-right new command to use; and that the fourth parameter in the old syntax
-was never actually used.
-@example
-OLD: jtag_device 8 0x01 0xe3 0xfe
-NEW: jtag newtap CHIPNAME TAPNAME \
-           -irlen 8 -ircapture 0x01 -irmask 0xe3
-@end example
-
-@item @b{jtag_speed} value
-@*@xref{JTAG Speed}.
-Usually, a value of zero means maximum
-speed. The actual effect of this option depends on the JTAG interface used.
-@itemize @minus
-@item wiggler: maximum speed / @var{number}
-@item ft2232: 6MHz / (@var{number}+1)
-@item amt jtagaccel: 8 / 2**@var{number}
-@item jlink: maximum speed in kHz (0-12000), 0 will use RTCK
-@item rlink: 24MHz / @var{number}, but only for certain values of @var{number}
-@comment end speed list.
-@end itemize
-
-@item @b{load_binary}
-@*use @option{load_image} command with same args. @xref{load_image}.
-@item @b{run_and_halt_time}
-@*This command has been removed for simpler reset behaviour, it can be simulated with the
-following commands:
-@smallexample
-reset run
-sleep 100
-halt
-@end smallexample
-@item @b{target} <@var{type}> <@var{endian}> <@var{jtag-position}>
-@*use the create subcommand of @option{target}.
-@item @b{target_script} <@var{target#}> <@var{eventname}> <@var{scriptname}>
-@*use <@var{target_name}> configure -event <@var{eventname}> "script <@var{scriptname}>"
-@item @b{working_area}
-@*use the @option{configure} subcommand of @option{target} to set the work-area-virt, work-area-phy, work-area-size, and work-area-backup properties of the target.
-@end itemize
-
 @node FAQ
 @chapter FAQ
 @cindex faq