1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
|
\chapter{``M'' Standard Extension for Integer Multiplication and
Division, Version 2.0}
This chapter describes the standard integer multiplication and
division instruction extension, which is named ``M'' and contains
instructions that multiply or divide values held in two integer
registers.
\begin{commentary}
We separate integer multiply and divide out from the base to simplify
low-end implementations, or for applications where integer multiply
and divide operations are either infrequent or better handled in
attached accelerators.
\end{commentary}
\section{Multiplication Operations}
\vspace{-0.2in}
\begin{center}
\begin{tabular}{S@{}R@{}R@{}S@{}R@{}O}
\\
\instbitrange{31}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct7} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{funct3} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
7 & 5 & 5 & 3 & 5 & 7 \\
MULDIV & multiplier & multiplicand & MUL/MULH[[S]U] & dest & OP \\
MULDIV & multiplier & multiplicand & MULW & dest & OP-32 \\
\end{tabular}
\end{center}
MUL performs an XLEN-bit$\times$XLEN-bit multiplication and places the
lower XLEN bits in the destination register. MULH, MULHU, and MULHSU
perform the same multiplication but return the upper XLEN bits of the
full 2$\times$XLEN-bit product, for signed$\times$signed,
unsigned$\times$unsigned, and signed$\times$unsigned multiplication
respectively. If both the high and low bits of the same product are
required, then the recommended code sequence is: MULH[[S]U] {\em rdh,
rs1, rs2}; MUL {\em rdl, rs1, rs2} (source register specifiers must
be in same order and {\em rdh} cannot be the same as {\em rs1} or {\em
rs2}). Microarchitectures can then fuse these into a single
multiply operation instead of performing two separate multiplies.
MULW is only valid for RV64, and multiplies the lower
32 bits of the source registers, placing the sign-extension of the
lower 32 bits of the result into the destination register. MUL can be
used to obtain the upper 32 bits of the 64-bit product, but signed
arguments must be proper 32-bit signed values, whereas unsigned
arguments must have their upper 32 bits clear.
\section{Division Operations}
\vspace{-0.2in}
\begin{center}
\begin{tabular}{S@{}R@{}R@{}O@{}R@{}O}
\\
\instbitrange{31}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct7} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{funct3} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
7 & 5 & 5 & 3 & 5 & 7 \\
MULDIV & divisor & dividend & DIV[U]/REM[U] & dest & OP \\
MULDIV & divisor & dividend & DIV[U]W/REM[U]W & dest & OP-32 \\
\end{tabular}
\end{center}
DIV and DIVU perform signed and unsigned integer division of XLEN
bits by XLEN bits. REM and REMU provide the remainder of the
corresponding division operation. If both the quotient and remainder
are required from the same division, the recommended code sequence is:
DIV[U] {\em rdq, rs1, rs2}; REM[U] {\em rdr, rs1, rs2} ({\em rdq}
cannot be the same as {\em rs1} or {\em rs2}). Microarchitectures can
then fuse these into a single divide operation instead of performing
two separate divides.
DIVW and DIVUW instructions are only valid for RV64, and divide the
lower 32 bits of {\em rs1} by the lower 32 bits of {\em rs2}, treating
them as signed and unsigned integers respectively, placing the 32-bit
quotient in {\em rd}, sign-extended to 64 bits. REMW and REMUW
instructions are only valid for RV64, and provide the corresponding
signed and unsigned remainder operations respectively. Both REMW and
REMUW sign-extend the 32-bit result to 64 bits.
The semantics for division by zero and division overflow are summarized in
Table~\ref{tab:divby0}. The quotient of division by zero has all bits set,
i.e. $2^{XLEN}-1$ for unsigned division or $-1$ for signed division. The
remainder of division by zero equals the dividend. Signed division overflow
occurs only when the most-negative integer, $-2^{XLEN-1}$, is divided by $-1$.
The quotient of signed division overflow is equal to the dividend, and the
remainder is zero. Unsigned division overflow cannot occur.
\vspace{0.1in}
\begin{table}[h]
\center
\begin{tabular}{|l|c|c||c|c|c|c|}
\hline
Condition & Dividend & Divisor & DIVU & REMU & DIV & REM \\ \hline
Division by zero & $x$ & 0 & $2^{XLEN}-1$ & $x$ & $-1$ & $x$ \\
Overflow (signed only) & $-2^{XLEN-1}$ & $-1$ & -- & -- & $-2^{XLEN-1}$ & 0 \\
\hline
\end{tabular}
\caption{Semantics for division by zero and division overflow.}
\label{tab:divby0}
\end{table}
\begin{commentary}
We considered raising exceptions on integer divide by zero, with these
exceptions causing a trap in most execution environments. However,
this would be the only arithmetic trap in the standard ISA
(floating-point exceptions set flags and write default values, but do
not cause traps) and would require language implementors to interact
with the execution environment's trap handlers for this case.
Further, where language standards mandate that a divide-by-zero
exception must cause an immediate control flow change, only a single
branch instruction needs to be added to each divide operation, and
this branch instruction can be inserted after the divide and should
normally be very predictably not taken, adding little runtime
overhead.
\end{commentary}
|
