\chapter{``F'' Standard Extension for Single-Precision Floating-Point,
Version 2.0}
\label{sec:single-float}

This chapter describes the standard instruction-set extension for
single-precision floating-point, which is named ``F'' and adds
single-precision floating-point computational instructions compliant
with the IEEE 754-2008 arithmetic standard~\cite{ieee754-2008}.


\section{F Register State}

The F extension adds 32 floating-point registers, {\tt f0}--{\tt f31},
each 32 bits wide, and a floating-point control and status register
{\tt fcsr}, which contains the operating mode and exception status of the
floating-point unit.  This additional state is shown in
Figure~\ref{fprs}.  We use the term FLEN to describe the width of the
floating-point registers in the RISC-V ISA, and FLEN=32 for the F
single-precision floating-point extension.  Most floating-point
instructions operate on values in the floating-point register file.
Floating-point load and store instructions transfer floating-point
values between registers and memory.  Instructions to transfer values
to and from the integer register file are also provided.

\begin{figure}[htbp]
{\footnotesize
\begin{center}
\begin{tabular}{p{2in}}
\instbitrange{FLEN-1}{0}                                    \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f0\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f1\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f2\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f3\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f4\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f5\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f6\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f7\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f8\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ \ f9\ \ \ \ \ }}       \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f10\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f11\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f12\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f13\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f14\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f15\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f16\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f17\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f18\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f19\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f20\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f21\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f22\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f23\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f24\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f25\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f26\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f27\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f28\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f29\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f30\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{\ \ \ f31\ \ \ \ \ }}        \\ \cline{1-1}
\multicolumn{1}{c}{FLEN}                                    \\

\instbitrange{31}{0}                                        \\ \cline{1-1}
\multicolumn{1}{|c|}{\reglabel{fcsr}}                       \\ \cline{1-1}
\multicolumn{1}{c}{32}                                      \\
\end{tabular}
\end{center}
}
\caption{RISC-V standard F extension single-precision floating-point state.}
\label{fprs}
\end{figure}

\begin{commentary}
We considered a unified register file for both integer and
floating-point values as this simplifies software register allocation
and calling conventions, and reduces total user state.  However, a
split organization increases the total number of registers accessible
with a given instruction width, simplifies provision of enough regfile
ports for wide superscalar issue, supports decoupled
floating-point-unit architectures, and simplifies use of internal
floating-point encoding techniques.  Compiler support and calling
conventions for split register file architectures are well understood,
and using dirty bits on floating-point register file state can reduce
context-switch overhead.
\end{commentary}

\clearpage

\section{Floating-Point Control and Status Register}

The floating-point control and status register, {\tt fcsr}, is a RISC-V
control and status register (CSR).  It is a 32-bit read/write register that
selects the dynamic rounding mode for floating-point arithmetic operations and
holds the accrued exception flags, as shown in Figure~\ref{fcsr}.

\begin{figure*}
{\footnotesize
\begin{center}
\begin{tabular}{K@{}E@{}ccccc}
\instbitrange{31}{8} &
\instbitrange{7}{5} &
\instbit{4} &
\instbit{3} &
\instbit{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{0} &
\multicolumn{1}{c|}{Rounding Mode ({\tt frm})} &
\multicolumn{5}{c|}{Accrued Exceptions ({\tt fflags})} \\
\hline
\multicolumn{1}{c}{} &
\multicolumn{1}{c|}{} &
\multicolumn{1}{c|}{NV} &
\multicolumn{1}{c|}{DZ} &
\multicolumn{1}{c|}{OF} &
\multicolumn{1}{c|}{UF} &
\multicolumn{1}{c|}{NX} \\
\cline{3-7}
24 & 3 & 1 & 1 & 1 & 1 & 1 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Floating-point control and status register.}
\label{fcsr}
\end{figure*}

The {\tt fcsr} register can be read and written with the FRCSR and
FSCSR instructions, which are assembler pseudo-ops built on the
underlying CSR access instructions.  FRCSR reads {\tt fcsr} by copying
it into integer register {\em rd}.  FSCSR swaps the value in {\tt
  fcsr} by copying the original value into integer register {\em rd},
and then writing a new value obtained from integer register {\em rs1}
into {\tt fcsr}.

The fields within the {\tt fcsr} can also be accessed individually
through different CSR addresses, and separate assembler pseudo-ops are
defined for these accesses.  The FRRM instruction reads the Rounding
Mode field {\tt frm} and copies it into the least-significant three
bits of integer register {\em rd}, with zero in all other bits.  FSRM
swaps the value in {\tt frm} by copying the original value into
integer register {\em rd}, and then writing a new value obtained from
the three least-significant bits of integer register {\em rs1} into
{\tt frm}.  FRFLAGS and FSFLAGS are defined analogously for the
Accrued Exception Flags field {\tt fflags}.  Additional
pseudo-instructions FSRMI and FSFLAGSI swap values using an immediate
value instead of register {\em rs1}.

Floating-point operations use either a static rounding mode encoded in the
instruction, or a dynamic rounding mode held in {\tt frm}.  Rounding modes are
encoded as shown in Table~\ref{rm}.  A value of 111 in the instruction's {\em
rm} field selects the dynamic rounding mode held in {\tt frm}.  If {\tt frm}
is set to an invalid value (101--111), any subsequent attempt to execute
a floating-point operation with a dynamic rounding mode will cause an illegal
instruction trap.  Some instructions that have the {\em rm} field are
nevertheless unaffected by the rounding mode; they should have their {\em rm}
field set to RNE (000).

\begin{commentary}
The C99 language standard effectively mandates the provision of a
dynamic rounding mode register.
\end{commentary}
\newpage
 
\begin{table}[htp]
\begin{small}
\begin{center}
\begin{tabular}{ccl}
\hline
\multicolumn{1}{|c|}{Rounding Mode} &
\multicolumn{1}{c|}{Mnemonic} &
\multicolumn{1}{c|}{Meaning} \\
\hline
\multicolumn{1}{|c|}{000} &
\multicolumn{1}{l|}{RNE} &
\multicolumn{1}{l|}{Round to Nearest, ties to Even}\\
\hline
\multicolumn{1}{|c|}{001} &
\multicolumn{1}{l|}{RTZ} &
\multicolumn{1}{l|}{Round towards Zero}\\
\hline
\multicolumn{1}{|c|}{010} &
\multicolumn{1}{l|}{RDN} &
\multicolumn{1}{l|}{Round Down (towards $-\infty$)}\\
\hline
\multicolumn{1}{|c|}{011} &
\multicolumn{1}{l|}{RUP} &
\multicolumn{1}{l|}{Round Up (towards $+\infty$)}\\
\hline
\multicolumn{1}{|c|}{100} &
\multicolumn{1}{l|}{RMM} &
\multicolumn{1}{l|}{Round to Nearest, ties to Max Magnitude}\\
\hline
\multicolumn{1}{|c|}{101} &
\multicolumn{1}{l|}{} &
\multicolumn{1}{l|}{\em Invalid.  Reserved for future use.}\\
\hline
\multicolumn{1}{|c|}{110} &
\multicolumn{1}{l|}{} &
\multicolumn{1}{l|}{\em Invalid.  Reserved for future use.}\\
\hline
\multicolumn{1}{|c|}{111} &
\multicolumn{1}{l|}{} &
\multicolumn{1}{l|}{In instruction's {\em rm} field, selects dynamic rounding mode;}\\
\multicolumn{1}{|c|}{} &
\multicolumn{1}{l|}{} &
\multicolumn{1}{l|}{In Rounding Mode register, {\em Invalid}.}\\
\hline
\end{tabular}
\end{center}
\end{small}
\caption{Rounding mode encoding.}
\label{rm}
\end{table}

The accrued exception flags indicate the exception conditions that
have arisen on any floating-point arithmetic instruction since the
field was last reset by software, as shown in Table~\ref{bitdef}.

\begin{table}[htp]
\begin{small}
\begin{center}
\begin{tabular}{cl}
\hline
\multicolumn{1}{|c|}{Flag Mnemonic} &
\multicolumn{1}{c|}{Flag Meaning} \\
\hline
\multicolumn{1}{|c|}{NV} &
\multicolumn{1}{c|}{Invalid Operation}\\
\hline
\multicolumn{1}{|c|}{DZ} &
\multicolumn{1}{c|}{Divide by Zero}\\
\hline
\multicolumn{1}{|c|}{OF} &
\multicolumn{1}{c|}{Overflow}\\
\hline
\multicolumn{1}{|c|}{UF} &
\multicolumn{1}{c|}{Underflow}\\
\hline
\multicolumn{1}{|c|}{NX} &
\multicolumn{1}{c|}{Inexact}\\
\hline
\end{tabular}
\end{center}
\end{small}
\caption{Accrued exception flag encoding.}
\label{bitdef}
\end{table}

\begin{commentary}
As allowed by the standard, we do not support traps on floating-point
exceptions in the base ISA, but instead require explicit checks of the flags
in software.  We considered adding branches controlled directly by the
contents of the floating-point accrued exception flags, but ultimately chose
to omit these instructions to keep the ISA simple.
\end{commentary}

\section{NaN Generation and Propagation}

Except when otherwise stated, if the result of a floating-point operation is
NaN, it is the canonical NaN.  The canonical NaN has a positive sign and all
significand bits clear except the MSB, a.k.a. the quiet bit.  For
single-precision floating-point, this corresponds to the pattern {\tt
0x7fc00000}.

For FMIN and FMAX, if at least one input is a signaling NaN, or if both inputs
are quiet NaNs, the result is the canonical NaN.  If one operand is a quiet NaN
and the other is not a NaN, the result is the non-NaN operand.

The sign-injection instructions (FSGNJ, FSGNJN, FSGNJX) do not canonicalize
NaNs; they manipulate the underlying bit patterns directly.

\begin{commentary}
We considered propagating NaN payloads, as is recommended by the standard,
but this decision would have increased hardware cost.  Moreover, since this
feature is optional in the standard, it cannot be used in portable code.

Implementors are free to provide a NaN payload propagation scheme as
a nonstandard extension enabled by a nonstandard operating mode.  However, the
canonical NaN scheme described above must always be supported and should be
the default mode.
\end{commentary}

\begin{commentary}
We require implementations to return the standard-mandated default
values in the case of exceptional conditions, without any further
intervention on the part of user-level software (unlike the Alpha ISA
floating-point trap barriers).  We believe full hardware handling of
exceptional cases will become more common, and so wish to avoid
complicating the user-level ISA to optimize other approaches.
Implementations can always trap to machine-mode software handlers to
provide exceptional default values.
\end{commentary}

\section{Subnormal Arithmetic}

Operations on subnormal numbers are handled in accordance with the IEEE
754-2008 standard.

In the parlance of the IEEE standard, tininess is detected after
rounding---that is, the underflow exception is raised only if the rounded
result is subnormal, even if the unrounded result would have been subnormal.

\begin{commentary}
Detecting tininess after rounding results in fewer spurious underflow signals.
\end{commentary}

\section{Single-Precision Load and Store Instructions}

Floating-point loads and stores use the same base+offset addressing
mode as the integer base ISA, with a base address in register {\em
  rs1} and a 12-bit signed byte offset.  The FLW instruction loads a
single-precision floating-point value from memory into floating-point
register {\em rd}.  FSW stores a single-precision value from
floating-point register {\em rs2} to memory.

\vspace{-0.2in}
\begin{center}
\begin{tabular}{M@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{imm[11:0]} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{width} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
12 & 5 & 3 & 5 & 7 \\
offset[11:0] & base & W & dest & LOAD-FP \\
\end{tabular}
\end{center}

\vspace{-0.2in}
\begin{center}
\begin{tabular}{O@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{imm[11:5]} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{width} &
\multicolumn{1}{c|}{imm[4:0]} &
\multicolumn{1}{c|}{opcode} \\
\hline
7 & 5 & 5 & 3 & 5 & 7 \\
offset[11:5] & src & base & W & offset[4:0] & STORE-FP \\
\end{tabular}
\end{center}

FLW and FSW are only guaranteed to execute atomically if the effective address
is naturally aligned.

\section{Single-Precision Floating-Point Computational Instructions}
\label{sec:single-float-compute}

Floating-point arithmetic instructions with one or two source operands use the
R-type format with the OP-FP major opcode.  FADD.S, FSUB.S,
FMUL.S, and FDIV.S perform single-precision floating-point addition,
subtraction, multiplication, and division, respectively, between {\em rs1} and
{\em rs2}, writing the result to {\em rd}.  FMIN.S and FMAX.S
write, respectively, the smaller or larger of {\em rs1} and {\em rs2} to {\em
rd}.  FSQRT.S computes the square root of {\em rs1} and writes the
result to {\em rd}.

The 2-bit floating-point format field {\em fmt} is encoded as shown in
Table~\ref{tab:fmt}.  It is set to {\em S} (00) for all instructions in
the F extension.

\begin{table}[htp]
\begin{small}
\begin{center}
\begin{tabular}{|c|c|l|}
\hline
{\em fmt} field &
Mnemonic &
Meaning \\
\hline
00 & S & 32-bit single-precision \\
01 & D & 64-bit double-precision \\
10 & - & {\em reserved} \\
11 & Q & 128-bit quad-precision \\
\hline
\end{tabular}
\end{center}
\end{small}
\caption{Format field encoding.}
\label{tab:fmt}
\end{table}

All floating-point operations that perform rounding can select the
rounding mode using the {\em rm} field with the encoding shown in
Table~\ref{rm}.

\vspace{-0.2in}
\begin{center}
\begin{tabular}{R@{}F@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{27} &
\instbitrange{26}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct5} &
\multicolumn{1}{c|}{fmt} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{rm} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
5 & 2 & 5 & 5 & 3 & 5 & 7 \\
FADD/FSUB & S & src2 & src1 & RM  & dest & OP-FP  \\
FMUL/FDIV & S & src2 & src1 & RM  & dest & OP-FP  \\
FMIN-MAX  & S & src2 & src1 & MIN/MAX & dest & OP-FP  \\
FSQRT     & S & 0    & src  & RM  & dest & OP-FP  \\
\end{tabular}
\end{center}

Floating-point fused multiply-add instructions require a new standard
instruction format.  R4-type instructions specify three source
registers ({\em rs1}, {\em rs2}, and {\em rs3}) and a destination
register ({\em rd}).  This format is only used by the floating-point
fused multiply-add instructions.  Fused multiply-add instructions
multiply the values in {\em rs1} and {\em rs2}, optionally negate the
product, then add or subtract the value in {\em rs3}, writing the final
result to {\em rd}.
FMADD.S computes {\em rs1$\times$rs2+rs3}; FMSUB.S computes
{\em rs1$\times$rs2-rs3}; FNMSUB.S computes {\em
  -rs1$\times$rs2+rs3}; and FNMADD.S computes {\em
  -rs1$\times$rs2-rs3}.

\vspace{-0.2in}
\begin{center}
\begin{tabular}{R@{}F@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{27} &
\instbitrange{26}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{rs3} &
\multicolumn{1}{c|}{fmt} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{rm} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
5 & 2 & 5 & 5 & 3 & 5 & 7 \\
src3 & S & src2 & src1 & RM  & dest & F[N]MADD/F[N]MSUB  \\
\end{tabular}
\end{center}

\section{Single-Precision Floating-Point Conversion and Move \mbox{Instructions}}

Floating-point-to-integer and integer-to-floating-point conversion
instructions are encoded in the OP-FP major opcode space.
FCVT.W.S or FCVT.L.S converts a floating-point number
in floating-point register {\em rs1} to a signed 32-bit or 64-bit
integer, respectively, in integer register {\em rd}.  FCVT.S.W
or FCVT.S.L converts a 32-bit or 64-bit signed integer,
respectively, in integer register {\em rs1} into a floating-point
number in floating-point register {\em rd}. FCVT.WU.S,
FCVT.LU.S, FCVT.S.WU, and FCVT.S.LU variants
convert to or from unsigned integer values.  FCVT.L[U].S and
FCVT.S.L[U] are illegal in RV32.
If the rounded result is not representable in the destination format,
it is clipped to the nearest value and the invalid flag is set.
Table~\ref{tab:int_conv} gives the range of valid inputs for FCVT.{\em int}.S
and the behavior for invalid inputs.

\begin{table}[htp]
\begin{small}
\begin{center}
\begin{tabular}{|l|r|r|r|r|}
\hline
 & FCVT.W.S & FCVT.WU.S & FCVT.L.S & FCVT.LU.S \\
\hline
Minimum valid input (after rounding) & $-2^{31}$ & 0 & $-2^{63}$ & 0 \\
Maximum valid input (after rounding) & $2^{31}-1$ & $2^{32}-1$ & $2^{63}-1$ & $2^{64}-1$ \\
\hline
Output for out-of-range negative input & $-2^{31}$ & 0 & $-2^{63}$ & 0 \\
Output for $-\infty$ & $-2^{31}$ & 0 & $-2^{63}$ & 0 \\
Output for out-of-range positive input & $2^{31}-1$ & $2^{32}-1$ & $2^{63}-1$ & $2^{64}-1$ \\
Output for $+\infty$ or NaN & $2^{31}-1$ & $2^{32}-1$ & $2^{63}-1$ & $2^{64}-1$ \\
\hline
\end{tabular}
\end{center}
\end{small}
\caption{Domains of float-to-integer conversions and behavior for invalid inputs.}
\label{tab:int_conv}
\end{table}

All floating-point to integer and integer to floating-point conversion
instructions round according to the {\em rm} field.  A floating-point register
can be initialized to floating-point positive zero using FCVT.S.W {\em rd},
{\tt x0}, which will never raise any exceptions.

\vspace{-0.2in}
\begin{center}
\begin{tabular}{R@{}F@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{27} &
\instbitrange{26}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct5} &
\multicolumn{1}{c|}{fmt} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{rm} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
5 & 2 & 5 & 5 & 3 & 5 & 7 \\
FCVT.{\em int}.{\em fmt} & S & W[U]/L[U] & src & RM  & dest & OP-FP  \\
FCVT.{\em fmt}.{\em int} & S & W[U]/L[U] & src & RM  & dest & OP-FP  \\
\end{tabular}
\end{center}

Floating-point to floating-point sign-injection instructions, FSGNJ.S,
FSGNJN.S, and FSGNJX.S, produce a result that takes all bits except
the sign bit from {\em rs1}.  For FSGNJ, the result's sign bit is {\em
  rs2}'s sign bit; for FSGNJN, the result's sign bit is the opposite
of {\em rs2}'s sign bit; and for FSGNJX, the sign bit is the XOR of
the sign bits of {\em rs1} and {\em rs2}.  Sign-injection instructions
do not set floating-point exception flags.  Note, FSGNJ.S {\em rx, ry,
  ry} moves {\em ry} to {\em rx} (assembler pseudo-op FMV.S {\em rx,
  ry}); FSGNJN.S {\em rx, ry, ry} moves the the negation of {\em ry} to
{\em rx} (assembler pseudo-op FNEG.S {\em rx, ry}); and FSGNJX.S {\em rx,
  ry, ry} moves the absolute value of {\em ry} to {\em rx} (assembler
pseudo-op FABS.S {\em rx, ry}).

\vspace{-0.2in}
\begin{center}
\begin{tabular}{R@{}F@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{27} &
\instbitrange{26}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct5} &
\multicolumn{1}{c|}{fmt} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{rm} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
5 & 2 & 5 & 5 & 3 & 5 & 7 \\
FSGNJ & S & src2 & src1 & J[N]/JX & dest & OP-FP  \\
\end{tabular}
\end{center}

\begin{commentary}
The sign-injection instructions
provide floating-point MV, ABS, and NEG,
as well as supporting a few other operations, including the IEEE copySign
operation and sign manipulation in transcendental math function
libraries.  Although MV, ABS, and NEG only need a single register
operand, whereas FSGNJ instructions need two, it is unlikely most
microarchitectures would add optimizations to benefit from the reduced
number of register reads for these relatively infrequent instructions.
Even in this case, a microarchitecture can simply detect when both
source registers are the same for FSGNJ instructions and only read a
single copy.
\end{commentary}

Instructions are provided to move bit patterns between the
floating-point and integer registers.  FMV.X.S moves the
single-precision value in floating-point register {\em rs1}
represented in IEEE 754-2008 encoding to the lower 32 bits of integer
register {\em rd}.  For RV64, the higher 32 bits of the destination
register are filled with copies of the floating-point number's sign
bit.  FMV.S.X moves the single-precision value encoded in IEEE
754-2008 standard encoding from the lower 32 bits of integer register
{\em rs1} to the floating-point register {\em rd}.  The bits are not
modified in the transfer, and in particular, the payloads of
non-canonical NaNs are preserved.

\vspace{-0.2in}
\begin{center}
\begin{tabular}{R@{}F@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{27} &
\instbitrange{26}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct5} &
\multicolumn{1}{c|}{fmt} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{rm} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
5 & 2 & 5 & 5 & 3 & 5 & 7 \\
FMV.X.{\em fmt} & S & 0    & src  & 000  & dest & OP-FP  \\
FMV.{\em fmt}.X & S & 0    & src  & 000  & dest & OP-FP  \\
\end{tabular}
\end{center}

\begin{commentary}
The base floating-point ISA was defined so as to allow implementations
to employ an internal recoding of the floating-point format in
registers to simplify handling of subnormal values and possibly to
reduce functional unit latency.  To this end, the base ISA avoids
representing integer values in the floating-point registers by
defining conversion and comparison operations that read and write the
integer register file directly.  This also removes many of the common
cases where explicit moves between integer and floating-point
registers are required, reducing instruction count and critical paths
for common mixed-format code sequences.
\end{commentary}

\section{Single-Precision Floating-Point Compare Instructions}

Floating-point compare instructions perform the specified comparison (equal,
less than, or less than or equal) between floating-point registers {\em rs1}
and {\em rs2} and record the Boolean result in integer register {\em rd}.

FLT.S and FLE.S perform what the IEEE 754-2008 standard refers to as {\em
signaling} comparisons: that is, an Invalid Operation exception is raised if
either input is NaN.  FEQ.S performs a {\em quiet} comparison: only signaling
NaN inputs cause an Invalid Operation exception.  For all three instructions,
the result is 0 if either operand is NaN.

\vspace{-0.2in}
\begin{center}
\begin{tabular}{S@{}F@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{27} &
\instbitrange{26}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct5} &
\multicolumn{1}{c|}{fmt} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{rm} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
5 & 2 & 5 & 5 & 3 & 5 & 7 \\
FCMP & S & src2 & src1 & EQ/LT/LE & dest & OP-FP  \\
\end{tabular}
\end{center}

\section{Single-Precision Floating-Point Classify Instruction}

The FCLASS.S instruction examines the value in floating-point register {\em
rs1} and writes to integer register {\em rd} a 10-bit mask that indicates
the class of the floating-point number.  The format of the mask is
described in Table~\ref{tab:fclass}.  The corresponding bit in {\em rd} will
be set if the the property is true and clear otherwise.  All other bits in
{\em rd} are cleared.  Note that exactly one bit in {\em rd} will be set.

\vspace{-0.2in}
\begin{center}
\begin{tabular}{S@{}F@{}R@{}R@{}F@{}R@{}O}
\\
\instbitrange{31}{27} &
\instbitrange{26}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct5} &
\multicolumn{1}{c|}{fmt} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{rm} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
5 & 2 & 5 & 5 & 3 & 5 & 7 \\
FCLASS & S & 0 & src & 001 & dest & OP-FP  \\
\end{tabular}
\end{center}

\begin{table}[htp]
\begin{small}
\begin{center}
\begin{tabular}{|c|l|}
\hline
{\em rd} bit &
Meaning \\
\hline
0 & {\em rs1} is $-\infty$. \\
1 & {\em rs1} is a negative normal number. \\
2 & {\em rs1} is a negative subnormal number. \\
3 & {\em rs1} is $-0$. \\
4 & {\em rs1} is $+0$. \\
5 & {\em rs1} is a positive subnormal number. \\
6 & {\em rs1} is a positive normal number. \\
7 & {\em rs1} is $+\infty$. \\
8 & {\em rs1} is a signaling NaN. \\
9 & {\em rs1} is a quiet NaN. \\
\hline
\end{tabular}
\end{center}
\end{small}
\caption{Format of result of FCLASS instruction.}
\label{tab:fclass}
\end{table}